LaLaLand CS Midi Series User manual
CS20M Midi Kit
Installation manual
CS20M MIDI Kit Installation Manual
CS Series Midi Kit:
Tools needed
Philips screwdriver
3.5mm drill for screws
(Optional 3mm tap drill)
15mm step drill
Content
• CS MIDI board
• 1x3 pin power cable (RED, BLUE, BLACK)
• 1x6 pin keyboard cable (MULTICOLORED)
• 1x7 pin keyboard cable (MULTICOLORED)
• 1x2 pin filter control cable (ORANGE, PURPLE)
• 2x prewired MIDI sockets plus 4x screws & 4x nuts
• 4x plastic standoffs
• 1x MIDI connector sticker (Used as drilling template)
Introduction
The CS Filter Modulator
Check out our plugin for the CS series - click here
CS20M MIDI Kit Installation Manual
Installation
The CS Midi board is installed between the keyboard and the
key assigner board and therefore requires only 2 cables to solder (Filters).
Removal of the key assigner is not required. Although we suggest
calibrating the synth before install, recalibration after install is not
required.
Midi connectors will require drilling using the drill template/sticker.
To open the CS20M remove the 7 screws on the bottom.
Make sure to disconnect synth from mains before proceeding with installation!
Follow the step by step instructions in the following pages to install your
CS MIDIKIT.
CS20M MIDI Kit Installation Manual
MIDI connectors installation
Start by drilling and mounting the midi connectors using the midi sticker as a tem-
plate, place the sticker in the desired location and fasten at the top with tape and
mark the center X’s. Next lift up the sticker while the tape holds it in place and drill
the holes for the midi connectors.
Place the midi connectors in the slots and mark where to drill for the screws., after
drilling remove the backing from the sticker and fasten it in place. Cut out the holes
in the sticker, an 8 cut “pizza” cut works great. Place midi connectors and fasten
with screws. See images below.(Alternatively you can print out and use the MIDI
template on the last page).
NOTE: MIDI In connector has two wires and MIDI Out has three.
The board is placed on the right side to the SSK/Key Assigner board under the key-
board. Lift up the keyboard, and place the midi kit as shown in image below. Screw
the board in place using the plastic standoffs.
CS20M MIDI Kit Installation Manual
Connect the power cables
Locate the 5 pin connnector (+15, -15, GND/EK) on the board as shown in the image
(SSK board, bottom of the synth, under keyboard).
Using the 3 Wire (Red, Black, Blue) power cable,insert the connector while taking
care of the correct orientation.
NEG/BLUE is the -15V.
POS/RED is the +15V.
GND/EK/BLACK is the ground cable
CS20M MIDI Kit Installation Manual
Now plug the Power cable into Power on the MIDI Board as shown in image.
Locate and disconnect the 6 and 7 pin cables on the key assigner PCB.
CS20M MIDI Kit Installation Manual
Connect the 7 pin cable to the midi board as shown in image.
Connect the 6 pin cable to the midi board as shown in image.
CS20M MIDI Kit Installation Manual
Now connect the provided 6 pin cable to the MIDI board as shown in image
Connect the provided 7 pin cable to the MIDI board as shown in image
CS20M MIDI Kit Installation Manual
Connect the 6 and 7 pin cables to the MIDI board as shown in image.
(where you previously diconnected the original cables).
Connect the MIDI in and out cables as shown in image.
NOTE: At this point the board, MIDI in/out is operational.
Filter control is optional.
CS20M MIDI Kit Installation Manual
Solder the filter cable(s)
Locate the solder point shown in this image (The right front panel board).
Use the provided orange and Purple cable.
Solder the orange wire to this point shown in image (Purple is not used).
CS20M MIDI Kit Installation Manual
You have completed the full installation.
MIDI in/out, filter and all features are now operational.
Secure all wiring with the included zip ties.
Close the synth and connect to mains.
Disclaimer: Lalalandsynth is not responsible for any damage caused by improper installation.
Now connect the 2 pin connector to the FILTER connector on the
midi board as shown in image.
CS20M MIDI Kit Installation Manual
MIDI drill template
Print out and use as drill template.
Other manuals for CS Midi Series
2
This manual suits for next models
1
Table of contents
Other LaLaLand Recording Equipment manuals
