Laney Linebacker LR5 User manual

Duration Per
Day in Hours
8
6
4
3
2
1 ½
1
½
¼ or less
Sound Level dBA,
slow response
90
92
95
97
100
102
105
110
115
1).Read & Retain these Instructions carefully before installing or operating this product.
2).Comply withWarnings: All warnings and instructions for these products should be adhered to.
3).Unpacking:On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the Laney factory to
your dealer.In the unlikely event that there has been damage,please repack your unit in its original carton and consult your dealer. We strongly advise you to
keep your original transit carton,since in the unlikely event that your unit should develop a fault, you will be able to return it to you dealer for rectification
securelypacked.
4). AmplifierConnection: Inorderto avoid damage,itisadvisableto establishand followapattern forturningonand offyoursystem.Withallsystemparts
connected,turn on source equipment,CD/MP3 players,mixers/recorders,etc,BEFORE turning on your guitar amplifier.Many products have large transient
surgesatturnonandoffwhichcancausedamagetoyourspeakers.ByturningonyourguitaramplifierLASTandmakingsureitslevelcontrolissettoaminimum,
any transients from other equipment should not reach your loud speakers.Wait till all system parts have stabilised,usually a couple of seconds.Similarly when
turningoffyoursystemalwaysturndownthelevelcontrolsonyourguitaramplifierandthenturnoffitspowerbeforeturningoffotherequipment
5).Servicing:Refer all servicing to qualified service personnel.Servicing is required when the apparatus has been damaged in any way,such as when the DC
PowerSupplyis damaged,liquidhas beenspilledorobjectshavefallen intothe apparatus,theapparatushas beenexposedtorainormoisture,doesnot operate
normally,orhasbeendropped.
6).Placement:This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids,
such as vases,upon the apparatus.
Do not install near any heat sources such as radiators,heat registers,stoves or other apparatus (including amplifiers) that produce heat. Do not block any
of the ventilation openings.
Use only with a cart,stand,tripod,bracket,or table specified by the manufacturer,or sold with the apparatus.When a cart is used,use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
7).When using the DC power Supply:Only use the approved DC power supply provided by the manufacturer.Rating 12Vdc 500mA. Protected
by a 125°C thermal fuse.
Make sure that the line voltage at the installation matches the input voltage on the DC power Supply.
Protect the power cord on the DC power Supply from being walked on or pinched,particularly at plugs,convenience receptacles,and the point they exit
from the apparatus.(See notes on using the DC Power Supply page 10).
8).Batteries:Use only alkaline batteries (LR6) in the product.(See notes on fitting and replacing batteries page 10-11).
9).Sound Levels: Exposure to extremely high noise levels may cause a permanent hearing loss.Individuals vary
considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to
sufficiently intense noise for a sufficient time.
The U.S.Government’s Occupational Safety and HealthAdministration (OSHA) has specified the following
permissible noise level exposures:According to OSHA,any exposure in excess of the above permissible limits could
result in some hearing loss.Earplugs or protectors to the ear canals or over the ears must be worn when operating
this amplification system in order to prevent a permanent hearing loss,if exposure is in excess of the limits as set
forth above.To ensure against potentially dangerous exposure to high sound pressure levels,it is recommended that
all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system
be protected by hearing protectors while this unit is in operation.
10).Maintenance:Clean only with a dry cloth.
Care of your Laney amplifier will prolong it's life.....and yours!

