Ledra Brands BRUCK Eco Track User manual

Ledra Brands Inc.
www.LedraBrands.com
In a continuing effort to offer the best product possible we reserve the right to change, without notice, specications or materials that in our opinion will not alter the function of the product.
15774 Gateway Circle Tustin, CA 92780
P 714.259.9959 F 714.259.9969
v.11.7.19
Eco Fixture Mounting
Installation Instructions
To avoid possible electrical shock, before installing light
xtures, disconnect power by turning off the circuit breakers
both to the outlet box and to its associated wall switch location
if you cannot lock the circuit breakers in the off position,
securely fasten a prominent warning device, such as a tag to
the service panel.
Verify that supply voltage is correct by comparing it with the
luminaire label information.
Make all electrical and grounded connections in the
accordance with the National Electrical Code (NEC) and any
applicable local code requirements.
Allow sufcient time for xture and / or driver to cool before
servicing and performing maintenance.
READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE INSTALLING OR MAINTAINING THIS PRODUCT.
TURN OFF POWER PRIOR TO ANY WORK ON THE TRACK, SYSTEM OR PRODUCT.
DO NOT INSTALL DAMAGED PRODUCT.
Installation, wiring, and maintenance must be done by a certied electrician in accordance with all local and National Electrical Codes.
Warranty is voided in case of unauthorized modications and/or improper use.
Save these instructions and refer to them when additions, changes, or services to the ECO xture or the ECO track system are made.
CAUTION – Do not install any xture assembly closer than 6 inches (15.24 cm) from any combustible material.
Do not install any part of an ECO track system less than 5 feet (1.542 m) above the oor.
Do not attempt to energize anything other than ECO track luminaires on track.
Suitable for dry locations only.
Para evitar un posible choque, antes de instalar luminarias,
desconecte la alimentación apagando los interruptores de
circuito y ubicación del interruptor de pared. Si no se pueden
bloquear los interruptores en la posición de apagado, sujetar
un dispositivo de advertencia en el panel de servicio.
Compruebe que la tensión de alimentación es correcta
comparándola con la información de etiqueta de la luminaria.
Hacer todas las conexiones eléctricas y puesta a tierra de
acuerdo con el código eléctrico nacional (NEC) y los requisitos
del código local aplicable.
Permitir suciente tiempo para el luminario y el controlador
para enfriar antes de enpesar el servicios y mantenimiento.
Pour éviter les chocs, avant d’installer des appareils
d’éclairage, coupez l’alimentation en désactivant les
disjoncteurs et l’emplacement du commutateur mural. Si vous
ne pouvez pas verrouiller les disjoncteurs en position d’arrêt,
xer un avertissement sur le panneau de service.
Vériez que la tension d’alimentation est correcte en le
comparant avec les informations d’étiquette de luminaire.
Effectuer tous les raccordements électriques et mise à la terre
dans la conformité avec le Code électrique National (NEC) et
des exigencies du code local applicable.
Laisser sufsamment de temps pour l’appareil et pilote
refroidir avant d’effectuer l’entretien et la maintenance.
All wiring must be in accordance with national and local
electrical codes and ANSI/NFPA 70. If you are unfamiliar with
wiring you should use qualied electrician.
PPE Personal Protective Equipment such as gloves and
safety glasses should be used at all times when installing,
maintaining or servicing.
Risk of re. Keep combustible material away from xtures.
Todo el cableado debe hacerse de conformidad con los
códigos eléctricos nacionales y locales y ANSI/NFPA 70. Si
no está familiarizado con el cableado, se debe utilizar a un
electricista.
Equipo de protección personal como guantes y lentes de
seguridad se debe utilizar al instalar, mantener o reparar.
Riesgo de incendio. Mantenga los materiales combustibles
lejos de los liminario.
Tout le câblage doit être effectué conformément aux codes
électriques locaux et nationaux et ANSI/NFPA 70. Si vous êtes
peu familier avec câblage, vous devez utiliser un électricien
qualié.
Équipement de protection personnelle comme des gants et
des lunettes de sécurité doivent être utilisé en tout temps lors
de l’installation, maintenance ou entretien.
Risque d’incendie. Garder les matières combustibles loin de
luminaires.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
WARNING
CAUTION
ADVERTENCIA
PRECAUCION
AVERTISSEMENT
MIS EN GARDE

v.11.7.19 Ledra Brands Inc.
www.LedraBrands.com
In a continuing effort to offer the best product possible we reserve the right to change, without notice, specications or materials that in our opinion will not alter the function of the product.
15774 Gateway Circle Tustin, CA 92780
P 714.259.9959 F 714.259.9969
INSTRUCTIONS FOR USE
REMOVAL
De-energize circuit before installation.
Depress Eco track adapter contact tabs to ensure electrical contact
tabs are fully seated on the ECO track adapter before inserting into
ECO track.
Align release tab to the groove (polarity) side of the ECO track.
While inserting the ECO adapter into the ECO track, twist the ECO
adapter counterclockwise 90 degrees. ECO adapter will snap into
the ECO track.
Polarity line on ECO adapter must align with polarity line on ECO track.
Energize circuit and test for proper operation.
Hold xture body.
Depress the release tab on the ECO adapter.
Rotate the ECO adapter clockwise 90 degrees, releasing it from the
ECO track.
Reposition or replace as required.
1
2
3
4
5
6
1
2
3
4
ensure tabs are
fully seated