Lamona LAM8702 User manual

Installation Instructions
Washing Machine
(To be used in conjunction with User Instructions)
lPlease read these Installation Instructions to ensure safe,
 correctttingofthisappliance.
lThewashingmachineshouldbettedbyasuitablycompetent,
 qualiedperson.
lPleasekeeptheseinstructionsinasafeplaceforfuturereference.
lDangerofsuffocationkeeppackagingmaterialawayfromchildren.
LAM8702/03
Warning for hazardous
situations with regard to
lifeandproperty.
Warning for
electricshock.
Warning for
riskofre.
Throughout this manual the
followingsymbolsareused.

2
10mmopen
endedspanner Flat and
cross head
screw drivers
DO NOT use high
speedimpact
powertools.
www.howdens.com
Safety Information
Installation
Tools required
Twopersonlift. Riskofinjury:
Bewareofsharpmetal
edges.Usegloveswhen
handling.
NOTE:Iftheelectricity
cable is damaged it
mustbereplacedbya
competentperson.
Washing machine must
bexedsecurelyand
level.
Risk of damage to
property:
Take care of surrounding
area when moving the
appliancetoprevent
damagetoooring,wall
coverings,pipesetc..
Ensurethatallpacking
andtransitprotectors
have been removed
fromtheappliance
beforepositioning.
DO NOT PUSH
against the washing
machinefasciapanel.
Thisapplianceisnot
designed for stacking
withotherappliances.

3
B(3x15mm)
A(4.5x10)
x2
x1
x2 x2 x5
x1
www.howdens.com
1. Remove transit POLY BLOCK..........................p.4
2. Removetransitbolts...........................................p.4
3. Dimensions..........................................................p.5
4. Fitfascialletandanti-tiltsupport....................p.5
5. Preparethedécordoor.......................................p.6
6. Washing machine connections..........................p.7
7. Connecting water hose.......................................p.8
8. Positioning the washing machine......................p.9
9. Fitdécordoorandmagneticcatches...............p.10
10. Raise and level the machine..............................p.11
11.Drainhoseandlter............................................p.12
12. Plinth.....................................................................p.12
Parts supplied
Fitting guide
Copyright©2018HowdenJoineryLtd.Allrightsreserved.

4
IMPORTANT:
REMOVE POLY BLOCK.
10mmopen
endedspanner
www.howdens.com
1- Remove transit item
2- Remove transit bolts

5
Position the washing machine
relativetoserviceconnections.
Décor fillet
can be added
Example
nominal
set-up
Min 5mm
Max 15mm
Anti-tilt block
45-50mm
*25mm
Approx 830mm
*At nominal set up -
165mm from floor to the
base of cabinet.
min
15mm
817mm-
831mm
554mm 597mm
820-920mm
min
575mm
*600mm
www.howdens.com
3- Dimensions
4 - Fit décor llet and anti-tilt block
*Ensuretheoorislevelandstrongenough
tosupportafullyloadedwashingmachine.

6
edge of door
35mm
47mm
2mm
22.5mm
4.5mm
edge of door
45mm
2mm
31mm
468.5mm
597mm
716mm
384mm
84.5mm
*21.5mm
12mm
(+1mm) 35mm Dia.
Example
B(3x15mm)
Cross head
B(3x15mm)
TOP
TOP
Left hand hinged door
openingshown,
(righthandopposite).
*Check and drill
hole according to
the actual hole
drilling position of
door frontal range
being used.
www.howdens.com
5- Prepare the décor door
Ifrequired,thandlesatthisstage,
(screwsmayneedcountersinking).

7
REMOVE
CAP/END
max.
100mm
min
500mm min
300mm
max
1000mm
min
500mm
min
300mm
max
1000mm
www.howdens.com
Alldimensionsaretotheoor. DO NOT insertthehosetoodeepintothewastepipe,
(Maximum hose length, 3.2 metres).
6- Washing machine connections
WARNING!Thisappliance
mustbeearthed.
(Socket must be accessible
after tting).
Ensurecap/endisremovedfrom
wastepipespigot.
WARNING!Donotuseextension
cables/adapters.
Ensure water is turned on and
the isolator valve is accessible
after tting.
Hoseconnection-3/4”.
Coldwaterpressure-
0.1–1Mpa(0.3-1.0Bar)
NOTE: Ensure hoses are not
kinked or trapped behind the
washing machine.
NOTE: Ifnecessaryloosenand
rotate the water hose towards
thewatersupplyandre-tighten.
(Always use the new hose
supplied with the washing
machine).
Cold water supply
10-80 lpm.

8www.howdens.com
7 - Connect water hose (cold water supply only)
NOTE: Rotate the water hose
towardsthewatersupplyand
tighten.(Always use the
new hose supplied with the
washing machine).
Incorrectwastepipeconguration. Correctwastepipeconguration.

9
&
www.howdens.com
8- Positioning the washing machine
NOTE: Ensure hoses
are not kinked or
trapped behind the
washing machine.
DO NOT PUSH against the washing machine fascia panel.
DO NOT adjust the rear feet
until in nal position,
(NEVER move the washing
machine with the rear feet
extended).

10
A(4.5x10)
A(4.5x10)
x2
www.howdens.com
9- Fit décor door and magnetic catches