LEGRAND SANUS ACCENTS ALT2 User manual

ALT
2
INSTRUCTION MANUAL
BEFORE YOU BEGIN
Remove the
stand
from your TV —
if attached.
Install any accessories
you may have purchased, if they
requireTV removal prior to assembly.
Note that the TV is removable for
future accessory purchases.
Protect the face
of your TV when
laying it down for
installation.
Para Español ver página 12
Our US-based
install experts
are standing
by to help.
Call us at:
[phone]
Get it right the
first time.
HeightFinder™
shows you
where to drill.
Check it out at:
SANUS.com/1170
Want to watch a
video that shows
how easy this DIY
project will be?
Watch it now at:
SAN.US/3090
WE’RE HERE TO HELP
Or, chat at:
SANUS.com/chatSA

2
IMPORTANT SAFETY INSTRUCTIONS
– PLEASE READ MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed ONLY to be installed into wood studs, solid concrete* or concrete block*, and steel studs*,
—DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV.
*For information on how to use this product with concrete or steel stud walls contact Customer Service and ask about the mounting kit.
●This product is designed for INDOOR USE ONLY
●The wall must be capable of supporting five times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
TV Weight Limit
(including accessories)
DO NOT EXCEED
Tools Needed
Wall
Construction
ONLY install on these
acceptable wall types.
Pencil Level Tape Screwdriver
Tape Measure Electric Drill Socket Wrench
Call Customer Service
Unsure
If your TV (plus accessories) weighs MORE,
this mount is NOT compatible.
Visit Accents.SANUS.com or call customer
service to find a compatible mount.
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service.
110 lb
(49.8 kg)
Wood Stud Install
Steel Stud Install
Concrete Install
Awl Awl
Stud
Finder Stud Finder
7/32 in.
(5.5 mm)
Wood
1/2 in.
(13 mm)
Steel
Drill Bit Drill BitHammerDrill Bit
3/8 in.
(10 mm)
Concrete
1/2 in.
(13 mm)
Drywall alone will NOT hold
the weight of your TV
CAUTION:
DO NOT
install in
drywall alone
steel studs
wood studs Solid concrete
or concrete
block
ACCEPTABLE
Steel stud kit #SSMK1 is
required [NOT INCLUDED]
Call Customer Service
Concrete kit #CMK1 is
required [NOT INCLUDED]
Call Customer Service
ACCEPTABLEACCEPTABLE

3
Dimensions
23.6in
600mm
MAX VESA
15.7in
400mm
MAX VESA
3.9in
100mm
MIN VESA
3.9in
100mm
MIN VESA
28.4in
721mm
19.3in
489mm
23.9in
607.6mm
4.0in
100.5mm
12.8in
323.9mm
25.4in
645.2mm
16.5in
419.1mm
30.0in
761mm
6.0in
153mm
2.8in
70mm
8deg 12deg
5.1in
128mm
3.9in
100mm
22.1in
562mm
3.9in
100mm
TV INTERFACE
WALL PLATE
TOP VIEW - EXTENDED
3-D
SIDE VIEW - EXTENDED
SIDE VIEW RETRACTED FRONT VIEW - RETRACTED
FULLY ASSEMBLED MOUNT
NOTE: During operation, your TV shifts
2.28 in. (58 mm) when retracted or extended.
To help fine-tune the placement of your TV,
the wall plate includes slotted holes and the
TV brackets
can be located
anywhere
along the
wall plate. EXTENDED
RETRACTED
2.28 in. (58 mm)
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts
are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
Supplied Parts and Hardware
5/16 x 2¾in.
5/16 in.
10-32 x 1¼in.
2.5mm
22mm
5mm
M8 x 20mm
M6 x 20mmM6 x 12mm
M4 x 12mm
M6 x 35mm
M4 x 35mm
M8 x 16mm M8x30 mm
M8 x 40mm M8 x 50mm
Parts and Hardware for STEP 1
TV Brackets
TV Screws
(qty. 4 each)
[Only one size fits your TV]
Washers
(qty. 4 each) Spacers
(qty. 4 each)
[If necessary]
03
02
01
M4 M4
M6/M8
M6
M8
CAUTION: Avoid potential
personal injury or property damage!
The TV brackets
contain potential
pinch points during
operation.
Keep fingers away
from pinch points
when retracting the
TV. (arrows)
(qty. 1)
04
(qty. 1)
05
NOTE: Not all hardware included will be used.
NOTE: Illustrations may vary slightly from your actual parts.

