lavatools Javelin Pro User manual

QUALITY THERMOMETERS
CALIFORNIA USA
PRO
javelin

01
02 05 06
04
03
YOUR JAVELIN PRO

STABILIZATION ALERT
Insert the probe into your food and hold the
icon. The word HOLD will start blinking
and after a few seconds, a double chime will
sound when the temperature has stabilized.
The stabilized temperature remain on the
display as long as you are holding the icon.
Release your finger to return to normal.

MAX/MIN
Double tap the icon to display the maximum temperature
for current session. Tap again for the minimum temperature.
To exit, tap again.
Hold the icon during MAX/MIN to clear values.

POWER SAVER
Hold the icon to enable power saving
mode. This will disable the backlight and
reduce power consumption.
Press and hold the icon
again to exit this feature.

CHANGING THE BATTERY
When the display shows “ERROR” and
the icon, it’s time to switch out your
battery. Fully retract the probe and twist
open the battery door with a coin.
Carefully remove existing battery and
insert a new CR2032 with the positive
(+) pole up.
MODEL: PX1 LAVATOOLS. CALIFORNIA Assembled in China
MEASURING
RANGE:
-40°F ~ 482°F
-40°C ~ 250°C
TOUCH SENSOR:
Single tap for backlight
Double tap for MIN/MAX
Hold for Stabilization Alert
C
R
2
0
3
2

ADDITIONAL INFORMATION
Sleep Mode
If left on and idle for more than 60 minutes, the Javelin PRO will
automatically go to sleep. Simply tap the touch pad to wake the device.
Antifog Display
The display is coated in a hydrophobic agent to keep the readout
fog-free even when measuring steaming liquids. For this reason, we do
not recommend scouring cleaning products as it will strip the coating.

Magnetic Backing
The Javelin PRO has a built-in magnetic backing to allow for convenient
storage. Magnetic backing may not work on stainless steel surfaces.
Antimicrobial Coating
Silver-based antimicrobial additive is impregnated into the plastic shell to
inhibit the growth of pathogens. Ecacy is rated at 99% or greater.
Tapered Sensor Tip
The ultra-sensitive thermistor sensor is located at the tip of the probe,
requiring a minimum insertion distance of 0.25” (5mm).

PERSONALIZATION
Personalize your Javelin PRO using switches found inside the
battery bay. You can disable and re-enable various functions by
toggling their respective switches. You must turn o the device
to have these changes apply.
toggle
C°/ F°
toggle
auto-o
toggle
stabilization alert

ACCURACY TEST
To check the accuracy of your Javelin PRO, we recommend
using an ice bath test. To create an iced bath, fully pack a large
cup with crushed ice. Next, fill 3/4 of the cup with purified water.
Let the slurry sit for a brief moment and give it a quick stir to
allow the temperature to equalize throughout. Insert the tip of
the probe into the very center of the cup and stir gently. In 3 to
4 seconds, the display will read within 1°F (0.5°C) of 32°F (0°C).

WON’T
SWITCH ON
retract and extend
probe or change
battery
NO
BACKLIGHT
ensure battery
saving mode is
disabled
DISPLAYING
“ERROR”
battery is running
low, change
batteries
CHANGE
C°/ F°
use switch 1 to
switch between
C°/ F°
(see page 10)
TROUBLESHOOTING

DEVICE
ASLEEP
tap on touch pad
to wake device
RESTORE
FACTORY
SETTINGS
turn o device
and position all
personalization
switches
downwards
DON’T HEAR
DOUBLE
CHIME
make sure to hold
the touch pad
long enough
“HOLD”
DOESN’T
BLINK
use switch 3 to
activate
stabilization alert
(see page 10)

USE & MAINTENANCE
• Do not insert the probe all the way to the plastic collar
• Always measure at the center of the meat, avoid hitting bone or hard cartilage
• Prevent bacterial growth by wiping down the probe after each use
• Clean the body with soft damp cloth. Do not use solvents or scouring agents
• Do not put the device in the dishwasher
This device is exclusively intended for the field of application described
in this manual. It should only be used as described within these
instructions. Abuse, water damage, modification, or accidental breakage
to the product will void all warranty.

SAFETY WARNING
• Never leave the device in the oven
• Never place probe directly over fire
• Never immerse the device in liquid for any period of time
• Keep the device and battery out of reach of children
• Do not subject the device to extreme temperature, vibration, or shock
• Batteries must not be thrown into the fire, short-circuited, taken apart or recharged

LAVATOOLS.CO
come visit us for more info
v1.1