Lec+ Contour User manual

Contour & Contour LX Pedicure Chairs
USER MANUAL
1-400-0009 • Rev G • 8/28/22
© Living Earth Crafts 2020, All Rights Reserved
*shown with oponal accessories and/or nishes
Contour LX
Contour

© Copyright 2020
Living Earth Cras®
All rights reserved. is document or any
portion thereof may not be reproduced
in any way, including photocopying or
translation to another language without
the prior written permission from Living
Earth Cras.
Living Earth Cras® is a registered trade-
mark of Earthlite Massage Tables, Inc.
Legal Notice
e information provided in this document is intended
for informational purposes only and is subject to change
without notice. e information provided in this docu-
ment should not be construed as a commitment by
Living Earth Cras®.
Living Earth Cras® assumes no responsibility for the
accuracy or suitability of the information contained in
this document. is document may contain technical
inaccuracies or errors. Living Earth Cras® makes no
expressed or implied warranties of any kind concerning
the information contained in this document, including,
but not limited to, the implied warranties of merchant-
ability and tness for purpose.
Living Earth Cras® shall not be liable for incidental or
consequential damages in connection with or arising out
of the product, performance, or use of this document
and the information and material it describes.

Introduction
Congratulaons on your purchase of the Contour pedicure chair. The Contour oers an
unparalleled pedicure and hydrotherapy experience, featuring a luxurious, handcraed
motorized chair and a tub powered by the patented Sanijet® pipeless jets. The tub basin is lined
with soothing textured foot pebbles to give your client’s feet a relaxed, massaging sensaon.
The Contour is designed for licensed therapists and technicians and is intended to be used in a
professional spa, salon, or similar commercial environment. While no special training is needed
to operate the product, for safety reasons it is important that the instrucons contained in this
manual are reviewed in detail before the rst use. This manual should be read in its enrety by
each professional who will be operang the product to ensure the safety of both operator and
client. This manual should be saved for future reference.
The Contour should not be used in any other manner than described in this manual. Please read,
understand, and follow all safety warnings, labels, and instrucons. Misuse, use of unnecessary
force, or using the chair for unintended or unauthorized procedures can result in injury to
operator, client, and/or equipment.
Detailed instrucons for use and maintenance can be found in this user manual. If you have
further quesons, please contact us at [phone] for US customers, or [phone] for
internaonal customers. We can also be reached via e-mail at info@livingearthcras.com
Secon 1: Safety Informaon
Safety Symbols/Warnings
Secon 2: Product Overview
Product Diagram
Product Specicaons
Secon 3: Operang Instrucons
Control Panel Operaon & Electric Back Tilt
Jets & Lights
Water Fill Valve, Drain & Discharge Pump
Side Trays
Relaxor
Secon 4: Care & Maintenance
Ongoing Maintenance
Tub Cleaning Guide
Troubleshoong
Warranty Informaon
Electrical Specicaons
ETL Mark
FAQs
Contact Us
2-3
4
5
6
7
8
9
10
11
12
13
14
15
15
16
back cover
Table of Contents

