LaMotte Tracer 1749 User manual

Pool Professional's Meter!
Instrument de Mesure Professionnel pour Piscine!
TracerTM
Salt/EC/TDS PockeTester
Salinité/EC/TDS
Code 1749

WARNING! This set contains chemicals
that may be harmful if misused. Read
cautions on individual containers care-
fully. Not to be used by children except
under adult supervision.

3
INTRODUCTION
Congratulations on your purchase of the TRACER PockeTester. The
TRACER
offers direct reading of salinity, conductivity, and TDS with one
electrode. Careful use and maintenance
will provide years of reliable service.
SPECIFICATIONS
Display 2000 count LCD with Bar Graph
Conductivity Ranges 0 to 199.9 µS
200 to 1999 µS
2.00 to 19.99 mS
TDS Ranges
(Variable Ratio)
0 to 99.9 ppm or mg/L
100 to 999 ppm or mg/L
1.00 to 9.99 ppt or g/L
Salinity Ranges 0 to 99.9 ppm
100 to 999 ppm
1.0 to 9.99 ppt
TDS Ratio 0.4 to 1.0, adjustable
Salinity Ratio 0.4 to 0.6 automatic
Conductivity ATC 2.0% per °C
Temperature Range 32.0 to 149.0 °F, 0.0 to 65.0 °C
Temperature Resolution 0.1 up to 99.9, 1>100
Temperature Accuracy ±1.8°F, 1°C (from 32 to 122°F, 0 to 50°C)± 5.4°F,
3°C (from 122 to 194°F, 50 to 90°C)
Conductivity ATC Range 32.0°F to 140°F, (0.0°C to 60.0°C)
Accuracy Conductivity: ± 2% FS
TDS: ± 2% FS
Salinity: ± 2% FS
Measurement Storage 25 numbered readings
Low Battery Indication ‘BAT’ appears on the display
Power Four CR 2032 Lithium Ion batteries
Auto Power Off After 10 minutes of no button presses
Operating Conditions 23 to 122° F, –5 to 50° C
Dimensions 1.6 X 7.4 X 1.6 inches, 40 X 187 X 40 mm
Weight 3.1 oz, 87 g

4
CONTENTS
SAL/EC/TDS TRACER PockeTester Kit Code 1749
Includes: Salinity Standard, 3,000 ppm
Sample Cup w/cap †
Code 6005-G
† Not sold individually. See below.
PARTS & ACCESSORIES
SAL/EC/TDS Replacement Electrode Code 1765
Weighted Stand w/Sample Cups (5) Code 1746
Sample Cups w/caps (24) Code 1745
Conductivity Standard, 84 µS, 30 mL Code 6312-G
Conductivity Standard, 1413 µS, 30 mL Code 6354-G
Salinity Standard, 3,000 ppm, 30 mL Code 6005-G
*WARNING: Reagents marked with an * are considered to be potential health hazards. To
view or print a Safety Data Sheet (SDS) for these reagents go to www.lamotte.com.
Search for the four digit reagent code number listed on the reagent label, in the contents
list or in the test procedures. Omit any letter that follows or precedes the four digit code
number.
For example, if the code is 4450WT-H, search 4450. To obtain a printed copy, contact
LaMotte by email, phone or fax.
Emergency information for all LaMotte reagents is available from Chem-Tel: (US, 1-800-
255-3924) (International, call collect, 813-248-0585).

5
METER DESCRIPTION
Front Panel Description
1. Battery compartment cap
2. LCD Display
3. MODE button - change mode,
hold data, store data
4. CAL button - calibration, change
temperature units, recall data
5. ON/OFF button
6. Electrode Collar
7. Electrode
(Note: The Electrode cap is not shown)
TRACER Display
1. Bar graph display
2. Main display
3. Temperature display
4. Measurement units
5. Range calibration and
low battery indicators
6. Reading hold indicator
4
3
1
5
6
2
HML
0
0
2
10
20
12
5
10
7
BAT
mg/L
m
µS
t
m
pp
8.8.8.8
°C
°F
8.8.8
HOLD