Durée par
Jour (heures)
inférieur
8
6
4
3
2
1 ½
1
½
¼ ou
Niveau sonore
moyen (dBA)
90
92
95
97
100
102
105
110
115
1).Lisez le & Maintenez ces instructions: soigneusement avant d'installer ou actionner ce produit.
2).Conformez-vous aux avertissements:Tous les avertissements et instructions pour ces produits devraient.
3).Déballage: Au déballage de votre produit vérifiez svp soigneusement tous les signes des dommages qui ont pu s'être produits tandis qu'en transit de l'usine de
Laney à votre revendeur.Dans l'événement peu probable qu'il y a eu des dommages,réemballent svp votre unité dans son carton original et consultent votre revendeur.
Nous vous conseillons fortement que pour garder votre carton original de passage,puisque dans l'événement peu probable que votre unité devrait développer un
défaut,vous pourrez le renvoyer te revendeur pour la rectification solidement emballée.
4).Raccordement d'amplificateur:Afin d'éviter des dommages,il est recommandé d'établir et suivre un modèle pour tourner en marche et en arrêt votre système.
Avec tout le système les pièces ont relié,allument l'équipement de source,CD/MP3 les joueurs,mélangeurs/enregistreurs,etc.,AVANT DE mettre en marche votre
amplificateur de guitare.Beaucoup de produits font tourner de grandes montées subites passagères à en marche et en arrêt qui peuvent endommager vos haut-parleurs.
En mettant en marche votre BOUT d'amplificateur de guitare et en veillant sa commande de niveau est placé à un minimum,toutes les coupures de l'autre équipement
ne devrait pas atteindre vos haut-parleurs forts.Attendez jusqu'à ce que toutes les pièces de système ont stabilisé,habituellement deux ou trois secondes.De même en
arrêtant votre système déclinez toujours les commandes de niveau sur votre amplificateur de guitare et coupez alors son courant avant d'arrêter l'autre équipement
5).Entretien: Référez-vous tous qui entretiennent au personnel de service qualifié.L'entretien est exigé quand l'appareil a été endommagé de quelque façon,comme
quand l'approvisionnement d'alimentation CC Est endommagé,liquide a été renversé ou les objets sont tombés dans l'appareil,l'appareil a été exposé à la pluie ou à
l'humidité,ne fonctionne pas normalement,ou a été lâché.
6).Placement: Cet appareil électrique ne devrait pas être exposé à l'égoutture ou l'éclaboussement et le soin devraient être pris pour ne pas placer des objets
contenant des liquides,tels que des vases,sur l'appareil.N'installez près d'aucune source de chaleur telle que des radiateurs,des registres de la chaleur,des fourneaux ou
d'autres appareils (amplificateurs y compris) cette chaleur de produit.Ne bloquez pas les ouvertures l'unes des de ventilation.Employez seulement avec un chariot,un
stand,un trépied,une parenthèse,ou une table spécifique par le fabricant,ou vendue avec l'appareil.Quand un chariot est utilisé,faites attention en déplaçant la
combinaison de chariot/appareil pour éviter des dommages de incliner-au-dessus de.
7).En employant l'approvisionnement d'alimentation CC: Employez seulement l'approvisionnement d'alimentation CC Fourni par le fabricant.Classement
12Vcc 500mA.Protégé par un 125 ° C fusible thermique. Assurez-vous que tension secteur à l'installation assortit la tension d'entrée sur l'approvisionnement
d'alimentation CC.Protégez le cordon de secteur sur l'approvisionnement d'alimentation CC Contre être marchée dessus ou pincement,en particulier derrière les
fiches,derrière les douilles de convenance,et derrière le point qu'ils sortent de l'appareil.(Voir les notes sur employer la page d'approvisionnement d'alimentation CC
10).
8).Batteries: Utilisez seulement les accumulateurs alcalins (LR6) dans le produit.(Voir les notes sur l'ajustage de précision et remplacer la page de batteries 10-11).
Niveaux
9).Sound: L'exposition aux niveaux extrêmement élevés de bruit peut causer une perte d'audition permanente.Les individus
varient considérablement dans la susceptibilité à la perte d'audition due au bruit,mais presque chacun perdra une certaine
audition si exposé au bruit suffisamment intense pendant un temps suffisant.L'administration du gouvernement des États-
Unis (OSHA) a spécifié les expositions permises suivantes de niveau de bruit :Selon l'OSHA,n'importe quelle exposition au-
dessus des limites permises ci-dessus a pu avoir comme conséquence une certaine perte d'audition.Des boules quies ou les
protecteurs aux canaux d'oreille ou au-dessus des oreilles doivent être portés en actionnant ce système d'amplification afin
d'empêcher une perte d'audition permanente,si l'exposition est au-dessus des limites comme déterminé ci-dessus.Pour
s'assurer contre l'exposition potentiellement dangereuse aux niveaux élevés de pression acoustique,on lui recommande que
toutes les personnes aient exposé à l'équipement capable de produire les niveaux élevés de pression acoustique tels que ce
système d'amplification soient protégées par les protecteurs auriculaires tandis que cette unité est en fonction.
10).Entretien: Nettoyez seulement avec un tissu sec.
Le soin de votre amplificateur de Laney prolongera it' ;la vie de s .....et vôtre !

