LED World GROW STRIP HH-S2835P-60-24-5M Installation instructions manual

NANO COATED LED GROW STRIP™
24V
DC Power
3.7
WATTS
FOOT
IMPORTANT INSTRUCTIONS
Safety & Warnings
Please read instructions before using product and SAVE THESE INSTRUCTIONS. Before using this product make sure you have right color, product (item number)
and voltage (printed on product). Check for possibility of damage during shipping. If damaged, or wrong product, do not use. Disconnect power before installing
or using.
Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.
THREE YEAR LIMITED LIGHTING WARRANTY
LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other
warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This
Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims
must be submitted to them.
LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected
with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or
otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing
(including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of
the possibility of such loss or damage being incurred.
If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return
authorization number.
ŸDo not power when rolled. Lighting must be installed in a straight line. Do not curl or twist and roll out completely straight before applying power.
ŸOnly install on smooth at surfaces free of burrows that are re retardant.
ŸProduct has an adhesive tape on back. Adhesion can only be made once and the LED strip must fully adhere to surface (ush). Use included clips and screws at
20” intervals to securely fasten strip (in addition to tape adhesive). Failure to do this step will damage product. Rigidly support wires with wire clamps.
ŸDuring installation, do not damage the printed circuit. Exposed wires can cause short circuit damaging product and creating a serious hazard. Do not mount in
a manner or support LED Strip light in a manner that can damage the outer jacket or cord insulation. Do not install this lighting system where the exposed bare
conductors can be shorted or contact any conductive materials. Carefully check that there is no wire cross-over or possibility in the future in area of installation.
ŸTo reduce the risk of re and overheating, make sure all connections are tight.
ŸProduct is sold in the maximum length. Do not exceed 6 meters (19.68”) to one class 2 power supply.
ŸOnly qualied electrician or engineer can perform installation familiar with low voltage wiring techniques. Correct polarity is imperative (+/- is marked on printed
circuit). Parallel connection only.
ŸDO NOT install on ammable material or possibility of in the future. Do not install any luminaire closer than 6 inches (15.25 cm) from any curtain, or similar
combustible materials.
ŸThe light and all its components cannot be mechanically pressed. Never apply to surface above 40c (104F).
ŸVoltage must not exceed 24VDC and must be regulated. The Voltage is printed every 6 LEDS. Check that it is the correct voltage before applying power.
ŸThis is not a toy. Keep out of children's reach.
ŸKeep Flex strip spaced ¾” apart if placing next to each other.
ŸLED Flex Strip is bendable on one at widest plane. Maximum bend radius is 4 inches (100mm) on one plane (at).
ŸNot for use in mission critical, aircraft, emergency signs or lifesaving equipment.
ŸStatic electricity can damage LED(s). Handle with care.
ŸInspect installation after one hour and thereafter regularly.
ŸFor stationary use only and not subjected to possible pressure or movement (or in the future).
ŸNot for in-wall use.
ŸMax. Soldering temperature cannot exceed 250°C (482°F) for a max of 4 seconds. Use 22~20 AWG wire to connect.
ŸUse correct wiring as required by local electrical code. Use a 20 gauge wire to attach to strip by solder (2464 type of wire). Connection to power source may use
Wago™ 222-413 in hardwire applications.
ŸCable lighting systems not be installed in bathrooms.
ŸConductors of extra-low-voltage circuits be rigidly supported.
ŸConductors not be installed in contact with combustible materials and not run through walls, ceilings, oors or partitions, and; Uninsulated conductors not be
installed less than 2.2 m (86”) from the oor.
ŸDo not stare directly into the LED Light. Install LED lighting out of direct sight.
1/5
KG
Never Nail or use Staples
Only power with 24VDC
Class 2 Power Source
Never apply weights or walk on strips
Use only with a listed Class 2 Type power supply.
Disconnect power before installing or servicing (at breaker point).
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations.
Only power with a (listed) constant voltage Class 2 power supply (24V DC).
Never plug into 120V AC. The product requires a optional class 2 Transformer.
1-800-387-4081
ledworldlighting.com ledworld.ca|
Apply to surface at room temperature. Keep
away f r o m ammable ma t e r i a l s . Surface
temperature MAX 40°C (104°F). Don’t install under,
above or near heat sources (i.e. stoves, replaces)
LISTED
Model: HH-S2835P-60-24-5M
Copyright © 2018 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.1 - 11/28/18

2/5
NANO COATED LED GROW STRIP™
1-800-387-4081
ledworldlighting.com ledworld.ca|
Vegetable Plants
LED Grow Strips™
Optimal Grow range is 2 inch ~ 6 inch (50.8mm~152.4mm) from the LED Grow™ Strip to Plant material.
Plant material should not be farther than 30 inches (76cm) from the LED Grow™ Strip.
IMPORTANT LIGHT EFFECTIVENESS INSTRUCTIONS
30” max
Flexible LED Grow Strip™ wrap around
large plant material
Vegetable Plants
about 4”~6” apart
LED Grow Strips™
Mounted with
Corner Cove Channel
20mm
30” max
optimal 2”~6”
Model: HH-S2835P-60-24-5M
Copyright © 2018 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.1 - 11/28/18

