L&s Tilt n store User manual

6230 McKinley St. NW

Suite E

Ramsey, MN 55442

651-777-1554

www.LiftNStore.com

Space, Safety and Security Solutions

Tilt N Store Installation Manual

Unique patented Design Creates Space and Improves Security

Tilt N Store Installation Manual



Tilt N Store Installation Manual



Table of Contents

What is the Tilt N Store?____________________________________________________________________________ pg. 2

Safety Features _______________________________________________________________________________________ pg. 2

Tools Needed For Installation ________________________________________________________________________________ pg. 3

Safety Warnings __________________________________________________________________________________________________ pg. 3 - 4

Tilt N Store Bike Lift Diagram _______________________________________________________________________ pg. 4

Electrical Requirement ____________________________________________________ pg. 4

Frame Installation Instructions ______________________________________________________________________________ pg. 5 - 10

Troubleshooting __________________________________________________________________________________________________ pg. 10

Maintenance ____________________________________________________________ pg. 10

Warrenty ____________________________________________________________________________________________________________ pg. 11 - 12

Claim Form _________________________________________________________________________________________________________ pg. 13

Other Products ___________________________________________________________________________________________________ pg. 14 - 16

Disclaimer __________________________________________________________________________________________________________ pg. 17

Page 1

Tilt N Store Installation Manual

What Is the Tilt N Store?

●The Tilt N Store



is a versatile wall mounted storage

lift driven by an electric motor or hand crank.

●Can be used for the storage of clothing, bikes, and

more.

●Merchandise is securely and safely out of the way.

Safety Features

1. The gearbox and motor features a motor break that prevents

the machine from coasting and free falling.

2. The machine also features a seat belt re-tracker that will catch

the load and preventing the machine from going into free fall.

3. Machine also features a safety siren that allows people to hear

when it is in motion.

Page 2

Tilt N Store Installation Manual

Tools Needed for Installation

●Safety Glasses

●Work Gloves

●Reflective Safety Vest

●Caution Tape and Safety Cones

●25-foot Tape Measure

●Cordless Impact Drill

●3/8” Socket Drive

●15/16” Wrenches or

Ratchet/socket combo (2)

●5/16” Wrench

●4.5mm Allen Wrench

●4mm Allen Wrench

●3.5mm Allen Wrench

●T30 Star Drive

●2-foot (minimum) long level

Safety Warnings

●Do not exceed maximum rated weight limit of 300 lbs.

●Keep areas under the Tilt N Store



clear and open when operating. Do not allow people to walk under the

Tilt N Store



while it is running. Use of traffic cones or barricades may be required when using the Tilt N

Store



●Always watch the Hang Bar when raising or lowering.

●Do not climb on, hang from, or play on any part of the Tilt N Store



. This machine is designed to hold

merchandise only, not humans.

●Keep all controls away from children.

●The Tilt N Store



safety systems are not to be bypassed or circumvented. The purchaser is responsible for

purchasing the Tilt N Store



with applicable safety features required by their given area and fulfills their

particular needs.

●Any repair or adjustment must be performed by qualified maintenance personnel.

Page 3

Tilt N Store Installation Manual

●Before any repair or adjustment are made all hanging items or loads must be removed.

●When not in use, the Hang Bar should be left in the full 'UP' position. This will prevent people from

bumping into the hanging goods.

●If you hear a snapping sound and see jerking, STOP the Tilt N Store



immediately. Cut power and call

maintenance.

●Failure to follow safety and operational rules will void all warranties.

Tilt N Store Bike Lift Diagram

Electrical Requirement

The Tilt N Store



requires 120 Volts, 60Hz and 12 gage wire with a 20 Amp Breaker to safely operate.

Page 4

Tilt N Store Installation Manual

Frame Installation Instructions

The following steps below provide you with the instructions necessary to complete the Tilt N Store

installation.