Dauer pro
Tag in Stunden
8
6
4
3
2
1 ½
1
½
¼ oder weniger
Geräuschpegel dBA
langsame Reaktion
l
90
92
95
97
100
102
105
110
115
4
LR5
1). Lesen Sie & Vor der Installierung oder dem Betrieb dieses Produktes behalten Sie diese Anweisungen sorgfältig.
2). Willigen Sie mit Warnungen ein: Alle Warnungen und Anweisungen für diese Produkte sollten an gehaftet werden.
3). Auspacken: Auf Auspacken Ihres Produktes überprüfen Sie bitte sorgfältig auf allen möglichen Zeichen des Schadens, die während bei dem Transport von
der Laney Fabrik zu Ihrem Händler aufgetreten sein können. Im unwahrscheinlichen Ereignis, dass packen es Schaden gegeben hat, bitte Ihre Maßeinheit in
seinem ursprünglichen Karton ein und konsultieren Ihren Händler. Wir beraten Sie stark, dass Ihren ursprünglichen Durchfahrtkarton halten, da im
unwahrscheinlichen Ereignis, dass Ihre Maßeinheit eine Störung entwickeln sollte, Sie in der Lage sind, sie zu Ihnen zurückzubringen Händler für die sicher
verpackte Korrektur.
4). Verstärker-Anschluss: Um Schaden zu vermeiden, ist es ratsam ein Muster für einschalten und weg von Ihrem System herzustellen und zu folgen. Mit
allem System schlossen die Teile an, schalten Quellausrüstung, CD/MP3 Spieler, Mischer/Recorder, usw. ein, BEVOR sie Ihren Gitarrenverstärker
einschielten. Viele Produkte lassen große vorübergehende Schwankungen an an und abstellen, die Schaden Ihrer Lautsprecher verursachen können. Indem
man Ihr Gitarrenverstärker LETZTES einschält und seine waagerecht ausgerichtete Steuerung sicherstellt, wird auf ein Minimum, alle mögliche
Ausgleichströme von anderer Ausrüstung sollte Ihre lauten Lautsprecher nicht erreichen eingestellt. Warten Sie bis alle Systemsteile haben stabilisiert,
normalerweise ein paar Sekunden. Ähnlich wenn Sie Ihr System abstellen, drehen Sie immer unten die waagerecht ausgerichteten Kontrollen auf Ihrem
Gitarrenverstärker und stellen Sie dann seinen Strom ab, bevor Sie andere Ausrüstung abstellen
5). Instandhaltung: Verweisen Sie alle, die auf qualifiziertes Service-Personal instandhalten. Die Instandhaltung wird, wenn der Apparat in jeder Hinsicht
beschädigt worden ist, wie, wenn die Gleichstrom-Versorgung geschädigt wird, Flüssigkeit ist verschüttet worden angefordert, oder Gegenstände sind in den
Apparat gefallen, ist der Apparat Regen oder Feuchtigkeit ausgesetzt worden, funktioniert nicht normalerweise oder ist gefallen worden.
6). Placement: Dieser elektrische Apparat sollte nicht Bratenfett ausgesetzt werden, oder das Spritzen und die Sorgfalt sollten angewendet werden, um die
Gegenstände nicht zu setzen, die Flüssigkeiten, wie Vasen, nach dem Apparat enthalten. Bringen Sie nicht nahe irgendwelchen Wärmequellen wie
