Lantronix UDS1100 User manual

UDS1100 Quick Start Guide
For the latest documentation, FAQs and
firmware updates, visit www.lantronix.com

UDS1100

UDS1100
QUICK START C NTENTS
What’s In the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
IP Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Install the Deviceinstaller GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Assign IP Address and Configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LEDs/Troubleshoot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Quick Start Guide
UDS1100
2
WHAT’S IN THE B X
In addition to the UDS, the box contains the following items:
P WER SUPPLY (D MESTIC UNITS)
PART # C MP NENT DESCRIPTI N
520-079-R Power cube, 110 VAC
500-163 Serial Cable
CD
Power Cord Restraint
P WER SUPPLY (INTERNATI NAL UNITS)
PART # C MP NENT DESCRIPTI N
520-080-R* Power cube, 100-240VAC, with international adapters
500-163 Serial Cable
CD
Power Cord Restraint
* Not included wit UDS1100 POE version
D CUMENTATI N:
CD-ROM containing User Guide and software utilities and Quick Start Guide.

The UDS products allow serial devices to connect and communicate over an
Ethernet network.
This Quick Start explains how to connect, configure, and troubleshoot your
unit using a network connection and our DeviceInstaller software. For more
detailed information or alternative configuration methods, refer to the User
Guide on the CD.
PIN UTS
W W W . L A T R O I X . C O M 3
*
*Not included in UDS1100 POE version

4
Quick Start Guide
UDS1100
IP ADDRESSING
Your unit must have a unique IP address on your network. Two ways to assign
an IP are described below.
DHCP
Many networks use an automatic method of assigning an IP address called
DHCP. If you are unsure whether your network uses DHCP, check with your
systems administrator.
The UDS looks for a DHCP server when it first powers up. The UDS has acquired
an IP address if the red LED stops flashing and the green Status LED is on
continuously. You can use the DeviceInstaller software to search the network for
the IP your unit has been assigned by the DHCP server and add it to the list of
Lantronix devices on the network.
If the UDS does not acquire an IP, or you do not use DHCP, you must assign a
fixed IP address.
FIXED IP ADDRESS
In most installations, a fixed IP address is desirable. The systems administrator
generally provides the IP address.
The IP address must be within a valid range, unique to your network, and in the
same subnet as your PC. You will need the following information before you set
up the unit as described in Assign IP Address.
IP Address:
___ ___ ___ ___
Subnet Mask: ___ ___ ___ ___
Gateway: ___ ___ ___ ___

W W W . L A T R O I X . C O M
C NNECT
Complete the following steps in order. Refer to the numbers in the figure below.
1. Connect a serial device to your unit.
2. Connect an Ethernet cable to the RJ45 port.
3. For standard UDS1100 units, supply power to your unit using the power supply
that was included in the packaging.
4. For the UDS1100-POE version, power is supplied to your unit over the Ethernet
interface using an 802.3af POE compliant power source such as a POE mid-
span or POE Ethernet switch.
Note: T e required input voltage
is 9-30 VDC (center +) or
9-24 VAC (1.5W maximum
power required).
INSTALL THE DEVICEINSTALLER GUI
1. Insert the CD into your CD-ROM drive. If the CD does not launch automatically:
a) Click the Start button on the Task Bar and select Run.
b) Enter your CD drive letter, colon, backslash, Launch.exe (e.g., E:\Launch.exe).
2. Click the DeviceInstaller button.
3. Respond to the installation wizard prompts.
5
Ethernet, Power, and Serial Connections

6
Quick Start Guide
UDS1100
ASSIGN IP ADDRESS AND CONFIGURE
1. Click the Start button on the Task Bar and select Programs ‹Lantronix ‹
DeviceInstaller ‹DeviceInstaller. The DeviceInstaller window displays.
2. Note the device IP address.
3. Access Web Manager by entering the device IP address in the address bar
of a browser. The device's factory default username is left blank and factory
default password is the last 8 characters of the Device ID (for devices
manufactured after January 1, 2020) or is left blank (for all older devices).
4. Assign an IP address in the network settings and perform other
configuration.
Note: Please see your product's User Guide for detailed instructions on
configuration.

W W W . L A T R O I X . C O M 7
LEDS/TR UBLESH T
The unit contains the following LEDs:
• Power
• 10/100 Mb Link
• 10/100 Activity
• Diagnostics
• Status Channel 1
Simultaneously lit red and green LEDs means something is wrong. If the red
LED is lit or blinking, count the number of times the green LED blinks between
its pauses. The following table explains the LED functions.

8
Quick Start Guide
UDS1100
SERIAL LEDS MEANING
10/100 Mb Link steady green Valid network connection
10/100 Activity blinking Network packets transmitting and receiving
Diagnostic steady red and 3 blinks = Network controller error
status blinking green 4 blinks = EEPR M checksum error
5 blinks = Duplicate IP address on network
Diagnostic blinking red and 5 blinks = No DHCP response
Status blinking green
Status steady green Serial port not connected to network
Status blinking green Serial port connected to network