READ AND SAVE THESE INSTRUCTIONS
2
IMPORTANT SAFETY INSTRUCTIONS - FOR COMMERCIAL USE ONLY
Read all instructions before using this product.
Safety Symbols
Familiarize yourself with the following
Safety & Warning symbols. They are
designed to prevent damage and injury to
you, your clients, and your new Earthlite
product.
IMPORTANT: The important safety
instructions and warnings in this manual
cannot cover all possible problems and
conditions that can occur. Use common
sense and caution when installing,
operating, or maintaining this appliance.
Indicates an imminently hazardous
situation which could result in serious
or fatal injury.
Indicates a potentially hazardous
situation which could result in serious
injury.
Indicates a potentially hazardous
situation which could result in
equipment damage and/or injury.
SECTION 1: SAFETY INFORMATION
RISK OF ACCIDENTAL INJURY OR DROWNING. DO NOT USE
DRUGS OR ALCOHOL BEFORE OR DURING USE. CHILDREN
OR HANDICAPPED PERSONS SHOULD NOT USE WITHOUT
SUPERVISION.
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above
the body temperature of 98.6°F or 37°C. The symptoms of hyperthermia include an increase in the internal
temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include:
a) Failure to perceive heat,
b) Failure to recognize the need to exit the hydromassage bathtub,
c) Unawareness of impending hazard,
d) Fetal damage in pregnant women,
e) Physical inability to exit the hydromassage bathtub, and
f) Unconciousness resulting in the danger of drowning. WARNING - The use of alcohol, drugs, or
medication can greatly increase the risk of fatal hyperthermia.
WARNING - RISK OF ELECTRIC SHOCK - Do not permit electric appliances (such as hair dryers,
lamp, telephone, radio, or television) to be within 5 ft (1.5m) of this unit.
WARNING - RISK OF INJURY - Exercise care when using a foot bath. Use this product for its
intended purpose: a manicure chair and ll and drain indoor commercial appliance for foot and ankle hydro
massage. DO NOT use attachments not recommended by manufacturer.
WARNING - MOVABLE PARTS, RISK OF INJURY:
• Keep children away from adjustable seat armrests, tilt back, and seat slide, and footrest.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons:
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled
persons. DO NOT leave children alone or allow them to operate the controls. Keep controls out of
reach of children. DO NOT allow children to crawl behind the chair.
• Never use this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination
and repair.
• Keep the cord away from heated surfaces.
• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, etc.
• Never drop or insert any object into any opening.
WARNING - RISK OF HYPERTHERMIA AND POSSIBLE DROWNING. WATER
TEMPERATURE IN EXCESS OF 38°C or 100.4°F CAN BE INJURIOUS TO YOUR HEALTH.
CHECK AND ADJUST WATER TEMPERATURE BEFORE USE.

READ AND SAVE THESE INSTRUCTIONS 3
SECTION 1: SAFETY INFORMATION
• DO NOT reach for any electrical object that has fallen into the water. Unplug immediately.
• DO NOT drop or insert anything into jet opening.
• DO NOT operate without the complete jet assembly installed or without water lled 1 inch above jets.
• DO NOT overll the basin.
• DO NOT stand on or in the basin, or on the foot rest.
• DO NOT leave this appliance unattended when in operation.
• DO NOT use outdoors.
• Keep the electrical cord away from heated surfaces.
• Connect this appliance only to a properly grounded outlet.
• To avoid injury, exercise care when entering or exiting the chair and foot bath.
• Use caution when making positioning adjustments to your chair. Keep all equipment and body parts
away from moving parts while making any adjustments.
• It is important that you clean and disinfect the jets and basin after every use.
• Hydrotherapy should be pleasant and comfortable. Should you or a client experience any pain or
discomfort while using the foot bath, discontinue use immediately and consult a physician.
• You or your clients should consult a physician if diabetic, have poor circulation, if feet or legs are in-
amed, have an open wound, or if you have questions about whether you should be using hydro mas-
sage equipment.
• A qualied plumber and electrician are strongly recommended to install your foot bath.
• Make certain that the cord and plug are maintained in good condition and are not allowed to become
damaged while in use. Avoid positioning the cord in the trafc lane and it is always kept out of the way.
Take this furnishing out of service immediately if the cord or plug becomes damaged in any way.
• Do not attempt to repair. All repairs must be performed by an authorized service representative.
• Chair and tub are to remain right side up. At no time should chair or tub be turned on it’s side or upside
down.
1. RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a ground-fault
circuit-interrupter.
2. Grounding is required. The unit should be installed by a qualied service
representative and grounded.
This product must be grounded. If it should malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock. This product is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
Improper connection of the equipment-grounding connector can result in a risk of electric shock. Check
with a qualied electrician or serviceman if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the product - if it will not t the outlet, have a proper outlet installed by
a qualied electrician.
INSTALLATION INSTRUCTIONS / GROUNDING INSTRUCTIONS
Reset
Button
GFCI Outlet
Grounding Pin
Test
Button
See Installation Manual for full
installation instructions

SECTION 2: PRODUCT OVERVIEW
4
Pillow
Shroud
Side Tray
Receivers
Sprayer/Fill
Water Fill
Valve
Control Panel
*Chair shown with oponal nishes
Footrest
Light
Tub Basin
Drain Handle
Armrest Door
Backrest Cushion
Back Tilt Control