Heizkörpern, Hitzeregistern, Öfen oder anderen Apparaten (einschließlich Verstärker) diese Erzeugnishitze an. Blockieren Sie nicht irgendwelche der
Ventilationsöffnungen. Verwenden Sie nur mit einer Karre, einem Standplatz, einem Stativ, einem Haltewinkel oder einer Tabelle, die vom Hersteller spezifiziert
wird oder mit dem Apparat verkauft ist. Wenn eine Karre benutzt wird, Vorsicht, wenn Sie die Karren-/Apparatekombination verschieben, um Verletzung von
spitzen-über zu vermeiden.
7). Wenn die Gleichstrom-Versorgung verwendet wird: Benutzen Sie nur die Gleichstrom-Versorgung, die vom Hersteller bereitgestellt wird. Bewertung
12Vdc 500mA. Geschützt durch ein 125 ° C Thermosicherung. Überprüfen Sie, ob die Linie Spannung an der Installation die Eingangsspannung auf der
Gleichstrom-Versorgung zusammenbringt. Schützen Sie das Netzanschlusskabel auf der Gleichstrom-Versorgung vor an gegangen werden oder, besonders
an den Steckern, an den Hilfsaufnahmewannen und am Punkt geklemmt werden, die sie vom Apparat herausnehmen. (Sehen Sie Anmerkungen über die
Anwendung der Versorgungseite10).
8). Batterien: Benutzen Sie nur alkalische Batterien (LR6) im Produkt. (Sehen Sie Anmerkungen über Befestigung und das Ersetzen der Batterieseite10-11).
Niveaus
9). Sound: Aussetzung zu den extrem hohen Geräuschpegeln kann einen dauerhaften Verlust der Hörfähigkeit
verursachen. Einzelpersonen schwanken beträchtlich in Anfälligkeit zum noise-induced Verlust der Hörfähigkeit, aber
fast jeder verliert irgendeine Hörfähigkeit, wenn es genug intensiven Geräuschen während einer genügenden Zeit
herausgestellt wird. Die der US-berufliche Sicherheits-und Gesundheits-Verwaltung Regierung (OSHA) hat die
folgenden zulässigen Geräuschpegelbelichtungen spezifiziert: Entsprechend OSHA konnte jede mögliche Belichtung
mehr als notwendig die oben genannten zulässigen Begrenzungen etwas Verlust der Hörfähigkeit ergeben.
Ohrenpfropfen oder Schutze zu den Gehörgängen oder über den Ohren müssen getragen werden, wenn man dieses
Verstärkungssystem laufen lässt, um einen dauerhaften Verlust der Hörfähigkeit zu verhindern, wenn Belichtung mehr
als notwendig die Begrenzungen ist, wie oben festgelegt. Um gegen möglicherweise gefährliche Aussetzung zu den
hohen Schalldruckpegeln sicherzustellen, wird es empfohlen dass alle Personen der Ausrüstung herausstellten, die
zum Produzieren der hohen Schalldruckpegel wie dieses Verstärkungssystem fähig ist werden geschützt durch
Hörschutze während diese Maßeinheit in Kraft ist.
10). Wartung: Säubern Sie nur mit einem trockenen Tuch.

