Lan Castle 90204 User manual

OPERATION INSTRUCTION
Villa Wireless color high definition
video intercom system
+

1 2
Name Descriptions
IR LED Provides illumination with IR LEDs for better night vision
Camera sensor Capture image and transmit it to display
LED indicator Work status indication
Power LED Power status indication
Speaker Sound from outdoor camera
Switch Turn on/off the power supply of indoor monitor
TFT display 2.5inch display, resolution:480X3(RGB)X234
The shortcut key to enable video-record mode / internal
communication mode
Unlock Release the door lock by pressing this button
Monitoring Monitor and surveillance outside status
Start Conversation with outdoor camera
Microphone Transmit indoor voice to outdoor camera
Shortcut key to enable picture capture mode
USB interface Rechargeable port via a external USB cable
123456
FEATURES
OUTDOOR CAMERA
Installation bracket Affix and protect the outdoor camera from rain/snow
Microphone Transmit outdoor voice to indoor monitor
Call button Call indoor monitor for intercommunication
Speaker Sound from indoor monitor
Terminal Connect to power supply and door lock
Antenna Transmit high frequency wirelessdata
+
Talking
1
2
3
4
5
6
7
8
9
NO
Reset button
INDOOR MONITOR
NO
1
2
3
4
5
6
7
8
9
10
11
12
Name Descriptions
Initialize outdoor camera

Digital RF IC can synchronously transmit video and audio data
Adopts Ov7725 camera 2.4 inch TFT dispaly with high definition
MJPEG video compressed format , max.10~16fps unilateral transmission
Adopts 2.4G ISM digital common channel :2402~2483.5MHz
Max. 2Mbps wireless data rate transmission
16-digital voice sampling precision ,8K sampling rate, DAC port with 16-digital audio output
Full-duplex audio communication mode
Transmission power 16-20dBm, receiving power -90~-100dBm
Transmission distance:100m(line of sight)
Indoor monitor provided with DC 3.7V , outdoor camera provided with DC5V,1000MA
Adopts AFH intelligent frequency hopping and can synchronously share 2.4GHz channel with
other device e.g. WLAN, Bluetooth, microwave oven, cordless phone etc.
Random configure both of communication and synchronization channel
turn on/off
In the power off state ,the highlighted[Welcome] will appear on the
background whilst press and hold the button(shown in the picture
on the left), release this button until two brief tones with Di-Di- will
be heard .
In the standby mode ,the highlighted [Goodbye] will appear on the
background whilst press and hold the button(shown in the picture
on the left), release this button until a brief tone with Di will be heard .
Operation temperature:-30 -+50
SPECIFICATIONS OPERATIONS
+
STANDBY MODE
1
12:54
2009\06\18 Thu
ab
c
d
In the standby mode ,indoor unit will display a standby picture
as the left .
aRF signal intensity indication
bOwn ID number
c
Li battery capacity indication
d
Time ,Date and Week
Please note that the system will go into the dark screen savers in
10s of time span without any button is pressed until you press the
button to relight the screen again , meanwhile the power LED
is slowly flashing red.
Menu operation
In menu mode, the system will go into the dark screen savers in 10s of time span without any button
is pressed until you press any of buttons to relight the screen again; Pressing the button any time
will exit the present menu and return to the previous menu.
In standby mode, pressing the button to enable the menu mode.
A. Video
Press the
button
Video
Press the
button
M091026141524
Video Press the
button
M100619111117
Option
Play
Delete
Back
Press the
button
This function is used to playback the stored video
Waiting..... Press the
button
to
replay
Press the
button
Option
Play
Delete
Back
If you need to delete this video, please select [Delete] and press the button , then select [Yes]
and press the button to confirm. To return to the previous menu, you can also select [Back]
and press the button .
Press the
button
M091026141524
Video
M100619111117
Press the
button
Video
Standby mode
e
e
Power LED
34