*Measurements may vary due to natural material variaons.
5
Feature Standard Oponal
Pipeless Jet X
Reexology Fiberglass Tub X
Fully Motorized Seat and
Footrest X
Motorized Retractable
Armrest Doors X
Embedded Control Panel X
Power Drain/Discharge
Pump X
Relaxor® Heat & Massage X
Side Trays X
ADA Compliant X
Avonite Standard Opons Upgraded Opons
Upholstery Naturso™ Promessa® or
Ultraleather®
Included Features
Product Specications
Overall Width 32.5” (78.7 cm)
Shroud Width 22” (55.8 cm)
Shroud Height 15” (38.1 cm)
Length (armrest doors open) 73” (185.4 cm)
Length (armrest doors closed) 57” (144.8 cm)
Armrest Door Height 29.25” (74.3 cm)
Seat Height 21” (53.3 cm)/19” (48.3 cm) with ADA cushion
Control Panel
SECTION 2: PRODUCT OVERVIEW
Footrest

SECTION 3: OPERATING INSTRUCTIONS
Control Panel Operation
Slides seat fully
forward & opens
armrest doors
Your Contour control panel is connected and ready for use. See below for descripons of
each buon funconality. For the top row of buons, push and hold the buon unl the
chair movement stops - this means you have reached the memory posion. For the lower
set of buons, push and hold unl the desired posion is reached.
Always use extreme cauon when making any posion adjustments to your
chair. Ensure all body parts and objects are clear from all moving parts.
6
Closes armrest
doors
Seat memory
position 1*
(appx 2” back from
“open” position)
Seat memory
position 2*
(appx 4” back from
“open” position)
Raise
Footrest
Lower
Footrest
Slide Seat
Backward*
Slide Seat
Forward
Electric Back Tilt
The electric back lt buons are conveniently located on the inside of the le armrest door,
where clients can easily make lt adjustments themselves. See below for descripons of buon
funconality.
*NOTE: If the “Slide Seat Backward”, “Memory posion 1”, or “Memory posion 2” buons
aren’t working, ensure the armrest doors ARE FULLY CLOSED. These buons will not acvate if the
armrest doors are at all open. Posions are preset at factory and cannot be changed.
Decrease Seat
Back Tilt
Increase Seat Back Tilt
Increase Seat
Back Tilt
Reset Instrucons: If your chair requires reset, hold “Memory posion 2” buon for
approximately 1 second, this will place the chair in posion 2. Chair is now reset.

SECTION 3: OPERATING INSTRUCTIONS
7
Chromasoothe Light
Pressing the light bu on once will turn the light to the default Bright White color. Press the
switch again to cycle to the next color mode, in the following order:
1. Bright White
2. Aqua Blue
3. Soothing Blue
4. Ocean Blue
5. Majes c Gold
6. Shamrock Green
7. Fiery Red
8. Chameleon Mode
9. Party Mode
To reset, turn lights o for 5 seconds and turn back on. Lights will  ash 4  mes and return to
Bright White.
Jets On/Off Button Chromasoothe Light Button
Jet System
The pipeless “magne c” system is standard in your pedicure unit. A er the basin is  lled to
the proper level, turn jet on by pressing the chrome bu on next to the watever valve marked
“JET”. To turn o , press “JET” bu on a second  me.
NOTE: Liners can be used on a “magne c” system. The liner has to sit between the motor
housing and the wet end assembly.
The jet assembly must be correctly assembled or it may be damaged. This
will NOT be covered by any Con nuum warranty. Never turn the jet on
without adequate water in the basin. There must be at least one (1) inch of
water above the motor housing.
Correctly
placed
impeller
Jet
Cover
Jet housing

SECTION 3: OPERATING INSTRUCTIONS
8
Discharge Pump (Optional)
Drain Knob
Turn the drain knob clockwise to close the drain when  lling the tub. Turn the knob
counterclockwise to open the drain and empty the tub.
Water Fill Valve
There is no automa c shuto with the water  ll valve. You MUST turn the
valve OFF a er the tub is  lled to prevent over ow and/or  ooding. Do not
walk away from the tub when it is  lling with water.
Down-OffUp-FillLeft-Hot Right-Cold
The water  ll valve is OFF when poin ng DOWN. Water dispenses when you pull the valve UP.
Hot water is dispensed when the valve is turned to the RIGHT. Cold water is dispensed when
the valve is turned to the LEFT.
Discharge pump bu on is located on the control panel. Before pressing the bu on, open
the drain with the drain knob and let the water start draining towards the pump. Wait
approximately 5-10 seconds for the pump to register, then push the discharge pump bu on.
Drain Knob
- Turn right to close
- Turn left to open
Discharge Pump
Button