➢Determining which type of Screw to use

Cement Walls:

Install 2x6 ledger board on the top and bottom where the

mounting bracket will attach using Tapcon screws



Wooden Stud Walls:

Install 2x6 ledger board on the top and bottom where the

mounting bracket will attach using



lag screws



Metal Walls:

Install 2x6 ledger board on the top and bottom where the

mounting bracket will attach using 1/4“ - 14x4” tek screws



➢Snap Line

The snap line will mark where the bottom of the

Tilt N Store



Frame will be. For normal setups your snap line

should be at a predetermined height. Your actual height may be

different.

➢Space Between Machines

Leave a one inch open space between every Tilt N Store



frame.

Note: If you are mounting several in a row, you will probably

want to use long 2x6 boards instead of several shorter boards.

Special note: If you ever intend to change these units over to use

4 or 6 foot hangbars, you will want to leave 13 inches between

each unit.

Page 5

Tilt N Store Installation Manual

➢Mounting 2x6 Ledger Board to Stud Wall

Important: Make sure you check with your construction expert

to make sure you mounting to a wall of high quality.

1. Use a stud finder to locate the studs you will be

mounting to.

2. Mark each 2x6 for drilling. Use 8 lag bolts along with 8 flat

washers to mount every 2x6.

3. Counter sink the holes big enough for the flat washers and

deep enough to contain the bolt heads.

Note: Please see the section titled “determining which type of

screw to use” if you are installing the Tilt N Store on a different

style wall.

How to mount the lower 2x6:

Your snap line should be 72 inches off the floor. Use this snap

line for the lower edge of your lower 2x6.

How to mount the upper 2x6:

Measure up 48 inches to get your second snap line. This snap

line will be for the top edge of the upper 2x6.

The TiltNStore Frame will mount flush with the bottom



edge of

this 2x6.

Note: Use your level to make sure you are mounting the 2x6

ledger board straight and level.

➢Placing the Mounting Brackets on the top 2x6

Place the mounting bracket level and 2.5 inches in from the end

of the 2x6 with the mounting bracket top held flush



to the top

of the 2x6 ledger board.

For each bracket, use 4 equally spaced hex head lag bolts to

secure the mounting brackets level and to the ledger board.

Page 6

Tilt N Store Installation Manual

➢Hanging the Tilt N Store

Once the mounting brackets are securely fashioned to the top

and bottom ledger boards, lift the Tilt N Store



above the

mounting brackets and slide the frame down until it catches on

the brackets. The tongue of the Mounting Brackets can be

placed in any of the cut out positions on the frame to allow easy

placement of each Tilt N Store



Once the mounting bracket tongue is placed in the desired

location on the Tilt N Store



, Secure the Tilt N Store



to the ledger

board using 4 hex head lag bolts for the top and 4 hex head lag

bolts for the bottom.

Note: Ensure that the Tilt N Store is level when installed.

➢Installing the Motor/Drive Assembly Cover

The Motor/Drive Assembly Cover should be placed over the top

of the Tilt N Store



Top Frame piece and motor.

Secure the Assembly cover by installing 3 black ¼” Torx screws.

➢Attaching Hanging Arms to the frame

Tap in 2 brass bearings on either side of each hanging arm.

Next, place the hanging arm into the arm bracket and slide the

shoulder bolt through to secure the hanging arm to the frame.

Once the shoulder bolt is through, place a washer over the

threaded end and install the cap nut.

Page 7

Tilt N Store Installation Manual

➢Connecting Straps to the Super Bracket

Loop the straps around the pull bar as you slide the pull bar into

the super bracket.

➢Mounting the Super Bracket to the Hanging Arms

Attach the hanging arms to the Super Bracket near the top of

the hanging arms by lining up the screw holes and securing the

super bracket by installing 6 black ¼” Torx screws on the back

and 4 black ¼” Torx screws on the front of the super bracket.

➢Mounting the Nameplate

With the super bracket installed on the hanging arms, you can

install the nameplate. The nameplate attaches to the top of the

hanging arms and super bracket and is held on by 4 black ¼”

Torx screws.

Page 8

Tilt N Store Installation Manual

➢Mounting the Super Bracket Cover

The Super Bracket Cover is installed on the load side of the Tilt

N Store



. It is attached by 8 ¼” Torx screws as shown on the left.