Duración por
Día en Horas
8
6
4
3
2
1 ½
1
½
¼ o menos
Nivel de Sonido
dBA, Respuesta Lenta
90
92
95
97
100
102
105
110
115
1). Lea el & Conserve estas instrucciones cuidadosamente antes de instalar o de funcionar este producto.
2). Confórmese con advertencias: Todas las advertencias e instrucciones para estos productos se deben adherir.
3). Desempaque: Al desempaquetar su producto compruebe por favor cuidadosamente para saber si hay cualquier muestra del daño que pudo haber
ocurrido mientras que en tránsito de la fábrica de Laney a su distribuidor autorizado. En el acontecimiento inverosímil que ha habido daño, reembala por
favor su unidad en su cartón original y consulta a su distribuidor autorizado. Le aconsejamos fuertemente que guardar su cartón original del tránsito, puesto
que en el acontecimiento inverosímil que su unidad debe desarrollar una avería, usted podrá volverlela distribuidor autorizado para la rectificación llena con
seguridad.
4). Conexión del amplificador: Para evitar daño, es recomendable establecer y seguir un patrón para dar vuelta por intervalos a su sistema. Con todo el
sistema las piezas conectaron, giran el equipo de la fuente, CD/MP3 a los jugadores, mezcladores/registradores, etc, ANTES de girar su amplificador de la
guitarra. Muchos productos hacen que las oleadas transitorias grandes en den vuelta por intervalos que pueden causar daño a sus altavoces. Girando su
ÚLTIMO del amplificador de la guitarra y cerciorándose de su control llano se fija a un mínimo, cualquier transeúnte del otro equipo no debe alcanzar sus
altavoces ruidosos. Espere hasta que todas las piezas del sistema se han estabilizado, generalmente uces par de segundos. Semejantemente al apagar su
sistema rechace siempre los controles llanos en su amplificador de la guitarra y después corte su corriente antes de apagar el otro equipo
5). Mantenimiento: Refiera todos que mantienen a los personales de servicio calificados. Se ha derramado el servicio se requiere cuando el aparato se ha
dañado de cualquier manera, por ejemplo cuando se daña la fuente de corriente continua, Líquido o los objetos han caído en el aparato, el aparato se ha
expuesto a la lluvia o a la humedad, no funciona normalmente, ni se ha caído.
6).Placement: Este aparato eléctrico no se debe exponer al goteo o el salpicar y el cuidado se deben tomar para no poner los objetos que contienen
líquidos, tales como floreros, sobre el aparato. No instale cerca de ninguna fuentes de calor tales como radiadores, registros del calor, estufas u otros
aparatos (amplificadores incluyendo) ese calor del producto. No bloquee las aberturas unas de los de la ventilación. Utilice solamente con un carro, un
soporte, un trípode, un soporte, o una tabla especificada por el fabricante, o vendida con el aparato. Cuando se utiliza un carro, tenga cuidado al mover la
combinación del carro/del aparato para evitar lesión de inclinar-sobre.
7). Al usar la fuente de corriente continua: Utilice solamente la fuente de corriente continua Proporcionada por el fabricante. Clasificación 12Vdc
500mA. Protegido por un fusible de 125 ° C térmica. Cerciórese de que la línea voltaje en la instalación empareje el voltaje de entrada en la fuente de
corriente continua. Proteja el cable eléctrico en la fuente de corriente continua Contra ser caminado encendido o sejeción, particularmente en de los
enchufes, de los receptáculos de la conveniencia, y del punto que salen del aparato. (Véase las notas sobre usar la página de la fuente de corriente
continua10).
8). Baterías: Utilice solamente los acumuladores alcalinos (LR6) en el producto. (Véase las notas sobre la guarnición y el reemplazo de la página de las
baterías10-11). Niveles
9).Sound: La exposición a los niveles de ruidos extremadamente altos puede causar una pérdida de oído
permanente. Los individuos varían considerablemente en susceptibilidad a la pérdida de oído inducida por el
ruido, pero casi cada uno perderá una cierta audiencia si está expuesta al ruido suficientemente intenso por un
suficiente tiempo. La Occupational Safety and Health Administration del gobierno de los E.E.U.U. (OSHA) ha
especificado las exposiciones permitidas siguientes del nivel de ruidos: Según el OSHA, cualquier exposición
superior a los límites permitidos antedichos podía dar lugar a una cierta pérdida de oído. Los auriculares o los
protectores a los canales de oído o sobre los oídos deben ser usados al gestionar este sistema de la amplificación
para prevenir una pérdida de oído permanente, si la exposición está superior a los límites según lo dispuesto
arriba. Para asegurar contra la exposición potencialmente peligrosa a los altos niveles de presión sana, se
recomienda que todas las personas expusieron al equipo capaz de producir altos niveles de presión sana tales
como este sistema de la amplificación sean protegidas por los protectores de oído mientras que esta unidad es en
funcionamiento.
10). Mantenimiento: Limpie solamente con un paño seco.
El cuidado de su amplificador de Laney prolongará it' ¡vida de s ..... y la suya!