SECTION 3: OPERATING INSTRUCTIONS
Installation
Side Tray
Receivers
1. Locate the side tray receivers on
the side of your chair
2. Push side tray posts evenly into
the receivers
Storage
1. Locate the storage receivers on
the back of your chair
2. Push side tray posts evenly into
the receivers 9
Side Trays (Optional)
Side trays are a convenient way to oer manicure services in your pedicure chair. Each tray has
2 posts that t into receivers on the armrest door. See below for installaon and storage.
Storage
Receivers

SECTION 3: OPERATING INSTRUCTIONS
10
Relaxor® Heat & Massage (Optional)
The following diagrams illustrate the ease-of-use and funconality that the Relaxor® system
provides to you and your clients.
SELECT
WA
VE
PULSE
Ultra
PWR
LO HI
1
2
3
Power
Lower Back Heat - High
Lower Back Heat - Low
Massage All Zones - Connuous
Massage All Zones - Sequenal
Massage All Zones - Short Bursts
Raise Massage Intensity
Raise Massage Speed
Upper Back Massage
Mid Back Massage
Low Back Massage
Lower Massage Intensity
Lower Massage Speed
RISK OF ELECTRIC SHOCK
Keep hand control and all electrical components away from water.
PWR
PWR
• Massage 15 Minute Timer (Standard)
• Massage 30 Minute Timer (Hold Down Button)
• Indicates Active Button
• Indicates Normal Standby
• Indicates High Mode
• Indicates Low Mode
Green Light
Blue Light
Red Light
Orange Light
Symbol Description

SECTION 4: CARE & MAINTENANCE
11
YOU ARE REQUIRED TO CHECK WITH YOUR STATE BOARD FOR MANDATORY CLEANING AND
DISINFECTING REQUIREMENTS AND PROCEDURES.
The following procedures are important guidelines that will help in keep your product clean and
trouble free for years. It is extremely important to clean and disinfect every pedicure chair aer
each pedicure and aer the last pedicure of the day. (See next page for instrucons.)
Cleaning & Ongoing Maintenance
DO NOT USE acetone, paint thinner, bleach, “Armor All” type cleaners, or
industrial cleaners for ANY part of your chair, tub, or components.
DO NOT place nail care products on the tub.
Extended exposure to chemicals like bleach can damage the basin, footpad, and/or upholstery.
Failure to comply with all cleaning instrucons can cause damage and void your warranty.
Category Care/Maintenance Recommendation
Formica
Finishes
Formica nishes require very lile maintenance. Wipe dry any water that
may splash onto the Formica.
Most Dirt &
Residue
Use soapy water, ammonia based cleaner, (not window cleaner) rinse and
wipe completely dry. Commercially avail- able solid surface cleaners, such as
Clean Encounters will also work well.
Prevent Hard
Water Marks Rinse and wipe completely dry aer cleaning.
Remove Hard
Water Marks
Use cleaner formulated for removing hard water marks, such as CLR or
Lime-A-Way.
Stubborn
Dirt, Stains, or
surface imper-
fecons
Occasionally stains will not be removed by the above steps, in this case the
use of a Mr. Clean® Magic Eraser will allow for a more aggressive cleaning
without damaging the surface nish. Use the Magic Eraser following the
direcons on the package.
Upholstery Simply use a mild detergent (very lile) with warm water and gently clean
any dirt or grime that may appear on the seat, seat back or arms.
Footrests
A mild detergent and warm water is all that is needed to clean the padded
footrests. However care should be taken to prevent nail polish or acetone
from coming in contact with the footrests. These products may damage or
discolor the outer “skin” of the foam. In spite of taking necessary precau-
ons to protect the footrests, hard water and/or certain products many
cause the black footrests to develop a white lm or some discoloraon. If
this occurs, a product called “Black Max”- Vinyl and Rubber Dressing works
well to restore the footrests.
NOTE: DO NOT USE THE NYLON SCOURING PAD ON THE FOOTRESTS.

