Lanzar VBD 1500MP User manual

OWNER’S MANUAL
Mobile Audio System
• PLL Synthesizer Stereo Radio
• Digital Compact Disc Player
• Automatically Memory Storing
• Preset Equalization
•MP3
• Remote Control
• Slide Down Electronic Detachable Panel
VBD 1500MP

2
CONTENTS
Installation .....................................................................................................3
DIN Front-Mount (Method A) ..................................................................................3
Installing the unit ...............................................................................................3
Removing the unit .............................................................................................4
DIN Rear-Mount (Method B) ...................................................................................4
Using the Detachable Front Panel ..............................................................5
Wiring Connection ........................................................................................6
Operation .......................................................................................................7
General Operation ..................................................................................................7
Radio Operation......................................................................................................9
CD Operation........................................................................................................10
MP3 Operation......................................................................................................11
Remote Control Handset ......................................................................................12
Specification................................................................................................13
Trouble Shooting.........................................................................................14

3
Notes:
• Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
• Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front” (conventional DIN Front-
mount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
DIN FRONT-MOUNT (Method A)
Installing the unit
1. Dashboard
2. Holder
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Screw
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap
can be bent by hand to the desired
angle.
7. Plain washer
30˚
(Fig. 1)
1
3
2
182
53
(Fig. 2)
1
2
6
5
4
3
7
INSTALLATION

4
Removing the unit
1. Before removing the frame, press the
(OPEN/CLOSE)button to slide
down the front panel.
2. Frame
3. Insert fingers into the groove in the
right side of the frame and pull out to
remove the frame. (You can also
remove the frame from the left side.)
4. Lever
After removing the frame, press the
(OPEN/CLOSE)button again to
slide up the front panel. Then insert
the levers supplied with the unit into
the grooves at both sides of the unit
as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the
sides of the unit.
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become aligned
(are fitted), and tighten the screws at
2 places on each side.
Use either truss screws (5 x 5mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
3
4
2
2
1
(Open/Close)
1
2
3
4
INSTALLATION

5
To Reinstall the Front Panel
1. When the panel bracket is in slide
down position, insert the front panel
into panel bracket and press
(OPEN/CLOSE)button to slide up.
2. When the panel bracket is in slide up
position, insert a side of the front
panel to its proper position and push
another side into the panel bracket, a
‘click’ sound should be heard.
3. Note that if the front panel fails to lock
in position properly, press control
button may not function and LCD
display may be missing some
segments. Press the
(OPEN/CLOSE)button and then
reinstall the front panel again.
USING THE DETACHABLE FRONT PANEL
To Detach the Front Panel
1. Press the (OPEN/CLOSE)button,
the front panel will slide down.
2. Press the (OPEN/CLOSE)button
again, the front panel will slide up.
3. When the front panel slides down,
press the bottom button of the front
panel upward and pull it out from the
panel bracket.
4. For safekeeping, store the front panel
in the supplied protective case
immediately after being removed.
(Open/Close)
(Open/Close)
Bottom
Button
Bottom
Button
Protective Case
Front Panel
Front Panel

6
GREEN
GREEN/BLACK
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
MAIN UNIT
WHITE
WHITE/BLACK
FRONT Lch
SPEAKER
REAR Lch
SPEAKER
FRONT Rch
SPEAKER
REAR Rch
SPEAKER
Rch RED
Lch WHITE
(GREY)
REAR RCA CABLE
Rch RED
Lch WHITE
(BROWN)
FRONT RCA CABLE
ANTENNA CONNECTOR
RED
YELLOW
BLACK
CHOKE
BOX
BLUE
POWER
ANTENNA
GROUND (B–)
MEMORY
BACK-UP
IGNITION
SWITCH (B+)
(GREEN)
SUBWOOFER CABLE
WIRING CONNECTION

7
Location and Function of Controls
OPERATION
GENERAL OPERATION
• ON/OFF/ILLUMINATE
Switch on the unit by pressing any
button [except (OPEN/CLOSE)
button (7) and EJECT button (24)].
When system is on, press ILL/PWR
button (9) shortly to adjust the
brightness of VFD display, press it for
several seconds to turn off the unit.
• FACEPLATE RELEASE
Press (OPEN/CLOSE) button (7) to
slide down the front panel and you can
press it again to slide the front panel
into the main body or detach the
removable faceplate.
• SOUND ADJUSTMENT
Press SEL button (10) shortly to select
the desired adjustment mode.
5
8
3
9
14 2217 19 20 21 6 15 241613
11 10 121
25
272318 4