The Linebacker series is a state of the art,processor-based design,enabling a wide range of different
sounds to be created from your guitar.
The 5W LR5 model,great for bedroom,practice or busking.
Features a 6" custom driver,one instrument channel,one
microphone channel,eleven built in amp models and range of
"must have" effects like;chorus,phase,flange,tremolo,reverb
and delay.Providing everything you need from clean tones to
full-out overdrive. Also provided is a handy built in guitar tuner
so you always have the best possible sound.
On the rear panel can be found the controls & sockets for the
Microphone & Headphones,along with the DC Power In socket
and Power switch.
The cabinet features an open back design enabling easy stowage
of Power Supply,cables,etc. With its included Guitar Style strap,
the amp is easily transported to wherever your sounds are
needed the most.
To enable you to get the most from your new Laney amp please read and retain this manual.
Best wishes from all at Laney

ON ON
P
H
A
S
E
R
S
U
R
O
H
C
E
G
N
A
L
F
T
R
E
M
O
L
O
7
19
3
10
46
0
5
8
2
7
19
3
10
46
0
5
8
2
7
19
3
10
46
0
5
8
2
5A
6E
3G
4D
1E
2B VOLT
HEART+
CRYSTAL
VC+
+
VC
HEART
VOLT+
WRECK
TI+
TI
CRYSTAL
POWER
MOD FX LED
DEL FX LED
PRESENCE Control
CONTOUR Control
AUX IN Jack
AMP/TUNER Selector Control
VOLUME Control
GUITAR INPUT Jack Socket
MOD FX on/off Button
MOD FX Control-Chorus,
Flanger,Phaser,Tremolo
DEL FX Control-Delay,
Reverb
DEL FX on/off Button
TUNER & Button
TUNER LED

MIC VOLUME
POWER
7
19
3
10
46
0
5
8
2
PHONES/
RECORD OUT
Power To The Music
WWW.LANEY.CO.UK
ON
OFF
DESIGNED AND ENGINEERED IN THE UK
MADE IN CHINA. FABRIQUE EN CHINE.
SERIAL NO:
N15039
12V DC IN
MODEL: LR5
L Z B1 2 3 4
MIC Socket
MICVOLUME
PHONES/RECORD OUT Socket
SECURITY SLOT
MODEL & SERIAL No
POWER Switch
POWER ON LED
12V DC Inlet Socket
BATTERY COMPARTMENT

DC Power Supply:Your LR5 comes supplied with a 12V DC Power Supply,this is easily
fitted between the mains outlet and the amp.When using the amp with the power supply a
few precautions should be followed:
1). Only use the DC Power supply that is supplied by the manufacturer.The use of other
DC Power Supplies may cause damage or other problems.
2). Turn the power switch to OFF and disconnect any other attached devices,before
plugging in and turning ON the DC Power Supply.
3). When the DC Plug is connected to the socket,the battery compartment is isolated
from the unit.Both the DC Power Supply and the battery tray are independent of each
other.
4). Although no harm will come to the batteries if left in place whilst the DC Power supply is being used,it is recommended
that they be removed. Use either one power source or the other.
Batteries:The use of a DC Power Supply is recommended as the units main power source,however,should you prefer to use
batteries,use only Alkaline type (LR6).
Used continuously the batteries will last for approximately 13 hours.(This will vary greatly with the actual conditions of use).
As the batteries run down,the power indicator on the fascia panel will become dim when the battery power is too low.
Replace the batteries or revert to the DC Power Supply.
Fitting Batteries:When installing or replacing batteries,always turn the power switch to the OFF position and disconnect
any other devices you have may have connected.This prevents damage to your speaker and/or other devices.Follow the photo
sequence to fit a set of batteries.
1).Turn the amplifier upside down to access the battery tray that is located under the chassis,place the amp on a piece of felt
or cloth to avoid damage.
2). Push the catch to release,then lift out the lid of the battery tray and insert 6AA batteries,ensure that the orientation is
correct to the legend on the tray.
3).When closing the lid of the battery tray,insert the tabs opposite the catch first,then push the lid down until a click is heard.