12
SECTION 4: CARE & MAINTENANCE
Tub Cleaning Guide
YOU ARE REQUIRED TO CHECK WITH YOUR STATE BOARD FOR MANDATORY
CLEANING AND DISINFECTING REQUIREMENTS AND PROCEDURES
The removable wet-end assembly MUST be placed onto the motor housing in the correct
posion of the jet may be damaged. The wet end housing must t in the proper groove onto
the motor housing. If the wet end is not posioned correctly, damage to the jet may occur due
to misalignment. This will NOT be covered by any Connuum warranty. Never turn the jet on
without adequate water in the basin. There must be at least one (1) inch of water above the
motor housing.
Recommended Cleaning and Disinfecting Products
Your state board requires disinfecng of your pedicure basin. Connuum recommends “Splish
Splash One-Step Disinfectant.” While other EPA registered products are available for maintaining
pedicure tubs, we have found Splish Splash to be the most eecve, mul-purpose and
economical product on the market.
Cleaning After Each Client & End of Day
1. Turn o the jet and drain all water from the basin.
2. Aer the motor has completely stopped, twist the cover from the housing to expose the
impeller.
3. Remove the wet end consisng of the cover, impeller, and housing from the jet.
4. Clean all 3 wet end parts with a brush, liquid soap, and water to remove all visible residue.
Reaach all 3 parts to the motor housing, ensuring the wet end is placed in the proper
groove on the jet housing.
5. Fill basin with warm water and add the correct amount of an EPA-registered liquid
disinfectant (Splish Splash strongly recommended). Turn on the jets to circulate the water
for at least 10 minutes, scrubbing all visible residue from the inside walls of the basin with
a sponge/so brush. NOTE: Brushes must be cleaned/disinfected aer each use.
6. Drain the basin, rinse with fresh water, and wipe dry with a clean paper towel.
NOTE: THE ABOVE SHOULD BE FOLLOWED EVEN IF TUB LINERS ARE USED
The use of oil-based products can build up in the whirlpool system causing clogging in the jet
and build up onto the surface of the basin. Adherence to the above cleaning will minimize build
up but the manufacturer recommends not to use mineral oil based products.
Cleaning Every Other Week
1. Fill tub with water and one-third (1/3) cup of 5.25% chlorine bleach for each one (1)
gallon of water. (An alternave to bleach would be an EPA-registered disinfectant with
demonstrated bactericidal, fungicidal, and virucidal acvity.)
2. Turn on the jets to circulate the soluon for 5-10 minutes and then sit for 6-10 hours.
3. Drain the basin, rinse well with fresh water, and wipe dry with a clean paper towel.

SECTION 4: CARE & MAINTENANCE
13
Troubleshooting
Issue Solution
No Power/Not
Operang
1. Ensure the power cord is properly plugged into an operaonal GFCI
power supply/outlet.
2. Check GFCI reset and circuit breakers or fuses.
3. Ensure the outlet in your room is receiving power. This can be done
by plugging in a small appliance and turning it on.
No Power to Jet/
Jet not
Operang
1. Ensure the power cord is properly plugged into an operaonal GFCI
power supply/outlet.
2. Check GFCI reset and circuit breakers or fuses.
3. Ensure impeller is correctly installed in the case.
4. Reset the motors by unplugging the system, waing 5 seconds, then
plugging in again.
Excessive Noise
from Jets
1. Remove jet assembly and inspect for dirt buildup, debris, or damage.
2. Follow cleaning instrucons or replace if necessary.
Water Leakage
1. Check and ensure all visible bolts are ghtened.
2. Call a plumber to determine the source of the leak.
3. If the leak is from the jet system, contact customer service.
This helpful troubleshoong guide will provide you with informaon about how to recognize a
problem with your product, determine possible causes, and nd a soluon.
In the event your specic situaon is not covered in this guide, please contact Living Earth Cras
so our technical support department can assist you. Beyond the troubleshoong guide below, do
not aempt to repair the issue yourself. This can void your warranty.
Unauthorized service will not be covered. Please be sure to contact Living Earth Cras Customer
Service rst at [phone], [phone] Int’l.