6
BASIC OPERATION
Powering the TRACER
The Tracer uses four CR2032 Lithium Ion batteries. If the batteries are weak,
the BAT indicator will appear on the display. Press the ON/OFF key to turn
the TRACER on or off. The auto power off feature will shut the TRACER off
automatically after ten minutes of inactivity.
TDS Compensation Ratio
The TDS value is determined by multiplying the conductivity measurement
by a known conversion ratio factor. The meter allows the selection of a
conversion ratio factor in the range of 0.4 to 1.0. The selected ratio will vary
with application but is typically set between 0.5 and 0.7. In the salinity mode,
the ratio is fixed at 0.5. The stored ratio factor will briefly appear in the lower
temperature display when the meter is first turned on or when changing the
measurement function to TDS.
NOTE: In the salinity mode the ratio is 0.4 to 0.6 automatic.
To Change the TDS Conversion Ratio:
1. Turn the TRACER on.
2. Press and release the CAL button twice.
The stored ratio will appear in the display.
3. Press the MODE button to change the ratio
value in steps of 0.1.
4. When the desired ratio is displayed, press and
release the CAL button to store the value and
return to the normal mode.
5. If no buttons are pressed for 5 seconds, the
meter will return to the measurement mode.
0.7

7
Changing Temperature Units
To change the displayed temperature units between °F or °C:
1. With the TRACER off, press and hold the CAL button.
2. With the CAL button pressed, momentarily press the ON/OFF button.
When SELF CAL appears in the display, release the CAL button. The
TRACER will return to the operational mode with the temperature
displayed in the new units.
Data Hold
Press the MODE button to freeze the current reading. The HOLD icon will
appear, the reading will be stored. Press the MODE key to return to normal
operation.
Auto Power Off
The auto-power off feature will automatically shut the meter off 10 minutes
after the last button was pressed. To disable the auto-off feature:
1. Press the ON/OFF button to turn the meter on.
2. Wait for the SELF display screen to appear. This is the second screen
to appear after turning on the meter. IMPORTANT: Review the
instructions for the next 3 steps before proceeding. Step 3 must be
followed immediately by Step 4.
3. Press CAL button once quickly.
4. Press MODE and ON/OFF buttons simultaneously for approximately
two seconds. Quickly release buttons.
5. oFF will be displayed on the screen. Watch carefully. It will disappear
quickly.
6. The auto power off feature will be restored automatically when the
meter is turned off. Auto-off is the default function when the meter is
turned on.
Low Battery Indicator
The “BAT” indicator will be displayed when the batteries become weak. Refer
to the maintenance section for battery replacement information

8
TESTING
Getting Started
1. Remove the cap from the bottom of the TRACER to expose the
electrode.
2. Before the first use, rinse the electrode in deionized water and dry.
3. For best results, calibrate for conductivity with a standard in the
expected range of the sample. For maximum accuracy calibrate
from low conductivity
value standards to high conductivity value
standards.
4. Store dry.
Changing the Measurement Function
The meter can be set to measure Conductivity, TDS (ppm), TDS (mg/L) or
Salinity (ppm). To change the mode:
1. Turn the TRACER on.
2. Press and hold the MODE button for 2 seconds. The display will begin
to scroll through the units.
µS (Conductivity) | ppm (TDS) | mg/l (TDS) | ppm (Salinity “S”)
3. Release the MODE key when the desired mode is displayed.
4. Note that the “HOLD” function can not be on when changing
functions.

9
Measurement
1. Fill a sample cup to the 20 mL line with the test sample. Sample
depth must be greater than or equal to 1.5 inches.
2. Immerse the TRACER electrode in the sample. Make sure the
electrode is completely submersed.
3. Press the ON/OFF button. (8888 and then SELF
CAL will appear in the display during the initial
diagnostics).
4. Press and hold the MODE button to scroll to the
desired measurement mode.
5. Insert the electrode into the sample making
sure that the electrodes are completely
submerged.
6. Slowly stir the sample with the TRACER to
remove air bubbles.
7. The meter will autorange to the proper range and
the reading will be displayed.
8. Rinse the electrode in distilled water. Replace the
cap.
790

790

100.9

Measuring the TDS of Soil
1. Fill a 50 mL beaker with the soil sample.
Tap the beaker lightly on a hard surface
to remove trapped air. Remove excess
soil from the surface.
2. Empty the soil into a 250 mL wide-mouth
flask.
3. Add 100 mL of distilled water. Stopper
and shake vigorously.
4. Wait 30 minute. (Shake the flask
vigorously three or four times during this
period.)
SAL/EC/TDS
ON
OFF
MODE
CAL
100.9
72.3 ∞F
4.01

