Laney F67-LIONHEART User manual

www.laney.co.uk
2
USER MANUAL
1 - PAIR BUTTON
2 - PAIR LED
3 - VOLUME CONTROL
4 - BASS
5 - TREBLE
6 - AUX IN
7 - USB CHARGING SOCKET
8 - POWER LED
9 - POWER SWITCH
10 - PSU SOCKET
FEATURES
F67-LIONHEART
F67-SUPERGROUP
9
76
5431
2 8
10
9
76
543
1
2 8

www.laney.co.uk 3
USER MANUAL
www.laney.co.uk
POWERING ON
•Turn volume (3) down.
•Throw the power switch (9).
•Press the PAIR (1) button – follow the instructions detailed below.
•Connect to LANEY SOUND SYSTEMS on your device.
•Play Music.
PAIRING
•If the blue pair led is not illuminated then no device is connected to the
LANEY SOUND SYSTEMS F67.
•In order to pair your device, follow the procedure detailed below.
 •Pressandholdthepairbutton(1)untiltheblueLEDstartstoashslowly.
•Pairing mode times out after one minute.
•On your device search for LANEY SOUND SYSTEMS and connect. The led will change to
continuous blue when connected.
•Note, you cannot start a new pairing request whilst a device is already connected,
 youmustrstdisconnecttherstdeviceandthenstartpairing.
•The LANEY SOUND SYSTEMS F67 allows multiple devices to connect to it. If you have
previously connected, it should accept a connection request.
•If you start playing a song, it will take over from the currently connected device.
 Thepairledwillchangetoanintermittentblueashwhenmultipledevicesare
connected.
•Pressing and holding the pair button for 10 seconds forces the LANEY SOUND SYSTEMS F67
to forget all the devices currently connected.
OPERATION

www.laney.co.uk
4
USER MANUAL
PLAYING TRACKS
•When your device is connected. You can quickly tap the PAIR (1) button to play/pause the
 currentlyselectedtrack.Theledwillbrieyblinkred/blue
•When there is a track playing, you can double tap the pair button to skip to the next track.
AUX IN (6)
•Use the provided 1/8” aux cable to connect your device to your AUX IN input.
CHARGING YOUR DEVICE (7)
•You can use your LANEY SOUND SYSTEMS F67 player straight out of the box, but it is
 recommendedthatyougiveitafull8hourschargebeforeyouuseitthersttimeinorderto
get optimum battery life.
•You can also use the LANEY SOUND SYSTEMS F67 as a powerbank to charge your device
using the USB port.
CHARGING YOUR BLUETOOTH SPEAKER
•The power led defaults to blue when powered on and using the internal battery. The led will
 startashingasthebatteryrunslowtoindicateitshouldbechargedsoon.Theledashes
progressively slower as the battery is nearing exhaustion and should be charged.
•Tochargewhilenotusingthespeaker.Makesurethepowerswitchissettoo,then
insert the included 12V power supply into the charging socket (10) on the rear of
the unit. The led changes to a constant red colour while charging. When charging is
 complete(aroundfourhours)theledwillgoo.
•To charge while using the speaker. Make sure the power switch is set to on, then
insert the included 12V power supply into the charging socket (10) on the rear of the
unit. The led changes to a constant purple colour while charging. When charging is
 complete(aroundfour-vehours,dependingonspeakervolume)theledwillchange
 toBlue.Note,ifthepowerledisashingwhilepluggedin,itisnotinchargemode.
Make sure the unit was turned on prior to plugging the PSU in.

www.laney.co.uk 5
USER MANUAL
www.laney.co.uk
Manufacturer: Laney Electronics Ltd.
© 2020 Laney Electronics Ltd. May not be reproduced without prior written consent
In the interest of continued product develoment, Laney reserve the right to amend product specication without prior notice
F67-LIONHEART F67-SUPERGROUP
F67-LIONHEART/F67-SUPERGROUP
50Hz-20KHz
105 dB
160W Peak, 80W Continuous, 2 x 20W RMS
Stereo 3.5mm Aux In
BassReex,rearported
Bluetooth 4.1 A2DP
Bass,Treble,Volume.PairButton,On/Otoggleswitch.
2x 3/4” Dome Tweeter
4” dual coil woofer
Wooden
F67-LIONHEART-DurableBluevinylnishwithLionheart
Cream/Blue Front Fret
F67-SUPERGROUP - Durable Black vinyl with Supergroup
vintage front fret
Integrated carry strap handle
Comes with 12V/3A SMPS. Charges internal battery.
PSU is ~100-240V universal with separate mains lead
16 x 26.5 x 15.5 cm /6.3” x 10.4”x 6.1”
2.8Kg, 6.2 lbs
28 x 31.5 x 21.5 cm/11” x 12.4” x 8.5”. 0.019 M3
3.5Kg, 7.7 lbs
Model
Frequency response (-3)
Max SPL (1M) (Peak)
Power Rating
Input Connector
Cabinet Type
Other
Controls
HF Driver
LF Driver
Enclosure
Finish
Handle
Power supply
Unit dimensions (HWD)
Unit weight
Carton dimensions (HWD)
Packed weight
SPECIFICATIONS

www.laney.co.uk
2
USER MANUAL
1 - PAIR BUTTON
2 - PAIR LED
3 - VOLUME CONTROL
4 - BASS
5 - TREBLE
6 - AUX IN
7 - USB CHARGING SOCKET
8 - POWER LED
9 - POWER SWITCH
10 - PSU SOCKET
FEATURES
F67-LIONHEART
F67-SUPERGROUP
9
76
5431
2 8
10
9
76
5431
2 8

www.laney.co.uk 3www.laney.co.uk
USER MANUAL
MISE EN MARCHE
• Coupez le volume (3).
• Mettez en route avec l’interrupteur général (9).
• Appuyez sur le bouton PAIR (1) – suivez les instructions détaillées ci-dessous.
•Sur l’appareil à coupler, sélectionnez LANEY SOUND SYSTEMS.
•Mettez la musique en route.
COUPLAGE
• Si le voyant bleu de couplage n’est pas allumé, aucun appareil n’est lié au lecteur BlueTooth du
LANEY SOUND SYSTEMS F67 .
•Pour coupler votre appareil, veuillez suivre la procédure détaillée ci-dessous.
•Appuyez sur le bouton PAIR (1) pendant une seconde pour activer le mode couplage.
• Le voyant bleu clignote lentement. La tentative de couplage dure une minute.
• Sur votre appareil, sélectionnez LANEY SOUND SYSTEMS. Le voyant bleu s’allume en continu lorsque
le couplage est terminé.
• Note: vous ne pouvez pas commencer un nouveau couplage alors qu’un appareil est déjà connecté, il
faut d’abord déconnecter le premier appareil avant de commencer le nouveau couplage.
• Le LANEY SOUND SYSTEMS F67 permet de connecter plusieurs appareils. Si un couplage a été
 eectuéprécédemment,ildevraitaccepterautomatiquementuneconnectionultérieure.
• Si vous démarrez la lecture d’un morceau sur un appareil, celui-ci devient prioritaire.
Le voyant bleu va clignoter de façon intermittente lorsque plusieurs appareils sont connectés.
• En appuyant et en maintenant la pression sur le bouton de couplage pendant 10 secondes,
le LANEY SOUND SYSTEMS oublie la liaison de tous les appareils précédemment connectés.
FONCTIONNEMENT