4
Parts and Hardware for STEP 2
Hardware for STEP 3
5/16 x 2¾in.
5/16 in.
10-32 x 1¼in.
2.5mm
22mm
5mm
M8 x 20mm
M6 x 20mmM6 x 12mm
M4 x 12mm
M6 x 35mm
M4 x 35mm
M8 x 16mm M8x30 mm
M8 x 40mm M8 x 50mm
Wall Plate Template
Wall Plate
Lag Bolts
Lag Bolt Washer
Locking Screw
06 (qty. 1)
07 (qty. 1)
08 (qty. 4)
09 (qty. 4)
10 (qty. 2)
1/4-20 x 1¾ in.
1/4-20 SnapToggle BB
1/4 in.
5/16 x 2¾ in.
5/16 in.
Fischer UX10 x 60R
Concrete Anchors
For concrete installations ONLY
CAUTION: Do not use in drywall or wood
Lag Bolts
Washer
Hardware for STEP 2B
Concrete Installation
[Concrete Kit #CMK1 is NOT INCLUDED]
Hardware for STEP 2C
Steel Stud Installation
[Steel Stud Kit #SSMK1 is NOT INCLUDED]
Contact Customer Service at [phone]
and ask about the SSMK1 Steel Stud Anchor Kit.
Contact Customer Service at [phone]
and ask about the CMK1 Concrete Anchor Kit.
Anchor
Washer
Screw
C2 (qty. 4)
C3 (qty. 4)
C1
(qty. 4)
S1 (qty. 4)
S2 (qty. 4)
S3 (qty. 4)

5
STEP 1 Attach TV Bracket to TV
1.3 Attach TV Brackets to Your TV
Inset Holes Cables Rounded Back
1.2 Select TV Screw Length and Spacers
• Flat Back TV
[TV brackets
lay flat on your TV]
NO SPACER SPACER NEEDED
• Flat Back TV with
Extra Space Needed
[for deep inset holes
or cable interference]
• Rounded or
Irregular Back TV
[TV brackets NOT
resting flat on your TV]
A B
Use short TV screws 01 .
Spacers 03 not needed.
Use long TV screws 01 and spacers 03 to
create extra space between the TV and TV bracket.
1.1 Select TV Screw Diameter
Only one screw size fits your TV.
M4 M6 M8
01
CAUTION: Verify adequate thread engagement with your screw 01 ,
washer 02 , spacer 03 combination AND TV bracket 04 / 05 .
— Too short will not hold your TV. — Too long will damage your TV.
NOTE: If your TV
included inset spacers
or adapters, use them
UNDER the mount
hardware.
NO SPACER SPACER NEEDED
Position the TV brackets 04 and 05 over your TV hole pattern as
shown - making sure the brackets are level.
IMPORTANT:The tilt tension knobs Tshould be oriented to
the outside edges.
Install using the screw combination Aor Byou selected for your TV.
CAUTION: Avoid potential personal injuries and property damage!
DO NOT use power tools for this step. Tighten the screws only enough
to secure the TV bracket to the TV. DO NOT overtighten the screws.
12
AB
TOP OF TV
TT
0202 01 01
03
04 05

6
CAUTION: Avoid potential personal injury or property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1½ x 3½ in. (38 x 89 mm)
●Minimum horizontal space between fasteners: 16 in. ( 406 mm)
●Stud center must be verified
IMPORTANT: Drill into the center of the stud.
Go to STEP 3 on PAGE 9.
STEP 2A Attach Wall Plate Wood Stud Installation
12
Min.
16 in.
(406 mm)
EXTENDED
2.28 in. (58 mm)
RETRACTED
NOTE: During operation, your TV
shifts 2.28 in. (58 mm) when retracted
or extended. The wall plate and TV
brackets have built-in adjustments to
help fine-tune your TV placement.
06
Max.
5/8 in.
(16 mm)
3 4
2 ¾in. (70 mm)
7/32 in.
(5.5 mm) 08
09
07
06
Install the wall plate 07 using four lag bolts 08 and washers 09 .
TIP: Use the slotted holes for fine-tuning your placement.
Tighten all lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the
lag bolt. DO NOT over-tighten the lag bolts.