10
5. Filter the contents of the flask. Collect the filtrate in a beaker.
6. Rinse the electrode with distilled or deionized water to remove
impurities.
7. Press the ON/OFF button to turn the TRACER on. Make sure the meter
is in the TDS mode.
8. Immerse the electrode in the filtrate. Make sure the tip of the
electrode is completely immersed.
9. Stir the filtrate with the electrode to create a homogeneous solution.
10. Gently stir the filtrate with the electrode. Read the TDS value of the
filtrate from the display.
11. Rinse the electrode in distilled water. Replace the cap.
Storing Readings
1. After the reading is displayed press and hold
the MODE button to store the current reading.
The meter will enter the HOLD mode and HOLD
will be displayed. The storage location number
will be displayed on the lower display followed
by the reading being stored.
2. Press the MODE button to exit the HOLD mode
and return to normal operation.
3. If an attempt is made to store more than
25 readings,
the stored readings will be
overwritten starting with the first reading.
Recalling Stored Readings
NOTE: First ensure that the HOLD symbol is not displayed. If it is, exit the HOLD
function by pressing the MODE button.
1. Press the CAL button and then press the MODE button; the location
number (1 through 25) will briefly appear and then the value
stored
in that location will appear. The displayed units will flash, indicating
that the storage recall mode is active.
L
1423
72.3 ∫F
20
2
2
10
20
15
s
10

11
2. The last stored reading taken will be displayed first. To advance to
the
previously stored readings, press the MODE button. The location
number
is displayed first, followed by the reading stored in that location.
3. To exit the storage mode, press the CAL button and the TRACER will
return to normal operation after displaying “End”.
Clearing the Stored Memory
Turn the TRACER on. Press and hold the ON/OFF button for 4 seconds. The
display
will briefly display “clr” when the memory is cleared.
CALIBRATION
For the most accurate results, allow sufficient time for the temperature of
the probe to reach the temperature of the sample before calibrating. This
will be indicated by a stable temperature reading on the display
Meter accuracy verification should be performed on a periodic basis as
needed. If calibration is required, the meter must be in the salinity mode
to perform a calibration for salinity, or in the conductivity mode to perform
calibrations for conductivity, and TDS. The meter can perform a calibration
and store the data for one range in the salinity mode and each of the three
ranges – low, medium and high for the conductivity and TDS modes. The
automatic calibration recognition procedure will recognize salinity standard
3,000 ppm (medium) and conductivity standards of 84 µS (Low), 1413 µS
(Medium) or 12,880 µS (12.88 µS) (High). (See Page 5). Always calibrate in
the range closest to the expected measurement value. For salinity samples
within the range of 1,000 to 9,999 ppm salinity, calibrate with a 3,000 ppm
calibration standard.
1. Fill a sample cup to 20 mL line with a calibration standard.
NOTE: The meter allows for a 1, 2, or 3 point calibration for conductivity
and TDS. If calibration is done for more than one point, the lowest
concentration should be done first to obtain the best accuracy.
Calibrate the ranges from low to high
2. Press the ON/OFF button to turn the TRACER on. Insert the electrode
into the standard. Tap or stir the sample with the Tracer to dislodge air
bubbles.
3. Press and hold the CAL button for approximately 2 seconds. “CAL” will
appear and the display will flash.
4. The meter will automatically recognize and calibrate to the calibration
standard. The display will briefly indicate “SA” and “End” and then return
to the measurement mode.
NOTE: “SA” will not appear if the calibration fails.

12
5. The calibration range indicator will appear on the display for each range
that is calibrated during a power on cycle.
L
Low Range, 84μS/cm
M
Medium Range, 1413μS/cm or 3000 ppm SaH
H
High Range, 12,88mS/cm (12,880μS/cm)
NOTE: Each time the calibration mode is entered all calibration range
indicator
s will be cleared, but only the calibration data for the currently
selected range will
be replaced. In the conductivity/TDS modes, the
calibrations for the other two ranges will be saved even though the
indicators for those ranges are no longer displayed. Calibration of all
three ranges must be performed during one power on period for all three
calibration range indicators to be displayed.
Reset Calibration Data
Follow this procedure to clear all calibration data from the meter. Resetting
the calibration data may be necessary when new calibration solutions are
used or accuracy of measurements is in question.
1. Turn off the meter.
2. Press and hold the CAL and MODE buttons.
3. Momentarily press the ON/OFF button, as soon as they display comes
on, release all 3 buttons.
4. The display will show “dFLt rSt” (default restart) and all of the
calibration data will be erased. If “dFLt rSt” does not appear, retry the
procedure.
5. Proceed to the calibration routine for pH and Conductivity.