➢Mounting Hang Bar and Load Attachment

When installing the hang bar, place shaft collars on either side

of the attachment and on either side of each hanging arm.

NOTE: Ensure that the attachment is centered

➢Mounting and Adjustment of Eye Sensors and Reflector

Mount the Eye Sensor box to the lower frame on the side with

the wire hole by installing 2 black ¼” Torx screws.

Attach the reflector arm to the hanging arm by installing 2 black

¼” Torx screws.

➢Installing Eye Sensor Cover

Mount the Eye Sensor cover to the Eye Sensor box by placing

the cover over the eye sensor box as shown on the left and

installing 2 Zinc Screws.

Page 9

Tilt N Store Installation Manual

➢Where to Mount the Control Box

The control box should be mounted at a location with the Tilt N

Store



in plain sight and hardwired in by an electrician.

➢Wiring Motor and Eye Sensor to Control Box

Wiring from the motor and eye sensors to the control box must

be completed by a certified electrician.

Troubleshooting

Problem: The machine will not run.

Solution: Call maintenance and have them check:

1. The Control Box is receiving power.

2. The Tilt N Store motor and eye sensor are securely fashioned in the correct location of the control

box.

3. If the problem persists call us directly at



651-777-1554.

Problem: The machine will not go up completely.

Solution: Call maintenance and have them check:

1. Ensure that there is not excess glare coming from any part of the reflector arm to the eye sensors

2. The Tilt N Store may be overloaded. The maximum load for the Tilt N Store is 250-300 pounds

depending on wall. Remove the load and try again.

3. If the problem persists call us directly at



651-777-1554.

Maintenance

Your Tilt N Store



requires no lubrication or other maintenance.

Periodically check the nylon Hang Straps and look for wear, cuts or abrasion.

Page 10

Tilt N Store Installation Manual

Warranty

Five Year Mechanical Warranty

Five Year Limited Mechanical Warranty for the Tilt N Store



Lift and Store, LLC. (“L&S” herein) guarantees its mechanical components to be free from defects in

materials and workmanship under the service for which they are intended. L&S

will repair or replace without charge any parts or products which are found to be defective

within one (1) year from the date of shipment or, at the option of L&S, will refund the

purchase price. This does NOT include labor, or travel expenses related to labor, after one

(1) year from the date of installation.

Exclusions of Other Warranties: The warranty described in the above paragraph shall be

IN LIEU OF any other warranty, expressed or implied, including but not limited to, any

implied warranty of MERCHANTABILITY or fitness for a particular purpose.

Extent of Warranty: This warranty extends only to the original purchaser of our product.

The warranty terminates upon any transfer of ownership, moving or reinstallation of this

Machine.

Acts Invalidating Warranty: This warranty is void if the purchased product has been

subjected to alteration, misuse, abuse, damage by others, Acts of God, or if normal

maintenance has not been provided.

Items Specifically Excluded from this Warranty:

Fuses or circuit breakers.

Damage caused by overloading of equipment by customer.

Damage caused by installation or moving of equipment or accessories by others.

Damage or injuries caused by failure to follow all safety procedures in this manual or

subsequent technical bulletins.

Claim Notification: See the Claim Notification Form on page 15. Purchaser must notify

L&S in writing within five (5) working days of any occurrence to receive relief under the

terms of the warranty. Failure to notify L&S in writing may invalidate warranty.

Limitation of Remedies: By purchasing L&S's products, the purchaser agrees with L&S

that the purchaser's sole and exclusive remedy shall be for the repair or replacement of

defective parts or products, without charge. The purchaser agrees that no other remedy

(including but not limited to incidental or consequential damages for lost profits, lost

sales, injury to person or property, or any other incidental or consequential loss) shall be

available to purchaser.

Page 11

Tilt N Store Installation Manual

One Year Electrical Warranty

One Year Limited Electrical Warranty for the Tilt N Store



Lift and Store, LLC. (“L&S” herein) guarantees its electrical components to be free from

defects in materials and workmanship under the service for which they are intended. L&S