Lampo FLOOD 1000W User manual

F
F
FL
L
LO
O
OO
O
OD
D
D
1
1
10
0
00
0
00
0
0W
W
W
H
H
Ha
a
al
l
lo
o
og
g
ge
e
en
n
n
f
f
fl
l
lo
o
oo
o
od
d
dl
l
li
i
ig
g
gh
h
ht
t
t
USER’ S MANUAL release 1.0
This manual must be considered an integral part of the projector.

1
This instruction manual contains important information about the installation and use of the
projector. Please read and follow these instruction carefully.
Always ensure that the power to the projector is disconnected before opening the projector or
commencing any maintenance work.
The specifications can be changed in the course of product improvement.
SAFE USAGE OF THE PROJECTOR
• Do not attempt to dismantle and modify the projector.
• Do not allow contact with water or any other fluids, or metallic objects (IP20).
• Do not install the projector in areas of high humidity.
• The projector is not designed or intended to be mounted directly on to inflammable
surfaces.
• Keep at least 0.5m distance between the projector and adjacent inflammable surfaces.
• Keep at least 3m between the lamp and the illuminated surfaces.
• The projector must only be used complete with its protective grill and/or front lens.
• Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
• Note: the lamp reaches very high temperatures, allow at least 15 minutes for the lamp to cool
completely before attempting to handle it. Ensure the lamp is cool before attempting to handle it
INSTALLING THE PROJECTOR
The projector should be mounted through the 10mm hole in its bracket (1). For safety the projector
should have a secondary fixing with a safety chain through the fixing eye (3). The projector bracket
allows an angle adjustment of +90° / -90° and, once positioned, the knob (2) should be firmly tightened.
The projector mounting bracket can also be easily rotated to be positioned on the underside of the
projector for tripod mounting.
FITTING THE LAMP
The lamp access hatch is released by turning the screw (4). Open the protective grill and insert the lamp
into the sockets. use only the lamp version that is correct for the mains voltage. Insert the lamp with care
and without using excessive force, use a cloth to hold the lamp and do not touch the glass of the lamp
directly with your hands.
Replace the protective grill and close the access hatch
Linear halogen lamp 1000W R7s (185.7mm) horizontal LP15

2
POWER SUPPLY - MAINS
The projector comes with a 2m cable. It’s necessary to mounting a suitable plug and correctly earthed.
BROWN = LINE BLUE = NEUTRAL YELLOW / GREEN = EARTH
FILTER FRAME
The filter frame (5) is located to the front of the projector. Slide the filter frame out. Insert the coloured
gel, replace when the gel is inserted.
It is recommended that only filters with a high temperature capacity are used.
MAINTENANCE
If the protective grill or any of the lenses become damaged or broken they should be replaced. If the
lamp becomes damaged or deformed in any way it must be replaced. To ensure the reliability of the
projector it should be kept clean. It is recommended that the lenses should be regularly cleaned (six
months) to maintain an optimum light output. Do NOT use any type of solvent on filters and lenses.
MODULAR SYSTEM ASSEMBLY
It is possible to have a multiple light source by connecting two or tree projectors together. You could
have the accessory to connect the projectors, on request.
One accessory TE134 for two projectors and two accessories TE134 for tree projectors.
TE134 is made by two clamps with 8 fixing screws.
Unscrew the knob (2) and fix the bracket of one floodlight on
the other side.
Fix the first clamp with the 4 screws where are two
floodlights meet. Do the some thing whit the second clamp
on the bottom part of the floodlights.
Unscrew the knob (2) and fix the bracket of
one floodlight on the other side. Take away
the bracket on another floodlight.
Fix the first two clamps with the screws
where the floodlights meet. Do the some
thing whit the other 2 clamps on the bottom
part of the floodlights.