If used incorrectly batteries may leak or explode and cause damage or injury,please take the following precautions.
1). Carefully follow the installation instructions for fitting new batteries,especially the polarity.
2). Avoid mixing new batteries with old or part used batteries.
3). Avoid mixing battery types.
4). Do not try to recharge or take apart alkaline batteries.
5). Remove the batteries from the unit if it is not going to be used for a long time.
6). If batteries have leaked in the battery tray,remove the batteries and all traces of the discharge from the tray.Use caution so
that none of the discharge gets near the skin or the eyes.Any affected areas should be immediately rinsed with cold running
water,seek medical advice,
7). Do not dispose of used batteries in fire or water systems.Batteries must not be exposed to excessive heat such as sunlight,
fire or the like.
8). Used batteries should always be disposed of in compliance with the current regulations applicable to the country/region
where you live.
Attaching the Strap:Attach the supplied strap to the
buttons on each side of the cabinet securely,so that it does
not become detached causing damage or injury.
+
-

POWER: This is the power ON/OFF switch.
INPUT JACK: Connect your guitar here.Use only good quality cables to
avoid poor sound quality.
TUNER/AMP MODEL SELECTION: Choose from the various pre
programmed amp models
VOLUME CONTROL: Adjust the volume level of the instrument
connected to the Input Jack.
EQUALISATION CONTOUR/PRESENCE: This set of tone
controls can have a great effect on your sound.
MOD FX: Choose from Chorus,Flanger,Phaser orTremolo.
DEL FX: Choose from Delay or Reverb.
Now the power supply is connected or the batteries are fitted read on.

MIC SOCKET &VOLUME CONTROL:Connect your microphone and adjust its volume.Use
only dynamic microphones,electret & condenser mic’s will not work.
HEADPHONE/RECORD OUT: A rear panel 6.35” stereo jack is provided for headphone use.

IN DEPTH
12V DC POWER SOCKET: Connect to your DC Power Supply. Make sure the voltage marked
on the DC Power Supply matches the outlet voltage for your country!
POWER: This is the main power ON/OFF switch.After switch on,all of the LED’s on the fascia light
up momentarily,after a couple of seconds the LED’s indicate the previous
settings used: i.e.If the amp was last used with Chorus & Reverb,the MOD
FX & DEL FX LED’s will be lit. The Power LED will also be lit with the
switch in the ON position..
INPUT JACK:Connect your guitar here.Use only good quality cables to
avoid poor sound quality.
AUX IN JACK: Use this input for CD/MP3 players to allow you to play
along to the music or use as backing.For use with standard stereo 3.5mm
jack leads.The overall volume of your player is controlled by the its own volume control.
(NOTE:This input is not muted when in the guitar tuner is in use).
AMP: This control allows the user to select from the various factory pre
programmed amp models.These are not just guitar amp settings,used as a
starting point,each can be configured as a compilation of amp and/or
EQ/effect set-ups to give some of music’s most inspirational sounds.There
is a vast choice to suit your own style & taste.
(Descriptive table to follow Page 18)
TIP
TIP

VOLUME CONTROL: Controls the volume of the instrument connected to the Input Jack.This
control does not have any effect on any microphone connected to
the amp.
EQUALISATION CONTOUR/PRESENCE: As the name
suggests this set of controls can have a great effect on your sound.
Basically the Contour control is a mix of conventional Bass & Mid
controls,and the Presence acts more as a Bright/Tone Control.
MOD FX: Activate by pressing the ON Button.This control applies
various effects to make your own unique sound.Choose from
Chorus,Flanger,Phaser orTremolo depending on the style required
or theAmp Model chosen,the LED will flash according to the
modulation of effect used.
DEL FX: Activate by pressing the ON button.The first section of
the rotary control adjusts the length of Delay applied to the signal,
the LED will flash according to the delay time.The second half of the
control adjusts the length of Reverb applied to the signal from Room
to Cathedral.
The really important thing is to experiment with the EQ and FX controls,because they effect each amp
model in a different way.
The cool sounds you discover can be noted in the user settings section.(Page 21/22)
TIP

