Laser SPK-WCALC-118 User manual

Clock Radio with Wireless Charging
SPK-WCALC-118
User Manual

WHAT’S IN THE BOX
• Clock radio
• 240V Wall power charger
• USB-A to USB-C charging cable
• 3.5mm to 3.5mm audio cable
• Clamp and screw (to secure the power cable)
• User manual

OVERVIEW
15. On/O switch
16. USB-C port (Power)
17. USB-A port (Media)
18. Micro SD card slot
19. AUX port
20. Wireless charging area
1. Mode
2. Clock
3. Alarm
4. Snooze / Brightness adjustment
5. Vol+ / Previous track
6. Vol- / Next track
7. Play / Pause
8. Bluetooth
9. TF (USB / Micro SD)
10. AUX
11. FM radio
12. Alarm 1
13. Alarm 2
14. Low battery

OPERATIONS
Connecting to power
1. Connect the supplied USB-A to USB-C cable
to the clock’s USB-C port.
2. Connect the other end to the supplied 240V
wall power charger.
3. Connect the charger to power.
Wireless Charging
• Place your phone on the wireless charging area
of the clock.
NOTE: The clock must be powered by the mains
power for wireless charging to work.
Set Time
1. Press the button to switch between 12/24-
hour modes.
2. Hold down the button to start setting the
time; the hour digit will start blinking.
3. Press the button to switch between hour/
minute settings.

OPERATIONS
4. Use and buttons to adjust the values.
5. Press and hold the button to save the time.
Set Alarm
1. Press the button to switch between Alarm 1/
Alarm 2 modes.
2. While alarm icon is ashing on the screen,
press and hold the button to start setting
the alarm.
3. Press the button to switch between hour/
minute/On-O/ringtone/volume/snooze
duration settings.
4. Use and buttons to adjust values.
5. Press and hold the button to save the alarm.
Alarm and snooze functions
• Alarms are active when alarm symbols appear
on the display.
• While the alarm is ringing, press the Snooze
button to activate snooze; press any other
button to turn it o.
continued...

• At other times, go through the alarm setting
process to turn on/o the alarm.
Switch Mode
Press the button repeatedly to switch between
Bluetooth /FM radio/Micro SD/USB/AUX modes.
Adjust the display brightness
Press the Snooze button to adjust the brightness
between O, Low, Medium and High. The default
is High.
Control the volume
• Hold down the button to increase the
volume.
• Hold down the button to decrease the
volume.
Select previous/next song
• Press the button to skip to the previous
song.
OPERATIONS
continued...

• Press the button to skip to the next song.
FM Radio Mode
• Press the button to switch to FM mode.
• Long press the button to automatically scan
and save radio stations.
• Press and buttons to select preset
stations.
USB / Micro SD Mode
Insert a USB ash drive or Micro SD card to
switch to the TF mode, or press the button to
switch.
Aux Mode
1. Connect the supplied 3.5mm audio cable into
the clock’s AUX port and the headphone jack
of the external device.
2. Press the button to switch to AUX mode.
OPERATIONS
continued...

BLUETOOTH
Pairing
1. Press the button to switch to Bluetooth
mode.
2. Enable Bluetooth on your connecting device. It
will search for nearby Bluetooth devices.
3. Select “SPK-WCALC-118”.
NOTE: If “SPK-WCALC-118” does not appear
on your connecting device’s screen, try again
from the beginning of step 1.
4. Conrm Bluetooth pairing request on your
connecting device.
5. Now, audio you play on your connected device
should come through the clock’s speakers.
NOTE: The clock only connects to one device at
a time.
Use your device to control music playback and
volume, or use , and buttons on the
clock.

Answer/Hang up a call
When there is an incoming call. Press the
button to answer the call.
Press again to end the call.
Reject a call
When there is an incoming call, hold down the
button to reject the call.
Disconnecting/Unpairing:
• To disconnect, turn o the connected device’s
Bluetooth.
• To unpair (remove the connection entirely), go
to the connected device’s Bluetooth settings,
nd “SPK-WCALC-118” on the list of paired
devices, and select “Forget” or “Unpair”.
BLUETOOTH
continued...

SECURE THE POWER
CABLE
Use the supplied clamp and screw to secure the
power cable.
1. Run the supplied USB-A to USB-C cable
through the clamp.
2. Plug in the cable to the clock’s USB-C port.
3. Attach the cable to the clock by placing the
screw through the clamp, into a recess, and
tightening it.