B. Album
Press the
button
Album
Press the
button
P100611143657
Photo Press the
button
P100611143659
Option
View
Delete
Back
Press the
button
This function is used to view the stored pictures.
If you need to delete this picture, please select [Delete] and press the button , then select [Yes]
and press the button to confirm. To return to the previous menu, you can also select [Back]
and press the button .
Press the
button
Press the
button
Press the
button
or
Press the
button
Option
Play
Delete
Back
P100611143657
Photo
P100611143659
Album
C.Setting
Press the
button
Setting
Press the
button
Tone setup
Brightness
Own ID number
Autocontrol
Setting
C1.Tone setup
Flash setup
Date setup
Press the
button
Tone setup
Romance
Beauty and the
Memories
Titanic
Love music box
Near ToYou
This function allows you to select any of melodies as a ringing tone, built-in up to 12 melodies are
selectable: Romance
Beauty and the Beast
Memories
Titanic
Love Music Box
Near To You
Green sleeves
Whisper in Autumn
For Elise
Rhythm Of The Rain
Love Is Blue
Romeo and Juliet
Press the
button
or
Tone setup
Romance
Memories
Titanic
Love music box
Near ToYou
Beauty and the
Tone setup
Romance
Memories
Titanic
Love music box
Near ToYou
Beauty and the
Press the
button
Press the
button
Tone setup
Brightness
Own ID number
Autocontrol
Setting
Flash setup
Date setup
If you select the favourite tone, pressing the button will start to play the melody .
C2.Brightness
Press the
button
or
Tone setup
Own ID number
Autocontrol
Setting
Flash setup
Date setup
Press the
button
Brightness
Brightness Brightness
It is useless to press the button if the brightness of TFT display reaches to Min. Value or Max. Value.
Press the
button
or
C3.Own ID number
Tone setup
Autocontrol
Setting
Flash setup
Date setup
Press the
button
Brightness
Own ID number
Own ID number Number 1
Own ID number
Number 2
This system allows up to 3 video indoor monitors to connect with 1 outdoor camera, therefore each
indoor monitor needs to program the different ID number respectively, otherwise the same ID number
maybe result in some unknown malfunctions.
Press the
button
Tone setup
Autocontrol
Setting
Flash setup
Date setup
Brightness
Own ID number
Press the
button
or
Press the
button
or
Press the
button
Tone setup
Own ID number
Autocontrol
Setting
Flash setup
Date setup
Brightness
C4. Autocontrol
Tone setup
Brightness
Own ID number
Setting
Flash setup
Date setup
Press the
button
Autocontrol
Auto video
Manual video
Autocontrol
Press the
button
or
Press the
button
Tone setup
Brightness
Own ID number
Setting
Flash setup
Date setup
Autocontrol
C4.1.Auto Video record
If the Auto video record mode is selected, when the call button is pressed on the outdoor
camera, and then your indoor unit will sound melodies meanwhile the visitor's image will display
on the screen, in the upper left of the screen, an superimposed icon indicates that a real time
video record is underway.
This function allows a real time video is to be automatic recorded in case you are not at home.
Please note that only the indoor unit which is programmed as ID number 1 can be allowed to select
Auto video record mode
56