MICVOLUME:Controls the volume of the Mic connected to
the Mic Input Socket.This control is independent from the
instrument volume control on the fascia.
MIC SOCKET: Connect a microphone here.Please note the
following when a mic is connected to the amp:
The location of the microphone relative to the amp could cause
feedback as could the volume level being too high.Both are
easily remedied.
Use a Dynamic Mic only,you can not use a condenser mic or a plug-in powered mic that requires a power
supply.
HEADPHONE/RECORD OUT: A rear panel 6.35” stereo jack is provided
for headphone use.This output may also be used to connect to a mixing desk
for recording if required.
(The internal speaker is automatically disconnected when using phones.
If your Phones have a 3.5mm jack an adaptor will be required)
SECURITY SLOT: You can connect commercially available anti-theft cables and other security
devices to the amp.
See http://www.kensington.com/
SERIAL NO: Displays the model and serial number of the unit.
TIP
TIP
TIP

TUNER OPERATION: By pressing theTuner Button the amplifier will Mute and the tuner
function will be activated.
The round LED will flash to indicateTuner operation.
TheAMP selector should then be used to select each string in
turn to be tuned.
These are E,B,G,D,A,E and numbered 1-6 with 1 being the High
“E” and 6 being Low“E”
Adjust the string tension to make just the centre LED light.
(As the tune is approached,the centre LED and the LED from the
direction of tune will speed up flashing to show you are getting
close to the in tune position.
When in tune the LEDs will stop flashing and only the Centre
LED will be continuously lit.
Repeat this for each string and then go back through them again
to make final adjustments if required.
To exit the tuner function press the tuner button.
Alternatively remove the input jack and replace.
(You will be returned to the channel and sound settings prior to tuning.)

Factory Reset:
You can at any time return the amplifier to all its original factory settings.
With the amplifier in the OFF state,hold down the DEL FX Button,turn ON the power switch,continue holding
down the DEL FX Button for a few seconds while all the LED’s flash,then as the LED’s become steady,release the
DEL FX Button & the factory settings are restored.
Amp Model Definitions
Linebacker
Sounds Tone Description Amp modelled
Crystal Pure & Clean Clean channel of an LC amp - bright and full
Crystal + Clean with Compression Clean channel of an LC amp - bright and full + a clean boost pedal to
give more low end
VC Clean & Warm A VC combo set clean
VC+ 1 x 12" Combo Semi Distorted A VC combo with the drive channel switched to give a semi broken up
tone
Heart 1 x 12" Classic vintage tone Lionheart Combo on the clean channel pushed hard giving you a classic
semi distorted vintage tone
Heart + 1 x 12" Classic vintage distorted tone Lionheart combo with more gain dialled in
Volt Classic rock distortion Tube head and cab combination - set to give you a crunch tone
Volt + Classic rock solo tone Tube head driven hard - more gain dialled in
TI Crushing rhythm tone TI signature head pushed
TI + Hard rock solo tone TI signature head pushed hard
Wreck Insane full on gain Drive channel of a modern valve head - full on!

In the interest of continued development, Laney reserves the right to amend product specification without prior notification.
Power Supply 12V DC Power Supply or 6“AA” size Batteries
Output Power Rating 5W
Loudspeaker Custom Designed 6” 8 Ohm Driver
Features 1 Instrument Channel,1 Microphone Channel - (Balanced or Unbalanced)
11 built in amp models
Contour & Presence EQ controls
Chorus,Flanger,Phaser,Tremolo,Delay & Reverb FX
Tuner Function
Security Slot
Size (H*W*D) 301*285*176 UnitWeight 4.5Kg
Included Items DC Power Supply,Guitar Style Carry Strap
This product conforms to the requirements of the following European Regulations, Directives & Rules:-
CE Mark (93/68/EEC), Low Voltage (72/23/EEC), EMC (2004/108/EEC),
RoHS (EU2002/95/EC), WEEE (EU2002/96/EC)
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal Household
waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the
WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage
to try to correct the interference by one or more of the following measures:
?Reorient or relocate the receiving antena
?Increase the separation between the equipment and receiver
?Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
?Consult the dealer or an experienced radio/TV technician for help
Unauthorized changes or modification to this system can void the user’s authority to operate this equipment

7
19
3
10
46
0
5
8
2
Power To The Music
WWW.LANEY.CO.UK
SERIAL NO:
N15039
L ZB 1 2 3 4
Headphones
OR
Mixer Desk
MP3
Dynamic Mic
Guitar