LEGRAND Sanus WSS52 User manual

WSS 52
WIRELESS SPEAKER STAND
INSTRUCTION MANUAL
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call. We’re ready to help!
US: [phone] • UK: [phone] • EMEA: [phone]

2
This stand is designed to support the Sonos®PLAY:5™and Five™speaker only.
IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS
CAUTION: Avoid potential personal injuries and property damage!
•Check your speaker owner’s manual to see if there are any special requirements for mounting your speaker.
•Please read through these instructions completely to be sure you’re comfortable with this easy install process.
• Do not use this product for any purpose not explicitly specified by manufacturer.
• Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
• If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product,
contact Customer Service at: US: [phone] • UK: [phone] • EMEA: [phone].
Before getting started, let’s make sure this product is perfect for you!
15 lbs.
(6.8 kg)
Speaker Weight Limit
DO NOT EXCEED
Tool Needed Screwdriver

3
Dimensions
10.90
[276.9]
5.86
[148.8]
11.00
[279.4]
4.97
[126.1]
31.46
[799.1]
TOP VIEW
FRONT VIEW SIDE VIEW
3-D
31.46 in.
799.1 mm
6.24 in.
158.5 mm
6.75 in.
171.4 mm
7.76 in.
197.0 mm
6.1in.
155.0 mm
11.00 in.
279.4 mm
10.9 in.
276.9 mm

M6 x 20 mm
M6
M6 x 20mm
M5 x 14mm
1/4-20 x 1/2”
STEPS 1 & 2 STEP 3 STEP 5
STEP 7
STEP 4
4
Parts and Hardware
NOTE: Not all hardware included will be used.
OPTIONAL
Base
Shaft Screw
Lock Washer
Top Plate
M5 Screw
Carpet Spike
Jam Nut
Rubber Pad
Clip
Shaft
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service. Never use damaged parts!
x1
01
Front Horizontal
Bumper
Rear Bumpers
Front Bumper
Screws
Vertical Bracket
Horizontal Orientation Vertical Orientation
Front Vertical
Bumper
x1
02
x2
03
x2
04
x4
05
x4
06
x4
07
x1
08
x1
09
x1
10
x2
11
x1
12
x1
13
x2
14
x2
15

Route Power Cables STEP 1
Ethernet
(if needed)
02
5
Attach Base to Shaft STEP 2
01
02
03 04

6
Optional Carpet Spikes
Rubber Pads
Install Rubber Pads -or- Carpet Spikes STEP 3
Twist rubber pads 05 into the base 02 .
WARNING:
The ends of carpet
spikes 06 are
sharp and may
scratch flooring,
damage wiring, or
be hazardous to
children.
02
02
05
OR
07 06
===
HEIGHT ADJUST
07
06

7
Attach Top Plate to Shaft STEP 4
M5 x 14mm
09
08
01

8
Determine Speaker Orientation STEP 5
Vertical Orientation
Horizontal Orientation
OR
Go to STEP 5A on
PAGE 9
Go to STEP 5B
on PAGE 10

9
Horizontal Orientation 5A
1 Install Front Bumper 2 Install Rear Bumpers
1/4-20 x 1/2”
14
08
10 11
0801 01

10
Vertical Orientation 5B
1 Install Front Bumper 2 Slide Rear Bracket onto Rear Tabs
1/4-20 x 1/2”
14
08
12
01
13
01
08