Laser SOUNDTEC SPK-ST10 User manual

Mini Boombox
SPK-ST10
User Manual

WHAT’S IN THE BOX
• SPK-ST10 Speaker
• USB Type-C Charging Cable
• 3.5mm Aux Cable
• User Manual

Bluetooth Version: 5.0
Bluetooth Range: 10 meters
Bluetooth Name: SPK-ST10
IP Rating: IPX5
USB: Up to 128GB
FM Frequency: 87.5MHz – 108MHz
Signal to Noise Ratio: ≥ 83dB
Frequency Response: 80Hz – 16kHz
Speaker Quantity: 2
Speaker Size: 3.5”
Impedance: 4 Ω
Total RMS Power Output: 10W
Total Peak Power Output: 20W
Battery: Lithium Ion 3.7V 3000mAh
Charging: 5V / 1.5 Amp
Charging Time: 4 hours
Battery Runtime: 4.5 hours (at 50% volume)
Product Dimensions: 360 x 135 x 184mm
Weight: 2.06kg
SPECIFICATIONS

FEATURES
• 2.0 channel sound
• Bluetooth input
• USB input
• FM Radio
• 3.5mm Aux input
• True Wireless Stereo
(two identical speakers
required for pairing)
• Hands free Microphone (built-in)
• RGB lighting
• IPX5 Water resistance
• Built-in rechargeable battery
• Carry handle

CONTROLS

1.
-Press and hold to skip back
track
- Tap to decrease volume.
2.
- Press and hold to skip track
forward.
- Tap to increase volume
3. - Tap to turn RGB lighting
on/off.
4. - Tap to play/pause.

5.
- Tap to switch between
Bluetooth, USB, FM, and
Aux modes.
6.
- Tap during TWS pairing to
connect.
- Tap while connected in
TWS to unpair.
7. - Press and hold to turn
power on/off.
8.
- Connect an external source
input USB.
- Up to 128GB drives
formatted to the Fat32 or
exFAT le system are
supported.

9.
- Connect an external source
input via a 3.5mm Aux
cable.
10.
- Connect a USB Type-C
cable to charge the
speaker.
- A USB wall adapter 5V/2A
is recommended.
11.
- Insert a small pin to reset
the speaker back to factory
settings.

BLUETOOTH PAIRING
• With the speaker on tap the
button until you reach the Bluetooth
mode (the speaker turns on in Bluetooth
mode by default.
• The button should have a blue
ashing light.
• Search for and select “SPK-ST10”
under the Bluetooth settings of device
you are connecting to e.g. smartphone
or tablet.
• Once connected you will hear a tone
from the speaker.
• To disconnect Bluetooth press and
hold the button.
TIP: If password is requested enter
“0000”

• Turn on two identical speakers into their
Bluetooth pairing modes.
• Tap the button on one of the
speakers. The button light will be
ashing.
• The button light will be solid once the
speakers have connected to each other.
• Search for and select “SPK-ST10”
under the Bluetooth settings of a device you
are connecting to e.g., smartphone or
tablet.
• Once paired to a smart device any
music played will come out of both
speakers in separated stereo channel
(dependent on source material).
• Tap the button to exit TWS
function.
TIP: TWS pairing will not work if either of the
speakers are already connected to a device via
Bluetooth. Please disconnect the speakers from
any Bluetooth connections before using TWS.
TWS PAIRING

• Connect an external source device via
the USB-A input on the speaker.
• When connected the speaker will
automatically switch to USB mode.
• Press and hold buttons to skip
tracks or tap to adjust volume.
• Tap button to play or pause.
• Up to 128GB drives formatted to the
Fat32 or exFAT le system are supported.
USB IN

• With the speaker on tap the button
until you reach FM Radio mode
• Press and hold the button to start
the auto search function for FM stations.
• This operation will scan all available
FM stations and record them to memory.
• The scan procedure will take 1- 2
minutes to complete and should not be
interrupted.
• Once complete you can hold the
Volume buttons to skip between the
saved stations or tap to increase/decrease
volume.
FM RADIO

• Connect an external source device via
3.5mm Aux cable.
• When connected the speaker will
automatically switch to Aux mode.
• During Aux connection track controls
will need to be done via the source device.
• To exit Aux mode simply disconnect
the 3.5mm Aux cable.
AUXILIARY IN

• Turn the speaker on and connect to a
smart phone using Bluetooth
(see Bluetooth Pairing instructions).
• When there is an incoming call you can
tap the button to answer the call.
• You can use the built-in microphone
on the speaker to talk.
• Tap the button to end the call.
• To reject an incoming call press and
hold the button.
HANDS-FREE CALLS

• Turn the speaker on and connect to a
smart phone using Bluetooth
(see Bluetooth Pairing instructions).
• Press and hold the button on the
speaker to activate the voice assistant
feature on the connected phone.
• You can use the built-in
microphone on the speaker to issue
commands to the voice assistant.
ACTIVATING VOICE
ASSISTANT

CHARGING
TIP: When the speaker battery is low it will
prompt for recharging.
• Connect a USB Type-C cable to
charge the speaker.
• A USB wall adapter 5V/2A is
recommended however slower
charging via a Computer/Laptop
USB port is possible.
• The 4 LED lights on the top
control panel of the speaker will
illuminate in sequence.
• Once charging has nished the
lights will be solid (if speaker is on).
• A full charge takes up to 4 hours
(dependent on charging source).

TIPS FOR SAFE CHARGING
1. AVOID OVERCHARGING.
Disconnect chargers and devices after
the battery reaches a full charge. Leaving
devices on a charger too long can cause
them to overheat and can reduce battery
life.
2. PICK THE RIGHT CHARGER.
Only use the charger and cable that came
with your device. If no charer was supplied
or using your own charger, always follow
the manufacturer’s recommend charger
requirements. Take special care to match
the correct voltage and amp values your
device requires when picking a charger.
Chargers are designed for specic battery
types; mixing chargers and batteries could
result in unexpected problems.

TIPS FOR SAFE CHARGING
continued...
3. CHARGE ONLY ON
NON-FLAMMABLE SURFACES.
Devices and chargers can get warm or
sometimes even hot during charging.
Make sure to always place the device and
charger on a non-ammable surface when
charging. Do not place on beds, pillows,
paper, or near any fabric such as curtains
or clothing under any circumstances.
4. AVOID EXTREME
ENVIRONMENTS.
Do not recharge your devices in environ-
ments where extreme temperatures can
occur. On particularly hot days do not
charge in places such as the inside of a
car, or an unairconditioned room. If it’s

TIPS FOR SAFE CHARGING
continued...
possible, try and wait till the evening when
temperatures are a bit cooler.
5. MONITOR CHARGING.
Recharge your devices while you are
nearby, preferably in the same room or
another room close by. This way when
there is a defective battery or charger,
you are able to take it off the power
supply immediately.

No Power:
• Check battery level and charge
if required.
• Try turning on speaker while
connected to a power source.
• Try charging the speaker with
a USB Wall Adapter (like a smart
phone charger) instead of a laptop
or computer.
TROUBLESHOOTING