LED World LV-HS 24T2-1 Series User manual

LED CONNECT BARS
Model: LV-HS-XX-24T2-1 & LV-HS-XX-24T2-3 (XX = COLOR NW:Neutral White / WW:Warm White)
D
24V
DC Power
LISTED
use only with
Class 2 Type
power units
MODEL
Safety & Warnings
Before you begin, read all warnings and installation instructions (as they may have been updated from previous versions). Improper installation(s)
present hazards, which can result in personal injury or property damage.
Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.
Use only with Class 2 Type power supply.
Disconnect power before installing or servicing (at breaker point).
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local
regulations. Only power with a (listed) constant voltage Class 2 power supply (24V DC).
ONE YEAR LIMITED LIGHTING WARRANTEE
LED WORLD INC. warranties this product for one year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other
warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This
Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims
must be submitted to them.
LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected
with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or
otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing
(including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of
the possibility of such loss or damage being incurred.
If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return
authorization number.
LV-HS-XX-24T2-Ln
▪COLOR (NW: Neutral White, WW: Warm White)
▪VOLTAGE (24V)
▪LENGTH (Ln=1:12”, Ln=3:40”)
All hard-wire installation and hook-up should be done in accordance with all national and local code. Electrical hard-wire connections must be made by
qualied and licensed personnel. Instructions may change and be updated. Improper installation(s) present hazards, which can result in personal injury or
property damage.
ŸDo not exceed the total combined length of 16 feet of luminaries for 24 Volts DC (when used with a listed Class 2 100 watt LED Driver).
ŸBefore connecting or installing, make sure power is turned off and reduce the risk of fire and overheating, make sure all connections are tight.
ŸOnly install on smooth flat surface. Product must be rigidly mounted with provided clips to surface. A minimum 2 clips per bar.
ŸCorrect polarity is imperative: +/- is marked on the hard-wire and DC barrel connector, center is positive (+)
ŸDO NOT install on flammable material or possibility of in the future. Do not install any luminaries closer than 6 inches (15.25 cm) from any curtain, or similar
combustible materials. Never apply to surface above 40c (104F).
ŸThe light and all its components cannot be mechanically pressed. Do not bend or apply pressure.
ŸVoltage must not exceed 24VDC. Check that it is the correct voltage before applying powering. The voltage must be printed on the LED power supply
(driver). If it is not, do not use.
ŸThis is not a toy. Keep out of children's reach.
ŸKeep LED Bars spaced 1” (28mm) apart if placing next to each other.
ŸNot for use in mission critical, aircraft, emergency signs or lifesaving equipment.
ŸInspect installation after one hour and thereafter regularly.
ŸFor stationary use only. Do not subject to possible movement or pressure (or in the future). Not for in-wall use.
ŸConductors of extra-low-voltage circuits must be rigidly supported.
ŸConnection to power source use Wago™ 222-413 in hardwire applications.
ŸConnect only 24VDC LED bars to other 24VDC LED bar(s) (identical voltage/model).
Ensure applicable wire is installed between driver, xture and any controls in between. When choosing wire, factor in voltage drop, amperage rating and
type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near water (or the possibility of in the future).
Do not modify this product beyond the instructions in this guide or the warranty will be voided.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding with a qualied electrician familiar
with low voltage wiring techniques.
1/2 LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.0-04/28/15
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
1-800-387-4081
ledworldlighting.com ledworld.ca |

LED CONNECT BARS
Model: LV-HS-XX-24T2-1 & LV-HS-XX-24T2-3 (XX = COLOR NW:Neutral White / WW:Warm White)
APPLICATIONS
BENEFITS
ŸIdeal for under counter lighting & cove lighting
ŸArchitectural accenting
ŸExtendable light bar & modular design
ŸNo dark zones and seamless connection
ŸEasy to install with screw mounting brackets and clips
SPECIFICATIONS
Max Voltage 24 VDC (regulated/Class 2)
Watts / Bar 3.2 Watts (12”), 11 Watts (40”)
Length 12” or 40”
Lumens 250~260 Lumens/Bar
OPTIONAL CONNECTORS
LV-HS-PC1-12-DC/SW
Switch control Connector
DIAGRAM
13mm
16mm
Side View
315mm (12”)
INSTALLATION GUIDE
1
2
3
2
3
Mounting clip must be placed within
4" (10cm) end and beginning.
Front Connector
1. Mark on mounting surface to align the LED Connect Bar.
2. Screw and x the mounting clip.
3. Push gently the LED Bar main into the mounting clips
Connect power at one end only! Secure wiring with wire clamps.
Connector
Only connect power to one end!
CONNECTION GUIDE
Low Voltage
Class 2 LED Driver
24VDC (100W)
AC120V
Driver Wattage x 0.8 = total available watts
Use only 24VDC LED Driver with 24VDC LED BARS
Power Connector
LED Bar
Rated Current 0.135A ±5% (12”), 0.5A ±5% (40”)
LEDs 18 (12”), 60 (40”)
OPTIONAL DRIVERS & POWER UNITS (Class 2)
XLD75B-124V-FC (24VDC)
LV-HS-PC1-12
Hard-Wire Pigtail
LV-HS-PC1-40
Bar to Bar Connector
Each LED Light Connect Light Bar includes:
-2 Mounting Clip
-Power Connector cable
XLD200B-224V-FC (24VDC)
1m (40”)
Only Connect identical
voltage LED bars!
Maximum Connect - 16 feet (5M) for 24VDC (288 LEDs)
Front Connector
LED Bar
2/2
For further Optional connectors and power supplies check our website
www.ledworldlighting.com
Powers up to 10 feet of LED
Connect Bar Lighting
Powers up to 16 feet of LED
Connect Bar Lighting
E96L24DC-KO Class 2
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.0-04/28/15
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Electronic Dimmable
1-800-387-4081
ledworldlighting.com ledworld.ca |