LEGRAND Vaddio 999-85600-000 Instruction Manual

Document Number 411-0050-31 Rev A – December 2020
Installing the Vaddio Ceiling-Mounted Speaker
This guide contains information on installing the Vaddio Ceiling-Mounted Speaker, a
2-way enclosed speaker designed by Vaddio.
Features
nHigh-performance metalized polypropylene cone woofer with doubled
neodymium magnet assembly for increased efficiency
nButyl rubber woofer driver surround for longevity
nCoaxially located damped poly cone tweeter, rigidly affixed to woofer magnet structure
nCeiling or wall installation
nRemovable Phoenix-style signal connection plug
nConvenient swivel-out mounting tabs
nRecessed cable cavity with pivoting cover and wiring clamp
nLightweight aluminum tile brace for US (24 in.) or Euro style (60 cm) ceiling tiles
nTile brace includes corner holes for additional safety wires or leveling hangers
nTexture painted steel enclosure with safety loop
n27 in. (68.6 cm) stainless steel safety cable with steel carabiner clips
nWhite painted metal grille with easy magnetic installation
Specifications
Power 40 W Body Diameter 7.2 in. (182.9 mm)
Characteristic Impedance 8 ohms Height 6 in. (152.4 mm)
Installed Weight 6.4 lb. (2.9 kg) Grille Diameter 8.6 in. (218.4 mm)
What's in the Box
Make sure you received all the items you expected.
Vaddio Ceiling-Mounted Speaker (worldwide) – 999-85600-000
nVaddio Ceiling-Mounted Speaker with detachable grille, qty. 2
nEuro-style 4-pin audio connector, qty. 2
nTile brace, qty. 2
n27 in. (68.6 cm) stainless steel safety cable with steel carabiner clips, qty. 2
nInstallation Guide
Contact Vaddio Technical Support if you did not receive all the items listed.
Find full product documentation on the applicable product page(s) at legrandav.com.
Preparing for a Successful Audio Installation
Tips for avoiding common audio problems:
nTo prevent audio feedback, ensure that speakers are more than 4 ft. (1.2 m) from any microphone. More
separation is better.
nRange is comparable to Vaddio ceiling microphones. Two speakers provide good coverage for a small
conference room; larger spaces may require more speakers.

Tools You Will Need
To install the speaker, you will need:
nHole saw for the appropriate type of ceiling
n#2 Phillips screwdriver
nWire cutters
nTape measure
nLadder or lift
nAppropriate personal protective equipment
We recommend Chief’s “Speed Connect Hardware Kit,” part number CMSHDW, to suspend the included
tile brace with safety wires.
Don’t Void Your Warranty!
Caution
This product is for indoor use. Do not install it outdoors or in a humid environment without the appropriate
protective enclosure. Do not allow it to come into contact with any liquid.
Do not install or operate this product if it has been dropped, damaged, or exposed to liquids. If any of these
things happen, return it to Vaddio for safety and functional testing.
Basic Connections
Connect the speaker(s) to the room system through an amplifier, such as the Vaddio EasyUSB
Mixer/Amp.
Installing Vaddio Ceiling-Mounted Speakers
2

Preparing the Ceiling
Warning
Follow standard safety practices when using ladders or lifts. Failure to do so can result in injury or death.
We like you, we don't want you to be injured or killed, and we hope you understand the gravity of the
situation.
Note
All above-ceiling work must conform to local building codes and should be performed by qualified
personnel.
If installing in a hard ceiling:
Using the tile brace as a template, make a hole in the ceiling where the speaker will be mounted.
If installing in a suspended tile ceiling:
1. Remove the ceiling tile where the microphone will be mounted, and make a hole in the ceiling tile using
the tile brace as a template.
2. Reinstall the ceiling tile and position the tile brace.
3. Optional but recommended: Secure the tile support brace to the building structure using appropriate
hardware such as Chief’s “Speed Connect Hardware Kit,” part number CMSHDW. The ends of the tile
brace have holes to accommodate support wires.
Installing the Speaker
1. Remove the magnetically attached speaker grille.
2. Guide the speaker up through the hole in the ceiling.
3. Turn each of the four Phillips screws in the front face of the speaker a quarter-turn to rotate the mounting
tabs into place, securing the speaker.
4. Put the speaker grille back in place.
Installing Vaddio Ceiling-Mounted Speakers
3

Installing Vaddio Ceiling-Mounted Speakers
Connecting the Cable
1. Attach the 27-in. (68.6 cm) safety wire to the safety loop on the back of the speaker and to a suitable
anchor point.
2. Loosen the screw holding the connector cover in place, and pivot the cover outward.
3. Loosen the screw securing each side of the cable clamp to the speaker body, and loosen the two long
clamp adjustment screws.
4. Route the speaker cable through the cable clamp and connect it.
5. Tighten the clamp adjustment screws until the cable is held securely in the clamp. Then tighten the
screws securing the clamp to the speaker body.
6. Move the connector cover back into place and tighten the screw.
Vaddio is a brand of Legrand AV Inc. · www.legrandav.com · Phone [phone] · Fax
+1.763.971.4464 · Email [e-mail]
Visit us at www.legrandav.com for firmware updates, specifications, drawings, manuals, technical support
information, and more.
©2020 Legrand AV Inc.
Vaddio is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification
purposes and are trademarks of their respective owners. All patents are protected under existing
designations. Other patents pending.
Commercial AV Brands Chief | Da-Lite | Middle Atlantic | Projecta | Vaddio