lap 24907 Manual

Ref Description Illustration Qty Ref Description Illustration Qty
Head unit,
cable and
connector
Plug, LED Transformer
0.5m cable
Loom and junction box Fixings kit
A
B
C
D
4
8
1
1
1
Adhesive pad
Screw
Tools Required (not supplied)
6mm Cross Headed Screwdriver
Pencil
Before You Start
• Decide on an appropriate location for your product (see siting instructions below).
• Ifyouareinanydoubtaboutinstallingthisproduct,consultaqualiedelectrician.
Siting Instructions
1. This product is designed for use under kitchen cupboards, bookshelves, cabinets etc.
Suitable for indoor use only. Not suitable for bathrooms.
2. Do not attach to surfaces which are damp or freshly painted.
3. The chosen location should allow for the product to be securely mounted and safely
connected to the mains supply (240V wall socket or fused outlet socket).
4. Ensure cables are routed to avoid accidental damage or hazard.
29.07.11 Page 1 of 2
Installation
1. Lay out/ measure the positions of the head units as desired. Ensure you route cables to avoid
accident or damage occurring. Cables can be taped to mounting surface after installation.
2. Each head unit is supplied with 1m of cable. The cable from the junction box to the
transformer lead and plug 2.5m long. See Fig 1 for example layout.
White LED: 24907
Blue LED: 55495
1
Adhesive
pad cut-out
shapes
Theseinstructionsareforyoursafety.Pleasereadthroughthemthoroughly
beforeuseandretainforfuturereference.
Installation and Safety Instructions
LAPLEDDiskdownlightskit4pk

3. Attach heads in position using either the supplied screws or self adhesive pads. If using the
screws to fix the heads you will need to separate the head from the frame. Carefully push on the
rear of the LED unit, towards the edge. See Fig 1. There is a knock out on one edge so the cable
can be laid flat to the surface. Screw the frame to the mounting surface ensuring the cable is
passing through the knock out. When the frame is secure, carefully push the LED unit back into
position.
4. Fix junction box to mounting surface using supplied adhesive pad. Connect all heads to the
junction box, route loom (B) to desired power source (240V mains socket or fused outlet socket
- see connection section below). Take care not to create a trip hazard. Cables can be tidied and
secured to the mounting surface using tape or small clips (not supplied).
5. Connect loom to transformer (C). Fix transformer to surface (secure with supplied screws).
Check all connections are tight.
6. Adjust heads to desired angle and direction. Your lights are now ready for use.
TheseunitsareSafetyExtraLowVoltageandmustnotbeearthed.
Push to separate LED unit from frame
Mounting screw holes
FIG 1
III
Fig 1
E
L
N
Neutral
Live
Fuse
3 Amps
Cord Clamp
BLUE
BROWN
2. It is also permissible to remove the plug and directly wire the prod-
uct to a fused outlet socket. The Brown wire must be connected to the
terminal marked L or coloured red. The Blue wire must be connected to
the terminal marked N or coloured black. Use a 3 Amp Fuse.
Connection
This product can be connected to the mains supply in two ways:
1. Simply plug into a mains socket. If it is necessary to remove the plug
to feed the cable through an external wall, the plug can be disconnect-
ed and rewired as shown here.
Fig 2
Care & Use
• Always switch off or disconnect from the mains when cleaning the product.
• Wipe clean with a soft dry cloth. Never use scourers, abrasives or chemical cleaners.
Do not allow moisture to come into contact with electric parts.
• This product uses LEDs (Light Emitting Diodes) and is maintenance free. The LEDs give
you several years of use without ever needing to changing a bulb. There are no user
serviceable parts in this kit and should malfunction or damage occur, the kit must be
replaced. The LEDs are not replaceable.
Waste electrical products should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice.
Page 2 of 229.07.11 Powersmith Ltd, BA22 8RT