Tone setup
Brightness
Own ID number
Setting
Autocontrol
Press the
button
or
Press the
button
Time and Date
Time:13:06
Flash setup
Press the
button
or
Date setup
Press the
button
Tone setup
Brightness
Own ID number
Setting
Autocontrol
Flash setup
Date setup
Date:2010\06\19 sat
Time and Date
Time:23:06
Date:2010\06\19 sat
Time and Date
Time:23:06
Date:2010\06\19 sat
Press the
button
In the process of Time and Date, if you need to select the next item, please press the button
to move the rectangle frame, press either of the button or to change the target value.
Press the
button
Setting
Press the
button
Tone setup
Brightness
Own ID number
Setting
Flash setup
Date setup
Autocontrol
Press the
button
or
Autocontrol
Auto video
Tone setup
Brightness
Own ID number
Setting
Flash setup
Date setup
Press the
button
Autocontrol
Auto video
Manual video
Autocontrol
Manual video
Press the
button
or
C4.2.Manual video record
If the manual video record mode is selected, when the call button is pressed on the outdoor
camera, and then your indoor unit will sound melody meanwhile the visitor's image will display
on the screen, press the button to start conversation with visitor, and then press the button
to enable video record, in the upper left of the screen, an superimposed icon indicates that a
real time video record is underway; pressing the button will end video record.
Tone setup
Brightness
Own ID number
Setting
Date setup
Autocontrol
Press the
button
or
C5. Flash setup
Press the
button
Flash interval
Second:10
Flash setup
Press the
button
or
Flash interval
Second:20
Press the
button
Tone setup
Brightness
Own ID number
Setting
Date setup
Autocontrol
Flash setup
This function is used to adjust the time span that start screen savers every time.
C6. Date setup
D.Code
In the process of menu mode, to pair code both of the outdoor camera and indoor monitor, please
follow these steps as below:
Step 1:
Press and hold
the call button
on the outdoor
unit
LED is flashing
across and a
rapid tone is
heard outside
LED is lighting
red, a rapid
tone is heard
outside
Press the
reset button
on outdoor
unit(page 1)
D1.Pair code(Notice: Please don't pair code unless necessary)
Press the
button
Code
Press the
button Match code
Give code
Receive code
Clear code
Code
Step 2:
Step 3:
Success
Code
Press the
button
or
Match code
Give code
Receive code
Clear code
Code
Press the
button
Clear code
Clear
Back Press the
button
Are you sure
to clear code?
YES
NO
Match code
Give code
Receive code
Clear code
Code
Press the
button
or
Press the
button
Match code
Press the
button
Code
Press the
button Match code
Give code
Receive code
Clear code
Code Press the
button
or
Match code
Receive code
Clear code
Code
Press the
button
Give code
D2.Give code(indoor unit that has already been paired code)
Give code
If the highlighted [success] appeared on the screen, it means that the paired code is successful
both of the indoor monitor and outdoor unit. If the highlighted [failed] appeared, that means that
it is to fail to pair code, please retry the step as above.
Match code
Give code
Receive code
Clear code
Code
Press the
button
78

Code
Give code
Receive code
Clear code Clear code
Press the
button
Receive code
Give code
Receive code
If the the highlighted [success] appeared on the screen, it means that receive codeis successful
both of two indoor monitors. If the highlighted [failed] appeared, that means that it is to fail to
receive code, please retry the step as above.
D3.Receive code(another indoor unit that is not paired code)
Code Code
Press the
button
Press the
button
Press the
button
or
Match code Match code
VISITOR CALL
Standby mode
The Visitor press
the call button on
the outdoor
camera
A continuous
melody ringing
is heard inside
The visitor's image
automatically
displayed on the
screen
Sounds a continuous beep,
with the red LED indicator is
on(marked as on page 1) .
Press the talking
button on
the indoor
monitor
Press the button
on the
indoor
monitor
Start
conversation
Press the button
on the
indoor
monitor
Manual-record a
video
Manual-capture a
picture
The red LED indicator on the
upper right corner will change
to green(marked as on page 2)
Conversation
duration is up
to 120 seconds
at a time
Press the unlock
button on indoor
monitor
Press the talking
button
again
An icon are
superimposed
on the screen
Please be aware that the outdoor camera will return to standby mode with 4 brief tones if indoor
unit failed to response within 4 seconds.
Please note that if the indoor monitor is in the recharging status, it will affect the quality of
communication, please make sure to pull out the USB cable before using this device.
Automatically switch
off the display and
conversation
Function-key operation
MONITORING
Standby mode
Press the monitoring
button on the
indoor monitor
Activate both view
of the image and
conversation with
the outdoor camera
the monitoring
duration is 60
second.
Press the button
on the
indoor
monitor
Press the button
on the
indoor
monitor
Manual-record a
video
Manual-capture a
picture
The red LED indicator on the
upper right corner will change
to green(marked as on page 2)
Press the monitoring
button again
End
This function is to view the image at entrance
910

