LanReady WCB1105H10DX User manual
LanRea
d
yTec
h
no
l
ogiesInc.
3F.,No.166,Sinhu2ndRd.,NeihuDistrict,TaipeiCity114,Taiwan
Tel:886‐2‐2796‐8188Fax:886‐2‐2796‐8158http//:www.lanready.com
Network on Demand Network on Demand Network on Demand Network on Demand Network on Demand
Model Name: WCB1105H10DX
Product Name: AP Router
Brand Name: LanReady
- WCB11xx_H10PX series and WCB1110H10DX is a 2.4GHz Single Band AP.
- The WCB1110H10DX support the IP65 water/dust-proof standard. It is recommended that you place the AP
under a roof, shelter, or weather-proof container in severe weather environment.
Minimum System Requirements
-- Computer with Windows, MAC OS, or Linuxbased operating system, and an
Ethernet adapter installed
-- Internet Explorer 7.0, Mozilla Firefox® version 12.0, Safari 4.0, or Chrome 20.0 or
newer
Package Contents
-- WCB11xx_H10PX series and WCB1110H10DX Wireless-bgn, 2.4GHz, 800mW
Outdoor AP Bridge
-- PoE Injector
-- Power Adapter (48 V/0.5 A)
-- Pole Mount (Non-detachable)
-- Wall Mount (optional)
-- Two Plastic Mounting Ties
If any of the above items are missing, please contact your reseller.
Physical Installation
STEP 1: Connect an Ethernet Cable to the LAN (PoE) Port on the AP.
Ethernet cable is not included in the package
STEP 2: Mount the AP to a Pole or Wall
2A: Pole Mounting
LanRea
d
yTec
h
no
l
ogiesInc.
3F.,No.166,Sinhu2ndRd.,NeihuDistrict,TaipeiCity114,Taiwan
Tel:886‐2‐2796‐8188Fax:886‐2‐2796‐8158http//:www.lanready.com
Network on Demand Network on Demand Network on Demand Network on Demand Network on Demand
Wrap the included two plastic mounting ties to the pole.
2B: Wall Mounting
It is an optional accessory and fix it on the wall with screws and then attach the device
and use the plastic mounting ties to hold in place.
STEP 3: Connect Grounding Wire
A grounding wire is recommended to protect your device from lightning strikes and the
buildup of static electricity.
- A grounding Wire is not included in the package. It is suggested that you use 16 to 18 AWG grounding wire.
STEP 4: Connect the AP to Your Network
A. Connect the Ethernet cable (connected to the AP in STEP 1) from the AP to the
“P+DATA OUT＂port on the PoE Injector.
B. Connect an Ethernet cable from a router/ switch or PC to the “DATA IN＂port on
the PoE Injector.
C. Attach the power adapter to the connector labeled “POWER IN＂on the PoE
Injector, and attach it into an electrical outlet.
Configuration
If you are configuring the AP locally, connect a PC to the PoE Injector “DATA IN＂
port using an Ethernet cable.
A. Assign a static IP address to your PC which is in the same network segment with
the device. As the default IP address of this unit is 192.168.2.254.
B. Open a web browser and go to http:// 192.168.2.254. Enter “root” as your
username and enter “default” as the password to log into the web UI. Now you can
configure the AP via web UI.
LanRea
d
yTec
h
no
l
ogiesInc.
3F.,No.166,Sinhu2ndRd.,NeihuDistrict,TaipeiCity114,Taiwan
Tel:886‐2‐2796‐8188Fax:886‐2‐2796‐8158http//:www.lanready.com
Network on Demand Network on Demand Network on Demand Network on Demand Network on Demand
Waring
This equipment has been tested and found to comply with the limits for a Class B digi
tal device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This e
quipment generates, uses and can radiate radio frequency energy and, if not installe
d and used in accordance with the instructions, may cause harmful interference to ra
dio communications. However, there is no guarantee that interference will not occur i
n a particular installation. If this equipment does cause harmful interference to radio o
r television reception, which can be determined by turning the equipment off and on, t
he user is encouraged to try to correct the interference by one or more of the followin
g measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the recei
ver is connected. Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co
located or operating in conjunction with any other antenna or transmitter. 2.
This equipment complies with FCC RF radiation exposure limits set forth for an unco
ntrolled environment. This equipment should be installed and operated with a minimu
m distance of 20 centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Table of contents