13
OPERATIONAL MATRIX
Function/
Resulting Action Power Mode
Key Press Sequence
On/Off On or Off Any Momentary press of ON/
OFF button
Calibration On Con Press & hold CAL button
for 2 seconds until CAL is
displayed
Store Reading On Any Momentary press of MODE
button
Hold Release On Hold Momentary press of MODE
button
Enter Memory
Retrieval
On Any Momentary press of CAL
button followed by a
momentary press of MODE
button within 4 seconds.
Scroll Stored
Readings
On Memory
Recall
Momentary press of MODE
button Displays last in first
out.
Exit Memory Retrieval On Memory
Recall
Momentary press of CAL
button
Clear Stored Memory On Any
Measure
Mode
Press and hold the ON/OFF
button for 4 seconds until
“clr” is displayed.
Change Measurement
Mode
On Any Press and hold MODE
button for 2 seconds.
Modes will scroll by until
button is released
Enter CON/TDS Ratio On TDS (ppm
or mg/L)
Press and release the
CAL button twice in quick
succession.
Change CON/TDS
Ratio
On TDS (ppm
or mg/L)
Momentary press of
MODE button. Each press
increases ratio by 0.1 from
0.4 to 1.0.
Exit CON/TDS Ratio On TDS (ppm
or mg/L)
Momentary press of CAL
button.

14
Change Temperature
Units
On (off mode) Press and hold CAL button
then momentarily press
ON/OFF button. Release
CAL button after“Self Cal”
is displayed.
Override Auto Power
Off
On Any Momentarily press
CAL button then
simultaneously press
and hold CAL and MODE
buttons for 2 seconds until
“oFF” is displayed.
Default Reset Off n/a Simultaneously press
ON/OFF, CAL and MODE
buttons momentarily.
“dFlt” will be displayed.
MAINTENANCE
Storage
1. Do not touch the inner surfaces of conductivity electrodes. Touching
the surface of the platinized electrodes may damage and reduce the life
of the probe.
2. Store the electrode dry with the cap on.
3. Always rinse the electrode in deionized water between measurements
to avoid cross contamination. Double rinsing is recommended when
high accuracy is required.
Battery Replacement
1. Twist off the battery compartment cap.
2. Hold the battery housing in place with one finger. Remove the battery
carrier by pulling on the small tabs.
3. Replace the four CR2032 batteries. Observe polarity.
4. Replace the battery compartment cap.

15
Never dispose of used batteries or rechargeable batteries in
household waste. As consumers, users are legally required
to take used batteries to appropriate collection sites, the
retail store where the batteries were purchased, or wherever
batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The user is
obligated to take end-of-life devices to a designated collection point for the
disposal of electrical and electronic equipment.
Replacing the electrode
1. Unscrew and remove the electrode collar. Turn collar counter-clockwise.
2. Gently rock the electrode side to side, while pulling it away from the
meter, until it disconnects from the electrode socket.
3. To attach an electrode, align the slots and carefully plug the electrode
into the meter socket. CAUTION: Take care to align pins carefully. Bent or
broken pins will cause the meter to malfunction.
4. Firmly tighten the electrode collar to create a seal with the rubber
gasket between the electrode and the meter.

16
Electrode Cleaning Recommendations
Do not soak the electrode in the solutions for longer than the recommended
length of time. To do so may cause a reference potential shift which will
cause a degradation in performance or failure. When cleaning the probe, do
not scratch or damage the platinized electrode surfaces.
Contaminant Cleaning Solution Procedure
Water soluble
substances
Deionized water Soak or scrub with a soft brush.
Rinse thoroughly with DI water
and dry.
Grease and oil Warm water and
household detergant
Soak or scrub with a soft brush,
maximun 10 minutes. Rinse
thoroughly with DI water and
dry.
Heavy grease Alcohol Soak for a maximum of 5
minutes. Scrub with a soft
brush. Rinse thoroughly with DI
water and dry.
Lime and
hydroxide
coatings and oil
10% Acetic acid Soak until coating dissolves,
maximum 5 minutes. Rinse
thoroughly with DI water and
dry.

