Lava Heat PANDORA Y7 User manual

TABLE OF CONTENTS
Caution ………………………………………………………. 1
Exploding drawing-Y7 ………………………………………. 2
Parts list-Y7…………………………………………………. ..3
Assembly Procedures ………………………….….…………4
Position logs and glass ball on the burner………………… 5
Heater Stand and Location ………………………………… 6
Gas Requirements …………………………………………..6
Leakage Test …………………………………………………6
Lighting instructions …………………………………………7
Storage ……………………………………. ……………….. 7
Cleaning and Care …………………………………………..7
Data badge1………………………………………………….8
Data badge2………………………………………………….9
Problems Check List ………………………………………..10

CAUTION
PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION
FOR INSTALLATION, PLEASE READ THIS MANUAL CAREFULLY
REPAIRS SHOULD BE DONE BY A QUALIFIED SERVICE PERSON ONLY
Do not use this appliance for indoors, as it may cause personal injury or property
damage.
This outdoor heater is not intended to be installed on recreational vehicles and/or
boats.
Appliance should be located on a solid surface.
Maintenance and repair should be carried out by a qualified person.
Improper installation, adjustment, alteration can cause personal injury or property
damage.
Do not attempt to alter the unit in any manner.
Never replace or substitute the regulator with any regulator other than the
factory-suggested replacement.
Do not store or use gasoline or other flammable vapors or liquids in the heater unit.
The whole gas system, hose, regulator, pilot or burner should be inspected for leaks
or damage before use, and at least annually by a qualified service person.
All leak tests should be done with a soap solution. Never use an open flame to check
for leaks.
Do not use the heater until all connections have been leak tested.
Turn off the gas valve immediately if smell of gas is detected.
Do not transport heater while it is operating.
Do not move the heater after it has been turned off until the temperature has cooled
down..
Control compartment, burner and circulation air passageways of the heater must be
kept clean.
Frequent cleaning may be required as necessary.
The LP tank should be turned off when the heater is not in use.
Check the heater immediately if any of the following occurs:
- The heater does not reach temperature.
- The burner makes popping noise during use (a slight noise is normal when the
burner is extinguished).
- Smell of gas in conjunction with extreme yellow tipping of the burner flames.
The LPG regulator/hose assembly must be located in the tank cabinet where LPG
tank located
Any guard or other protective device removed for servicing the heater must be
replaced before operating the heater.
Adults and children should stay away from high temperature surface to avoid burns or
clothing ignition.
Children should be carefully supervised when they are in the area of the heater.
Clothing or other flammable materials should not be hung on the heater or placed on
or near the heater.
1

Exploding Drawing-Y7
2

Parts List-Y7
3
Part No Part Name Qty Part No Part Name Qty
1 Side panel of bottom cupboard 2 21 Inner panel of burner 1
2 Wheel without brake 2 22 Artificial log set 1
3 Wheel with brake 2 23 Outer top connection 1
4 Bottom panel 1 24 Inner top connection 1
5 Back door of bottom cupboard 1 25 Back handle 1
6 Door knob 2 26 Top mash side connection 2
7 Side supporter of combustion
chamber bottom panel
2 27 Top panel 1
8 Bottom door damper 1 28 Pilot protector 1
9 Turn knob bracket 1 29 Top mesh 1
10 Turn knob 1 30 Top panel of combustion chamber 1
11 Outer middle decorated bar 1 31 Side tempered glass 2
12 Gas valve 1 32 Glass slot 1
13 Inner middle decorated bar 1 33 Front tempered glass 1
14 Inner piece 2 34 Pilot 1
15 Inner panel of Top back door 1 35 Pilot bracket 1
16 Outer panel of Top back door 1 36 Front supporter of combustion
chamber bottom panel
1
17 Hinge 1 37 Bottom of combustion chamber 1
18 Back vertical bar 2 38 Front panel of bottom cupboard 1
19 Branket of burner 2 39 Decorated oblate glass ball
20 Outer panel of burner 1

ASSEMBLY PROCEDURES
Take out the heater body and all of the parts from carton, then follow below procedures.
STEP 1 STEP 2
Screw the knob on tank door with screw
we supplied in one set.
Use 2 pcs of M8 screw to contact handrail
with heater body
STEP 3 STEP 4 if go with back wheel
Screw four wheels on heater body, two
wheel without brake for front side and two
for behind.
Position top space mesh on the top board,
then screw it on.
4

Position ceramic logs on the burner
Pandora Y7
1 Take out ceramic logs decorated oblate glass ball from carton
2 Refer to following picture for position the ceramic logs and
decorated oblate glass ball.
` 5

