Lantech IPOA-1000H User manual

Lantech
IPOA-1000H
User Manual
Ver.1.01
Apr-2015

Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

FCC MARKING
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection
requirement of Council Directive 2004/108/EC on the approximation of the
laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent
from the company.
Trademarks:
All trade names and trademarks are the properties of
their respective companies.

NOTE:
Always make sure the total length of the TX cable DOES NOT exceed 100meter.
Total length is defined as length A + length B
Maximum total cable length is 100meter.
During 100Mbps transmission, the maximum total cable length is 100 meter.
During 1000Mbps speed transmission, recommend maximum cable length less than
90 meter is more desired.
POE signal attenuates every meter, the built-in transformer allows the attenuation to
reach 100 meter long to follow IEEE802.3af / at standard. the higher quality of PD
you connected to, the more reliable the network will be. When connect to a poor
quality PD, it can not generate strong signal to send to remote switch. Always make
sure you have a high quality PD to perform a desired network.

Installation package
This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and
wall-mounted bracket are included.
Wall mount bracket x 2
DIN Rail Kit x 1
Terminal Block x 1
Power connection
This unit is equipped with Voltage booster feature which allow low input voltage
12/24VDC to be boost up to 55VDC for 30w POE power. The provided 4 pin terminal
block can be connected with 12VDC to 56VDC power source. Always Make sure your
input voltage is within this supported voltage range.
Input Voltage: 48VDC (802.3af); 54VDC (802.3at)
Input Voltage: 12V ~56V DC (12V model)
Input Voltage: 24V ~56VDC (24V model)
To make power connection –Follow the printed polarity for V+, V-, Ground. Connect
positive wire to V+ , connect negative wire to V-, also connect neutral wire to ground.
This unit can be connected to two power input.
+V1- is for power input one connection,
+V2-(SW) is for power input two connection
Connecting procedure
STEP 1 –
Take out 4 pin terminal block located in the included mounting kit package.

STEP 2 –
Connect power wire to +V1- or Connect +V2- (SW) as shown above
STEP 3 –
Plug into terminal block socket shown above. Polarity needs to match the V+ and V-
WARNING -- Always SHUTS OFF power source to connect power wire.
WARNING –any exceeded input voltage will not make this unit function and may
damage this unit.
LED indicator

Dip Switch setting
This unit is equipped with 4 pin dip switches which allow users to set the desired POE
power setting to meet your desired POE network. Refer to the setting shown below:
2 Pair**
2 pair 30W is selected
4 Pair**
4 pair 60W is selected (DEFAUT)
Mode A
Mode A End-Span is selected (DEFAULT)
Mode B
Mode B Mid-Span is selected
HiPower
High power 36W is selected (DEFAULT)
PoE at
IEEE802.3at 30W is selected
Reserved (Right)
Reserved (DEFAULT)
Reserved (Left)
Reserved
** Select 2 pair or 4 pair (only on 24V/48V model)
Dimensions (unit=mm)

Specification
Standards
IEEE802.3 10Base-T
IEEE802.3u 100Base-TX/100Base-FX
IEEE802.3ab 1000Base-T
IEEE802.3x Flow Control and Back pressure
IEEE802.3at PoE/PSE
Switch Architecture
Store and Forward
DIP Switch
1. Select 2 pair or 4 pair (only on 24V/48V model)
2. Mode A or B
3. Standard power budget
4. High Power budget
Connectors
RJ-45 Socket: CAT-5 (10/100/1000Mbps) Twisted Pair cable Auto MDI/MDI-X
and Auto-Negotiation Function Support
LED
PW1 (Green); PW2 (Green); PoE (Yellow)/ Flashing (overload)
Power Supply
Terminal Block x 2
Input Voltage: 48VDC (802.3af); 54VDC (802.3at)
Input Voltage : 12V ~56V DC (12V model)
Input Voltage : 24V ~56VDC (24V model)
Power Consumption
2 Watts max
PoE Budget
12V model : 30W (2 pairs)
24V & 48V model : 60W
Operating Humidity
5% ~ 95% (Non-condensing)
Operating Temperature
-40°C~75°C / -40°F~167°F
Storage Temperature
-20°C~70°C / -4°F~158°F
Case Dimension
Metal case. 32 (W) x 81.5 (D) x 104 (H) mm
Installation
DIN Rail and Wall Mount* Design
EMI & EMS
FCC Part 15 Class A, CE
Warranty
5 years
*Optional