INTERNAL COMMUNICATION
Standby mode
The system supports up to 3 indoor units are connected with 1 outdoor camera, therefore this
function is required at least 2 indoor units for intercommunication among internal indoor unit.
Press the button
on the indoor
monitor
A continuous
melody ringing
is heard
Press the talking
button on
the indoor
monitor
User ID number
2
1
2
Calling...... Press the talking
button on
2 # indoor
monitor
Start internal
conversation
If the highlighted [user not online] appeared on the screen, it means that the indoor unit that you
called can not be connected, please double check that the indoor units are in the working condition.
The internal conversationduration is up to 120 seconds at a time
Factory default : unlock time is set for 1.8s. please follow these steps as below:
press and hold the call button on outdoor camera whilst plug into power, a brief tone will be heard
in the meantime the red LED indicator is on , release the call button and a brief tone indicates
success of setting.
Unlock Relay Output Pulse
The dry contact is kept under active or inactive condition if the unlock button is pressed on indoor
monitor, withActive 1 duration is 600ms,Inactive 1 duration is 400ms and Active 2 duration is
800ms.
Active 1 Active 2
Inactive Inactive 1 Inactive
Active
Secondly mode : unlock time is set for 4s.
press and hold the call button on outdoor camera whilst plug into power, a brief tone will be heard
in the meantime the red LED indicator is on, release the call button until 2 brief tones will be heard
and last a brief tone indicates success of setting.
Inactive Inactive
The dry contact is kept under active or inactive condition if the unlock button is pressed on indoor
monitor, with active duration is 4s.
Thirdly mode : unlock time is set for 8s.
press and hold the call button on outdoor camera whilst plug into power, a brief tone will be heard
in the meantime the red LED indicator is on ,then 2 brief tones continue, release the call button
until 3 brief tones will be heard and last a brief tone indicates success of setting.
Active
The dry contact is kept under active or inactive condition if the unlock button is pressed on indoor
monitor, with active duration is 8s.
Inactive Inactive
Output:4s
Output:8s
UNLOCK TIME SETTING ON OUTDOOR CAMERA
12
11

+
USB interface
Electric lock
Magnetic lock
Power supply
(not included)
Please check the connection of electric lock or magnetic
lock ,otherwise it will damage the device .
123456
DC5V
NC
COM
NO
SYSTEM CONNECTION INSTALLATION PROCESS OF OUTDOOR UNITS
NOTE:
Avoid installation of the device near strong radiation e.g.AC motor and lift .
Select the most suitable position where the camera is located at the user's eye sight
Switch off power supply before installation.
Keep more than 30cm away from AC power supply to avoid external interference.
Keep it away from the water and magnetic field.
Do not exposethe outdoor camera under strong lightor sunshine.
Maintenance should be complied with qualified technician .
Avoid hard shake , beating and collision ,otherwise the internal exact components maybe be
damaged .
Do not install the outdoor camera in the environment e.g. direct sunlight, contact rain, high
temperature, high humidity, full of dust and chemistry corrosive.
To install the outdoor unit, please follow these steps as below:
Hatch
Plastic anchor
Connection cable
Power adapter
Power adapter
AC100V~240V/
50~60Hz
1413
Unlock button

Federal Communications Commission (FCC) Statement
This equipment has been tested. And it found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates and uses and radiates radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
-Consult the dealer or an experienced radio /TV technician for help.
Warning: A shielded-type power cord is required in order to meet FCC emission limits
and also to prevent interference to the nearby radio and television reception.
It is essential that only the supplied power cord be used.
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
3. RF exposure warning:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
15