HEATER STAND AND LOCATION
The heater is for outdoor use only. Always ensure that adequate
fresh air ventilation is provided.
Always maintain proper clearance to combustible materials.
Heater must be placed on level firm ground.
Never operate heater in an explosive atmosphere like in areas where
gasoline or other flammable liquids or vapors are stored.
Keep a distance of at least 2 metres from Combustible Materials.
After every use, turn off the gas valve on the cylinder.
The heater should be protected from strong winds by braking the wheel
GAS REQUIREMENTS
Use liquid propane gas only.
The pressure regulator and hose assembly to be used must conform to local standard
codes.
The installation must conform to local codes, or in the absence of local codes, with
the standard for the storage and handling of liquid petroleum gases.
A dented, rusted or damaged propane tank may be hazardous and should be
checked by your tank supplier. Never use a propane tank with a damaged valve
connection.
The propane tank must be arranged to provide for vapor withdrawal from the
operating cylinder.
Never connect an unregulated propane tank to the heater.
LEAKAGE TEST
Gas connections on the heater are leak tested at the factory prior to shipment. A complete
gas tightness check must be performed at the installation site due to possible mishandling
in shipment or excessive pressure being applied to the heater.
Make a soap solution of one part liquid detergent and one part water. The soap
solution can be applied with a spray bottle, brush or rag. Soap bubbles will appear in
case of a leak.
The heater must be checked with a full cylinder.
Make sure the safety control valve is in the OFF position.
Turn the gas supply ON.
In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas
supply on and recheck.
Never do leak test while smoking.
6

LIGHTING INSTRUCTIONS
Open the cabinet door, put the gas cylinder into the cabinet
Turn the control knob clockwise to “OFF” position.
Connect the regulator to the gas bottle. Turn the gas supply “ON” at the cylinder.
Check with the use of soapy water for any gas leakage between the bottle and the
regulator
Push down the control knob and keep pressing whilst turning anti-clockwise to the
“Ignition” position (a click will be heard), this will light the pilot. If not repeat this
process.
When the pilot burner is lit, keep the control knob pressed for 5 seconds then release
it.
If the burner does not stay alight, repeat steps 3 and 4. If the burner has not lit wait 5
minutes and repeat steps 3 and 4.
Adjust the heat setting by turning the control knob to the high or low position.
To turn the heater ‘OFF’ turn the cylinder valve or regulator switch to the ‘OFF’
position and then turn the control knob on the appliance clockwise to the ‘OFF’
position.
WARNING:
If the burner fails to ignite, turn the control knob off (clockwise) and also turn the cylinder
valve off. Wait five minutes before attempting to relight with ignition sequence.
CLEANING AND CARE
Make sure all the cleaning is done after turn off the heater and cooling down.
Wipe off powder coated surfaces with soft, moist rag.
Do not clean heater with cleaners that are combustible or corrosive.
Remove debris from the burner to keep it clean and safe for use.
Open the top back door to clean debris on glass carefully.
STORAGE
1. Always close the gas valve of the gas cylinder after use or in case of a disturbance.
2. Remove the pressure controller and the hose.
3. Check the tightness of the gas valve and for damage. If you suspect a damage, have it
changed by your gas dealer.
4. Never store liquid gas cylinder in a sub-terrain, or at places without adequate air
ventilation
7

DATA BADGE FOR THE Y7 MOBILE PATIO HEATER
APPLIANCE CODE: Y7
TOTAL HEAT INPUT: BTU
GAS CATEGORIES: I3+ I
3B/P(30)
TYPES OF GAS: Butane Propane LPG mixtures
GAS PRESSURE: 28 – 30 mbar butane
37 mbar propane
30 mbar LPG mixtures
INJECTOR SIZE: 1.45 mm 1.45 mm
FOR USE OUTDOORS AND IN WELL VENTILATED AREAS
THIS APPLIANCE IS NOT FOR DOMESTIC USE
WARNING: ACCESSIBLE PARTS MAY BE VERY HOT. KEEP YOUNG CHILDREN
AWAY
READ THE INSTRUCTION LITERATURE BEFORE USING THE APPLIANCE. THE
APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE
INSTRUCTIONS AND LOCAL REGULATIONS
CLOSE THE VALVE OF THE GAS CYLINDER OR THE REGULATOR AFTER USE.
THE USE OF THIS APPLIANCE IN ENCLOSED AREAS CAN BE DANGEROUS
AND IS PROHIBITED
WELL VENTILATED AREAS MUST HAVE A MINIMUM OF 25% OF THE SURFACE
AREA OPEN. THE SURFACE AREA IS THE SUM OF THE WALL SURFACE.
8

DATA BADGE FOR THE Y7 MOBILE PATIO HEATER
APPLIANCE CODE: Y7
TOTAL HEAT INPUT: 61000BTU
GAS CATEGORIES: I3B/P(50)
TYPES OF GAS: LPG mixtures
GAS PRESSURE: 50 mbar LPG mixtures
INJECTOR SIZE: 1.30 mm
FOR USE OUTDOORS AND IN WELL VENTILATED AREAS
THIS APPLIANCE IS NOT FOR DOMESTIC USE
WARNING: ACCESSIBLE PARTS MAY BE VERY HOT. KEEP YOUNG CHILDREN
AWAY
READ THE INSTRUCTION LITERATURE BEFORE USING THE APPLIANCE. THE
APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE
INSTRUCTIONS AND LOCAL REGULATIONS
CLOSE THE VALVE OF THE GAS CYLINDER OR THE REGULATOR AFTER USE.
THE USE OF THIS APPLIANCE IN ENCLOSED AREAS CAN BE DANGEROUS
AND IS PROHIBITED
WELL VENTILATED AREAS MUST HAVE A MINIMUM OF 25% OF THE SURFACE
AREA OPEN. THE SURFACE AREA IS THE SUM OF THE WALL SURFACE.
9

10