8
The adjustment mode will change in
the following order:
For Electrical Volume:
By pressing AUDIO ADJUST button
(11) or AUDIO ADJUST button (12),
it is possible to adjust the desired
sound quality.
For Digital Rotating Volume:
By rotating the knob (11&12) clockwise
or counter-clockwise, it is possible to
adjust the desired sound quality.
• LOUDNESS
Press LOU/BND button (13) to
increase bass output and display will
show “LOUD”. Press it again to
release this function.
• SET THE CLOCK
Press and hold DISP button (15) until
the clock is shown on the display and
flashed. Then press the
TUNE/SKIP/TRACK button (17)
to change hours or
TUNE/SKIP/TRACK button (16)
to change minutes.
• SELECT MODE
Press MODE button (6) to choose
desired listening mode.
[e.g. radio mode to CD (MP3) mode]
• SUBWOOFER
Press MODE/SW button (6) for several
seconds to toggle subwoofer output.
When subwoofer on, display will show
“ SW”. Press it again for several
seconds to release this mode.
• MUTE
Press MUT button (4) to silence the
receiver. Press it again to release the
mode.
• VACUUM FLUORESCENT DISPLAY
Exhibit current frequency and activated
functions on the display (8).
• EQUALIZATION
Press EQ button (1) to turn on
equalization function and to select
desired audio mode. There are four
kinds of mode as below:
• REMOTE SENSOR
Point the remote control handset to
the remote sensor IR (23).
Press the function keys on the handset
to control the system.
• RESET
RESET button (25) is placed on the
front panel and must be activated with
either a ball point pen or thin metal
object. RESET button (25) is to be
activated for the following reasons:
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not
operate.
- Error symbol on the display.
Note: If press RESET button (25), the
unit can’t work yet, please use a cotton
swab soaked in isopropyl alcohol to
clean the socket on the back of the
front panel.
OPERATION
Volume Bass Treble Balance Fader
FLAT CLASSICS POP M JAZZ DSP OFF

9
RADIO OPERATION
• BAND SELECTION
At tuner mode, press LOU/BND button
(13) to select the desired band.
The reception band will change in the
following order:
• STATION SELECTION
Press TUNE/SKIP/TRACK button
(16) or TUNE/SKIP/TRACK button
(17) shortly to activate automatic seek
function. Press for several seconds
until “MANUAL” appeared on the
display, the manual tuning mode is
selected. If both buttons have not
pressed for several seconds, they will
retune to seek tuning mode and
“AUTO” appeared on the display.
• LOCAL/DISTANCE
Press LOC button (2) shortly to select
between local and distant stations.
Local setting for reception of strong
station, and a distant setting for
reception of weaker stations.
This function is in effect during AUTO
SEEK operation.
• MONO/STEREO
Press MON button (3) to select
monaural or stereo (Mono reception
for radio stations). You can sometimes
improve reception of distant stations
by selecting mono operation.
• AUTOMATICALLY MEMORY
STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS button (18) for several
seconds, the radio searches from
the current frequency and checks
the signal strength until one cycle
search is finished. And then 6
strongest stations are stored into the
corresponding preset number
button.
- Program Scanning
Press AMS button (18) shortly to
scan preset station. When the field
strength level is more than the
threshold level of stop level.
The radio is holding at that preset
number for several seconds with
releasing mute, then searches again.
• STATION STORING
Press any one of the preset buttons
(14) (M1 to M6) to select a station
which had been stored in the memory.
Press this button for several seconds,
current station is stored into the
number button.
OPERATION
FM1 FM2 FM3 AM

10
OPERATION
CD OPERATION
• SELECT TRACKS
Press TUNE/SKIP/TRACK button
(16) or TUNE/SKIP/TRACK button
(17) to move to the previous track or
the following track. Track number
shows on display.
Hold TUNE/SKIP/TRACK button
(16) or TUNE/SKIP/TRACK button
(17) to fast reverse or fast forward.
CD play starts from when you release
the button.
• PAUSE PLAYING
Press PAU button (19) to pause CD
player. Press it again to resume play.
• REPEAT THE SAME TRACK
Press RPT button (21) to continuously
repeat the same track. Press again to
stop repeat.
• PREVIEW ALL TRACKS
Press SCN button (20) to play first
several seconds of each track on the
current disc. Press again to stop intro
and listen to track.
• PLAY ALL TRACKS
Press SHF button (22) to play all tracks
on CD in random order. Press again
to cancel the function.
• EJECT
When the front panel is sliding down,
press EJECT button (24) to stop CD
playing and eject the disc from the disc
slot (5).
NOTE ON CD-R/CD-RW DISCS
• On this unit, in addition to an audio
CD, you can play your original CD-R
or CD-RW that contain audio titles.
• However, depending on the conditions
of the recording equipment or the
CD-R/CD-RW disc itself, some
CD-Rs or CD-RWs cannot be played
on this unit.
• DO NOT stick paper or tape, etc. onto
the label side or the recording side of
any CD-R/CD-RW, as it may cause a
malfunction.