17
TROUBLESHOOTING
Problem Check Action
Reading is frozen HOLD mode Press MODE button to exit
HOLD mode
“BAT” message Batteries low Replace batteries
Meter will not calibrate Trapped air
bubbles
Tap probe or stir sample to
release air bubbles
Dirty probe Clean probe
Damaged probe Replace probe
Contaminated
standards
Use fresh standards
Meter will not turn on Batteries low or
dead
Replace batteries
Battery polarity Replace batteries with correct
polarity
Unit will not respond to
any key presses
Internal fault Perform hard reboot. Remove
batteries, hold ON/OFF button
down for 5 seconds, replace
batteries
“_oL_” message Sample is out of
range
Dilute sample

18
WARRANTY
LaMotte Company warrants this instrument to be free of defects in parts
and workmanship for 1 year from the date of shipment and the probe
to be free of defects in parts and workmanship for 6 months from the
date of shipment. If it should become necessary to return the instrument
for service during or beyond
the warranty period, contact our Technical
Service Department at 1-800-344-3100
or [e-mail] for a return
authorization number or visit www.lamotte.com
for troubleshooting help.
The sender is responsible for shipping charges, freight,
insurance and
proper packaging to prevent damage in transit. This warranty does
not apply to defects resulting from action of the user such as misuse,
improper wiring, operation outside of specification, improper maintenance
or repair, or
unauthorized modification. LaMotte Company specifically
disclaims any implied
warranties or merchantability or fitness for a
specific purpose and will not be liable for any direct, indirect, incidental or
consequential damages. LaMotte Company’s total liability is limited to repair
or replacement of the product. The warranty set forth above is inclusive and
no other warranty, whether written or oral, is expressed or implied.
To register your meter with the LaMotte Service Department —
go to www.lamotte.com and choose SUPPORT on the top navigation bar.

19
INTRODUCTION
Félicitations pour votre acquisition du mesureur de TRACER PockeTester.
Avec la technologie dynamique à constante de cellule électrolytique du
TRACER, il est possible de mesurer une large gamme de Conductivité, TDS
et Salinité avec la même électrode. Cet appareil peut être utilisé pendant
plusieurs années s’il est manié avec précaution.
AVERTISSEMENT ! Ce kit contient des
produits chimiques qui peuvent être no-
cifs s’ils sont utilisés de façon impropre.
Lisez avec attention les avertissements
sur chaque récipient. Ce produit n’est
pas destiné à être utilisé par des enfants,
sauf sous la surveillance d’un adulte.

20
CARACTÉRISTIQUES TECHNIQUES
Affichage LCD avec 2000 impulsions d’affichage et
diagramme en barres
Gammes de conductivité 0 à 199,9μS/cm
200 à 1999μS/cm
2,00 à 19,99mS/cm
Gammes TDS
(Ratio variable)
0 à 99.9ppm ou mg/L
100 à 999ppm ou mg/L
1.00 à 9.99ppt ou g/L
Gamme de salinité 0 à 99.9ppm
100 à 999ppm
1.00 à 9.99ppt
Taux TDS réglable de 0,4 à 1,0
Taux de Salinité 0,4 à 0,6 automatique
ATC de Conductivité 2,0% par °C
Gamme de température 0,0°C à 65,0°C (32,0°F à 149°F)
Résolution de
Température
0,1 à 99,9, 1 >100
Précision de la
Température
±1°C; -16,78°C (de 0 à 50°C; 32 à 50,00°F)
±3°C; -14,78°C (de 50 à 65°C; 122 à 149,0°F)
Gamme ATC de
Conductivité
0,0°C à 60,0°C (32,0°F à 140°F)
Précision Conductivité : ±2% déviation maximale
TDS: ±2% déviation maximale
Salinité : ±2% déviation maximale
Mémoire de mesure 25 lecture marquées (numérotées)
Indication piles faibles ‘BAT’ apparaît sur l’écran
Marche/Arrêt Quatre (4) piles lithium ion CR2032
Arrêt automatique Après 10 minutes (remplacement disponible)
Conditions de
fonctionnement
-5°C à 50°C (23°F à 122°F)
Dimensions 40 x 187 x 40 mm (1,6 x 7,4 x 1,6”)
Poids 87 g (87,88 g)