LEGRAND 6338 45 User manual

Outdoor Speakers
6338 45
LE00371AA
Description
The 6338 45 Outdoor Speaker is made of a tough semi-flexible plastic and also features a perforated
aluminum grill. The brackets are powder coated aluminum.
A. For pre-wire, run x/2 conductor (x=gauge) stranded speaker wire from the distribution/volume control to
each outdoor speaker location.
B. Drill a hole large enough to accommodate the speaker wire through the outside wall at an appropriate
location for each outdoor speaker, and place each speaker wire from the volume control through the hole to
the outside.
Leave at least a foot of wire outside, and seal the hole with caulk.
C. Place the speaker wire through the hole in the center of the Outdoor Speaker bracket, and mount the
Speaker brackets to the outside wall using two screws per bracket (see Figure 3), and the appropriate
retention device (i.e. masonry inserts for a masonry wall).
Installation
NOTE: It is recommended that a minimum of 16 gauge, 2 conductor wire be used for most
applications from the amplifier or volume control to the speaker. Different gauges can, and should,
be used based upon the distance of the intended run or quality of installation (see Figure 2)
Figure 2
Figure 1
Figure 3
Distance Gauge
< 10 Feet
10-50 Feet
> 50 Feet
18
16
14
D. Strip off 60 mm or so of the speaker cable jacket to expose the positive and negative insulated wires.
Strip 10 mm of insulation off of these conductors.
E. Hold the speaker with one hand, (if speaker grill is off, pay careful attention not to push on the woofer’s
cone, this can cause permanent contortion of the voice coil, thus producing a mechanical rubbing sound or
speaker failure) unscrew the Red and Black screw terminals, insert the bare speaker wires through the hole
in each post, and tighten each screw terminal. Be sure to have the positive wire in the RED terminal and
the negative in the BLACK (see Figure 4). As you tighten each screw terminal wiggle the wire and
tighten some more.

Safety instructions
This product should be installed preferably by a qualified electrician.
Incorrect installation and use can entail risk of electric shock or fire. Before carrying out the installation,
read the instructions and take account of the product’s specific mounting location. Do not open up the
device.
All Legrand products must be exclusively opened and repaired by personnel trained and approved by
LEGRAND. Any unauthorised opening or repair completely cancels all liabilities and the rights to
replacement and guarantees. Only use genuine accessories.
NOTE: Wiring both speakers identically as the above instruction states will yield speakers that are
“in phase”. If one speaker is wired opposite of the other, the speakers will be “out of phase”
with one another. If the speakers are “out of phase” the sound might appear smeared (canned) and
a significant loss of bass might be noticeable due to phase cancellation. Make sure every installed
speaker is correctly phased.
Figure 4
F. Once the speakers are wired correctly, attach them to the bracket with the large round retainers provided
with the speakers (see Figure 5). The retainers allow the speakers to be rotated in the bracket to direct the
sound output.
Figure 5
8î Speaker (2.1 CuFt) BlockingDistance
16” on Center, 2x4 71.50”
16” on Center, 2x6
16” on Center, 2x8
16” on Center, 2x10
16” on Center, 2x12
24” on Center, 2x4
24” on Center, 2x6
45.50”
34.50”
27.00”
22.25”
46.00”
29.50”
6.5”Speaker (0.7 CuFt) BlockingDistance
16” on Center, 2x4 24.00”
16” on Center, 2x6
16” on Center, 2x8
16” on Center, 2x10
16” on Center, 2x12
24” on Center, 2x4
24” on Center, 2x6
15.25”
11.50”
9.00”
7.50”
15.50”
10.00”