LED Group ROBUS RLEDF30WPIR-24 User manual

Specication:
Installation:
Information for the Product user
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE
marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for
waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is
important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste,
but should be disposed of according to local WEEE regulations
Issue 1 020113
PIR 30W HIGH POWERED LED
FLOOD LIGHT
RLEDF30WPIR-24
Please read instructions before commencing installation and retain
for future reference.
Model No. ：
Depth (mm)：
Width(mm):
Height (mm):
Weight (kg):
Power (W):
Supply voltage:
Colour Temp:
Average Lamp Life:
Insulation:
Ambient temp:
Ingress Protection:
Warranty:
Compliance with:
! Electrical products can cause death or injury, or damage to property. If in any doubt
about the installation or use of this product, consult a competent electrician.
1.Ensure mains supply is switched o before commencing work.
2.Select suitable location for luminaire,
3.Remove bracket from luminaire, mark wall with appropriate xing positions.
Before drilling, ensure that the hole does not impinge on pipe work, cables or
other building services.
4.Mount bracket on wall and re-attach luminaire
5.The luminaire is supplied with 0.5m of rubber cable. Using suitable IP rated
enclosure terminate Brown (Live), Blue (Neutral) and Green/ Yellow (Earth) to
switch supply.
6. Luminaire must be connected to a circuit controlled by an RCD.
7. This product has no user serviceable parts. If any part is damaged, disconnect
from mains and discontinue use.
Note: No “xings screws provided”, please use appropriate xings screws.
The lux and time setting can be customized by moving the appropriate dial.
Time setting adjustable from 10 seconds to 10 minutes and lux setting from day time to
night time.
Detection angle:120°,Dectection distance:8m
Warning: Ensure the distance is at least 5mm between the top surface of the PIR
housing and the bottom of the xture cover avoide the ttting temp.
eect the PIR function.
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
Page 1
ISO 9001:2008
Q UAL IT Y ASS U RED C O MPANY
RLEDF30WPIR-24
135mm
225mm
248mm
2.3kg
30W
220-240V~ 50/60Hz
3000K
30,000 Hours
Class I , Must be Earthed.
-15ºC <Ta < 40ºC
IP54
3 years
EN55015,EN60598-1,EN61000-3-2,
EN61000-3-3,EN61347-2-13,EN61547

225mm
248mm
135mm
At least 5mm
Keep the PIR always under
the tting.
Remove bracket
from luminaire
With 0.5m
of rubber cable
Mount bracket
on wall
Re-attach luminaire
Brown
LN
BlueY./G.
Installation diagram:
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie Page 2
Figure 1 Figure 2
Figure 3 Figure 4
Figure 5 Figure 6
Using suitable IP
rated box
ISO 9001:2008
Q UAL IT Y ASS U RED C O MPANY
Mark wall with
appropriate xing
positions.
Knock expansion bolt into
wall with hammer and then
remove nut from bolt
150mm
75mm