3/5
IMPORTANT INSTRUCTIONS
ŸGrowing Plant Material
APPLICATIONS
FLEX STRIP CONNECTION
-
Wire connection using WAGO block connectors
Class 2 Power Source
Alpha XLD Series
AC120V
LED Flex Strip
WAGO
Cut instructions
-
Solder Connection Points
Solder connection points are at marked intervals.
Cut points are at every 6 LEDs (24VDC)
Note Polarity Marks
100mm
+ + + +
- - - -
+
-
-
INSTALLATION PLANNING
LED Flexstrip is a versatile lighting product that can provide a superior lighting solution in a variety of applications.
Recommend design steps before starting the installation process:
General questions based on lighting requirements:
ŸWhere will your power supply be located
ŸHow will you switch your LED lighting ON and OFF?
ŸWhat is the best layout conguration for your installation with wiring consideration?
ŸHow will you run your wiring to your LED strip lighting?
WIRING FOR VOLTAGE DROP
Voltage drop is normal loss of voltage that occurs as power ows along a wire connection in a low voltage systems, and increases as the length of a wire connection is
increased. Wire length and thickness as well as total light wattage inuence the amount of voltage drop.
Recommended maximum wire lengths - 24VDC
Wire Guage (AWG)
20 AWG
18 AWG
16 AWG
20W 30W 50W 60W 90W 100W
27 FEET
42 FEET
67 FEET 45 FEET
28 FEET
18 FEET 11 FEET 9 FEET 6 FEET 5 FEET
8 FEET9 FEET14 FEET17 FEET
27 FEET 22 FEET 15 FEET 13 FEET
WATTAGE CALCULATION
The LED Flex Strips have a label on each roll that indicates the voltage and wattage. You must have the correct Class 2 voltage Power Supply (Transformer) for LED Strip
model. To calculate the wattage, measure the total length of LED Strip in your run multiplied by the wattage of the LED Strip. Remember that a power source should only
operate at a maximum 80% of it rated capacity.
For example : 10 feet of HH-2835P-60-24-5M x 3.7W = 37 Watts
Never Extend the Length of rolls. Rolls are sold in there max length.
IMPORTANT NOTE
Mount Strips on Clean (No Wax/Oil), dry,
smooth, burrows free surface
Download Magnitude app for voltage drop calculations:
Android App iOS App
Note : The LED Grow Strip™ must not be farther than 24” (0.6 meter) from the plant. Ideally plant should be 2”-3” (5cm-7cm) away from the Grow Strip™.
NANO COATED LED GROW STRIP™
1-800-387-4081
ledworldlighting.com ledworld.ca|
Model: HH-S2835P-60-24-5M
Copyright © 2018 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.1 - 11/28/18

4/5
LAYOUT OPTIONS
Note: Always check the Wattage of your LED Strip or Fixture.
Power Supply Wattage x 0.8 = Available Wattage
Class 2 Power Supply
Layout 2
40W18W
Available 80W
18W
Class 2 Power Supply
Layout 3
40W18W
Available 80W
18W
24VDC (100W) 24VDC (100W)
Class 2 Power Supply
24VDC (100W)
Class 2 Power Supply
Layout 1
38W38W 50W 60W
Available 80W Available 80W
24VDC (100W)
Layout with Overload
!
Do Not Use
Securely mount
wires using wire
clamps
LED STRIP CUTTING
Our strips comes with cut mark sign. Strips are be cuttable at each 6 LEDs. Cut
marks lying between set of soldering points.
-
-
--
INPUT
120V AC 60Hz
Regulated Class 2 Power Supply
24VDC LED Flexstrip
+
-
Figure shows LED Flexstrip connected
to a Regulated Class 2 Power Supply
XLD200B-224V-FC
or
LV100-24N-UNV-J
POWERING OPTION
NANO COATED LED GROW STRIP™
1-800-387-4081
ledworldlighting.com ledworld.ca|
CONNECT WITH QUICK CONNECTORS/SOLDERING
There are many options available for connecting LED light strips. Right diagram
shows how connect using our Quick Connectors.
However it is strongly recommend to solder the connection. Please refer to our
quick connector instruction sheet.
+
+
-
-
--
-
Quick Connector
Soldered Contacts
Note: Peel 3M tape before using with Quick Connectors
IMPORTANT NOTE
Polarity marks must match
((+) to(+) and (-) to (-))
otherwise strip will not work
+
-
+
-
Model: HH-S2835P-60-24-5M
Copyright © 2018 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.1 - 11/28/18

5/5
IMPORTANT INSTRUCTIONS
Wrong!
4"
(100mm)
On widest one flat plane (only)
Do not bend sideways.
Flexible on one axis
maximum band radius 4”
MAXIMUM FLEXSTRIP LENGTH SUPPORTED BY OUR CLASS 2 POWER SUPPLY
Power Supply Max Feet of LED Flexstrips Power Supply Max Feet of LED Flexstrips
CVN96L24DC 20.75 Feet (Continuous 77 Watts) XLD200B-224V-FC 2 X 21.6 Feet (Each Channel)
Total 43.2 Feet
NANO COATED LED GROW STRIP™
1-800-387-4081
ledworldlighting.com ledworld.ca|
IMPORTANT INSTRUCTIONS
Apply 1 ½” long electrical heat shrink over all connection points. Secure connection wire with wire clamp.
IMPORTANT !
TROUBLESHOOTING
Tape light strip does not light
ŸMake sure your power supply is turned on and has the correct voltage.
ŸConrm you have the correct polarity (+ to + and - and -) throughout the run of LED Lighting.
ŸHave a electrician check all connections and any switch or dimmer connections from the power supply to the LED Light Strips.
ŸConsider testing with a multimeter to ensure light strip is receiving 24V power.
LED Flex Strip lights blink on, then go off
ŸThe power supply is not adequate for the length of LED Light Strips you are powering. Install a adequate Class 2 power supply.
LEDs farthest from the power supply are noticeably dimmer
ŸThis is the result of voltage drop. Decrease the length of the 24V power feed or use thicker power feed wires between the 24V power supply and the
lighting strips.
Copyright © 2018 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Model: HH-S2835P-60-24-5M
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.1 - 11/28/18