7
CAUTION: Avoid potential personal injury or property damage!
●Mount wall plate 07 directly onto concrete surface (no wall covering)
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
●Minimum horizontal space between fasteners: 16 in. (406 mm)
CAUTION: Be sure the anchors C1
are seated flush with the concrete surface.
CAUTION: Never drill into the mortar between blocks.
Solid Concrete or Concrete Block Installation
STEP 2B Attach Wall Plate
Concrete Install Kit #CMK1 is not included
(see page 4) Contact Customer Service
at [phone] to inquire about the
additional hardware.
1 2
3/8 in.
(10 mm)
3 in. (75 mm)
EXTENDED
2.28 in. (58 mm)
RETRACTED
NOTE: During operation, your TV
shifts 2.28 in. (58 mm) when retracted
or extended. The wall plate and TV
brackets have built-in adjustments to
help fine-tune your TV placement.
002862.eps
Min. 16 in. (406 mm)
06
06
3 4
C1
C3 C2
07
Install the wall plate 07 using four lag bolts C3 and washers C2 .
TIP: Use the slotted holes for fine-tuning your placement.
Tighten all lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the
lag bolt. DO NOT over-tighten the lag bolts C3 .
Go to STEP 3 on PAGE 9.

8
3
S1 S1
S1
P
S1
CAUTION: Be sure cap Pis seated against the drywall surface.
4
07
S1
S2
S3
Steel Stud Installation
STEP 2C Attach Wall Plate
ab
cd
CAUTION: Avoid potential personal injury or property damage!
●Studs must be at least 2x4 in. / 25 ga.
●If back side of wall is unfinished, drywall must be installed to a minimum of one stud left and right of the stud(s) being used to install the mount
●Drywall must be a minimum of 1/2 in. (13 mm) thick on each side of the studs, and a minimum clearance of 1 ⅞in. (48 mm) behind the wall is required
●Pilot holes MUST be drilled to a depth of 1 in. (25 mm), using a 1/2 in. (13 mm.) diameter drill bit
●This product must be centered on the studs
●Stud type and structural strength must conform to the North American Specification for the Design of Cold-Formed Steel Structural Members [362 S 125 18, C-Shape, S - Stud Section]
●Drywall must be secured to studs with screws 12 in. (304.8 mm) on center
2
1 in. (25 mm)
1/2 in.
(13 mm)
1
06
Min.
16 in. (406 mm)
EXTENDED
2.28 in. (58 mm)
RETRACTED
NOTE: During operation, your TV
shifts 2.28 in. (58 mm) when retracted
or extended. The wall plate and TV
brackets have built-in adjustments to
help fine-tune your TV placement.
06
Install the wall plate 07 using four screws S3 and washers S2 .
TIP: Use the slotted holes for fine-tuning your placement.
Tighten all screws S3 only until they are pulled firmly against the
wall plate 07 .
CAUTION: Improper use could reduce the holding power of the
screws S3 . DO NOT over-tighten the screws S3 .

9
STEP 3 Hang TV onto Wall Plate
1
CAUTION: Avoid potential personal injury!
TV brackets 04 and 05 contain potential pinch
points during operation. Keep fingers away from
pinch points when retracting the TV. (arrows)
2
NOTE: The TV brackets (TV)
can be positioned anywhere
along the wall plate to counteract
the 2.28 in. (58 mm) offset during
TV operation (extend/retract).
See PAGE 3 for offset details.
HEAVY! You may need assistance with this step.
Extend the TV brackets 04 and 05 as shown Align the ends of TV brackets 04 and 05 with your TV.
0405
0405
4
IMPORTANT: BEFORE MOVING YOUR TV, SECURELY
tighten down screws 10 to properly install the assembly.
3
07
07
10
Rest the TV (brackets 04 and 05 ) against the wall plate 07 .
Install locking screws 10 to secure TV to wall plate 07 .
CAUTION: Avoid potential personal injuries or property damage!
Screws 10 must be installed to secure arms to wall plate 07 .
Periodic tightening may be required.
04 05
04
05
07
0504
Determine where on the wallplate you want to position your TV.
Hang your TV by fitting the hooks of BOTH TV brackets 04 and 05
over the top edge of the wall plate 07 .
IMPORTANT: Ensure BOTH TV brackets are connected.

10
TILT ADJUSTMENT
TV Adjustments
Manage Cables
EXTEND / RETRACT -- ONLY IF NECESSARY
Move your TV to various positions,
as needed to attach your cables,
then adjust the TV as desired.
CAUTION:
Avoid potential personal injury!
The TV brackets contain potential
pinch points during operation.
Keep fingers away from pinch points
when retracting the TV. (see arrows)
If your TV doesn't extend or retract properly,
remove your TV (See PAGE 11, then reinstall
following STEP 3 on PAGE 9.
IMPORTANT: BEFORE MOVING
YOUR TV, securely tighten down screws
10 shown on PAGE 9, STEP 3, to
properly install the assembly.
T
0504
Your TV should adjust easily when moved, then stay
in place. If your TV is too loose or too tight, adjust side
tension knobs T.
NOTE: Once your TV is in place, tighten the side
tension knobs Tto prevent unwanted movement.