LED World T3-CV User manual
T3-CV Receiver Manual
T3-CV Operation Overview
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.2 11/16/2015
DC12V~24V
Remote ID
Learning Button
Power Input
RGB LED Connection Socket
MODEL : T3-CV
2.4G WIRELESS REMOTE CONTROL
POWER INPUT : DC5V-DC24V
MAX INPUT: 5A
Use only with Class 2 Power Source
Mounting point
Securely mount the T3-CV using the two mounting points at each end.
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with
the National Electric Code, and local regulations.
Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).
Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire,
factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire
installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near
water (or the possibility of in the future).
Do not modify this product beyond the instructions in this guide or the warranty will be voided.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before
proceeding with a qualied electrician familiar with low voltage wiring techniques.
Safety & Warnings
Before you begin, read all warnings and installation instructions (as they may have been updated from previous versions ).
Improper installation(s) present hazards, which can result in personal injury or property damage.
Diagram-1
Warning: Input voltage must be identical to output voltage of the LED Fixture!
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to
cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw
terminals. Use 22 to 16 AWG gauge wire for output terminals.
WIRE 6-8MM (0.25-0.30”)
Pairing and Unpairing T3-CV with Optional T3 Remote Control
Pairing :
On T3-CV press the learning button for about 3 seconds until buzzer sounds. On T3 Remote control press any key from
1-9 for about 5 seconds until you hear buzzer sound. Now T3-CV and T3 remote are connected.
Unpairing:
On T3-CV press the learning button until you hear second long buzzer sound . On T3 Remote control press any key
from 1-9 until you hear buzzer sound. Now T3-CV and T3 remote are disconnected.
1/2
1-800-387-4081
ledworldlighting.com ledworld.ca |
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
T3-CV Receiver Manual
1
Input voltage
Max current load
Max output power
Compatible remote control
Remote Distance
DC5V-DC24V
Class 2 (5A)
60W/100W (12V/24V)
T1/T2/T2M/T3/T3M/T3X
20m (65 Feet)
Working temperature
Dimension
-20°C~40°C
L175 × W44 × H30mm
T3-CV Technical Specications
Class 2 Low Voltage Regulated Driver
T3-CV - 12V Wire Diagram (uses MTR72DAUL-1250B power supply)
RGB LED Strip
T3-CV
MODEL : T3-CV
2.4G WIRELESS REMOTE CONTROL
POWER INPUT : DC5V-DC24V
OUTPUT : 6A x 3CH
Diagram-3
AC Power
50/60Hz
MTR72DAUL-1250B
or other
Class 2 drivers
H05 Connector cable
If used with MTR72DAUL-1250B
Power Supply
[+]
[B]
[G]
[R]
2/2
L
N
AC Power
50/60Hz
Class 2 Low Voltage Regulated Driver
(match Voltage with LED Strip Voltage)
G
N
L
t
up
n
I
t
u
p
t
u
O
V+
V-
T3-CV Hard Wire Diagram
RGB LED Strip
T3-CV
MODEL : T3-CV
2.4G WIRELESS REMOTE CONTROL
POWER INPUT : DC5V-DC24V
MAX INPUT: 5A
Use only with Class 2 Power Source
Diagram-2
[+]
[B]
[G]
[R]
Recommended 14~20 AWG cord
Recommended 14~20 AWG cord
+-
Make sure that
wires cannot
cross
+-
Make sure that
wires are screwed tight
and fully inserted
wrong correct
1-800-387-4081
ledworldlighting.com ledworld.ca |
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.2 11/16/2015
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including
interference that may cause undesired operation.
Note: The manufactures is not responsible for any radio or tv interference caused by unauthorized modications to
this equipment. Such modications could void the user's authority to operate the equipment.
(match Voltage with LED Strip Voltage)
Other LED World Receiver manuals