14
SECTION 4: CARE & MAINTENANCE
Living Earth Cras (LEC) oers an industry best warranty on all pedicure units.
• Motors and controls, actuators, foam and upholstery are warranted for two
(2) years, including parts and labor unless otherwise noted.
• Glass parts are warranted for one (1) year.
• Accessories and replacement parts are warranted for ninety (90) days from
date of shipment.
Living Earth Cras may repair or replace defecve components at our discreon.
Living Earth Cras will return the warranted product, standard shipping pre- paid, to
customers in the connental US. Internaonal customers are responsible for any ap-
plicable dues and taxes, as well as all shipping charges inbound and outbound.
Excluded from Limited Warranty:
1. Unauthorized repairs.
2. Damage due to freight, accident, natural disaster, and/or abuse.
3. Damage or malfuncons due to improper installaon including but not lim-
ited to, failure to comply with all naonal, state, and local plumbing, electri-
cal, and building codes.
4. Fading, discoloraon, or staining of any part due to improper water addi-
ves, hard water, or harmful cleaning agents or chemicals.
5. Damage to drain pump due to obstrucon in drain hose and/or debris in
pump impeller housing.
All warranes are limited to repair or replacement, at Living Earth Cra’s discreon,
unless otherwise stated. This limited warranty applies only to pedicure chairs installed
in any one of the y (50) States of the United States, the District of Columbia, or
provinces of Canada.
• Jet cover and/or impeller
• Footrest/leg supports
• On/o air actuated buon
• Black plasc parts
• Manicure trays
• Replacement upholstery
• Faucet cartridge and/or ller-sprayer
• Relaxor
• Any LED light
• Handheld control wands
• Any internaonal shipment includ-
ing but not limited to Canada and
Mexico
Parts and/or circumstances for which labor is NOT COVERED - Parts noted below are
simple to replace and DO NOT require a service technician:
Warranty Information

15
SECTION 4: CARE & MAINTENANCE
Electrical Specications
Spec North America Europe/Asia
Input Voltage 120 VAC 220 VAC
Input Frequency 60 Hz 50 Hz
Total Consumpon
- All Opons 11.7 Amps Max 6.1 Amps Max
Consumpon -
Standard Contour 7.7 Amps Max 4 Amps Max
Consumpon -
Relaxor Addional 4 Amps (Max) Addional 2.2 Amps (Max)
Discharge Pump Specication
Motor Design Single-phase synchronous motor
Flow Rate (120V) 24 l/min at 0, 1 bar
Flow Rate (220V) 20 l/min at 0, 1 bar
Duty Cycle Connuous
Power Consumpon See electrical specicaon (next page)
Sanijet® Jet System Specication
Motor Design Single speed, electronic spherical DC motor with magnec rotor
impeller
Motor Materials Thermoplasc jet, motor, and case assembly; stainless steel rotor
impeller
Safety Features Safety shuto sensor, dry-run/thermal overload protecon
Power Consumpon See electrical specicaon (next page)
Conforms to
UL STD 1647
Certied to
CSA STD C22.2
No. 68
5003418
ETL Mark

Does the Contour have backow prevenon?
Yes - see pages 10-11 in Installaon Manual for backow prevenon details.
Do I sll have to install backow prevenon on my main water supply line?
This is enrely dependent on your local and/or state codes. A licensed plumber with knowledge of
your local and/or state codes can answer this queson for you.
Do we need to install a p-trap?
Check with the licensed plumber performing the install. It is dependent on your drain locaon.
Can you provide a leer to my city inspector stang my electrical and/or plumbing setup is
acceptable?
Unfortunately not. In this document, we have provided all the informaon that a licensed plumber
and electrician would need to perform the proper install that adheres to local and state codes. Living
Earth Cras does not have knowledge of all local and state codes and therefore is not qualied to
advise on individual setup quesons. If an inspector has quesons about how your plumbing and/
or electrical is being set up, you will need to contact your plumber and/or electrician.
Does the Contour have GFI/GFCI built in?
There are no GFI/GFCIs built in to the system - we require a GFCI protected grounded circuit to
supply power to the Contour.
Frequently Asked Questions
16

Contact Us
Living Earth Crafts
990 Joshua Way
Vista, CA. 92081
[phone]
[phone] Int’l
[phone] fax
[email protected]
Hours of operation:
Monday - Friday
8:00 a.m. to 5 p.m. PST
Saturday - Sunday
Closed
Visit us online at: livingearthcrafts.com
Join us on
Facebook
Follow us on
Twitter
Connect with us
on Linked In
Follow us on
Instagram