LEHA Luxaflex PowerView Gen 3 User manual

The PowerView® Gen 3 Remote has
been redesigned with a modern look
while maintaining its compatibility
with the PowerView® Pebble® and
Surface. Precisely control your Gen 3
shades throughout your home with
the touch of a button. The following
pages provide all the details on how
to set up and operate both remote
versions.
Table of Contents
Key Components ...................................... 1
Getting Started.......................................... 2
Programming ............................................ 3
Basic Operation ......................................... 4
Battery Replacement ................................ 5
Troubleshooting........................................ 6
Key Components
GEN 3 REMOTE MODULE
BATTERIES INCLUDED
WITH REMOTE
1
OR
PowerView
®
Automation Gen 3
REMOTE CONTROL GUIDE
PEBBLE®
SURROUND
WALL SURFACE
SURROUND

Getting Started
2
IMPORTANT: The PowerView® Gen 3 Remote
will not operate a shade until the shade and
remote have been added and configured to a
Home in the PowerView® App.
GETTING STARTED: First, activate the remote
by pulling both plastic tabs from the back battery
compartment.
NOTE:If placing the remote module into a
Pewter or Clear Frost Pebble®, ensure the provided
colour insert is seated at the bottom of the
Pebble® cutout.
Inserting the remote module into the
PowerView® Pebble® (hand-held):
1. Centre the Luxaflex®logo on the remote
module above the indentation on the
bottom rim of the Pebble®.
2. Align the ribs on the remote module
with the grooves on the Pebble®.
3. Gently push the remote module into
the Pebble® until it fits smoothly.
Ribs on remote to be
aligned with the
grooves on the Pebble®.
CENTRE LOGO
Mounting the PowerView® Surface:
1. Choose a location to mount
the Surface.
2. Orient the Surface mounting plate so
that the Luxaflex® logo is horizontal and
height. Mark screw holes.
3. Mounting the Surface onto drywall?
Use a 7
⁄32" drill bit to drill pilot holes. Tap
drywall anchors into the pilot holes until
the flange of the anchor is flush with
the drywall.
Mounting the Surface onto wood? Use
a 3⁄32" drill bit to drill screw holes.
Ribs on remote to be
aligned with the
grooves on the Surface.
CENTRE LOGO
4. Attach the Surface mounting plate
using the screws provided.
5. Align the Surface ring with its
mounting plate. Twist the Surface ring
clockwise to lock it in place.
Inserting the remote module in the Surface:
1. Align the ribs on the remote module with
the grooves on the Surface.
2. Gently push the remote module
into the Surface until it is snug.

Programming
3
IMPORTANT: All remotes (independent of how
many are in a project) are programmed solely
through the PowerView® App.
Download the PowerView® App from
the Apple or Google Play store or scan this QR
code.
HOW TO CONFIGURE A REMOTE
NOTE:A single shade or multiple shades can be
added to a single GROUP. Additionally, a single
shade can be assigned to more than one GROUP.
We recommend only similar shades be included
in a GROUP because of differences in product
features and operation.
DEACTIVATING THE REMOTE’S
“RAISE-TO-WAKE” FEATURE
The remote’s LEDs will automatically turn
on whenever the remote is picked up. This
feature is useful for immediately seeing which
shade GROUP buttons were activated last.
Deactivating this feature will help conserve
battery life.
To deactivate, press and hold the GROUP 6
button on the remote for 5 seconds, or until
LEDs start flashing. To activate the LED again,
follow the same steps. Press and hold the
GROUP 6 button for 5 seconds, or until LEDs
start flashing.
Please note, regardless if the “Raise-
to-Wake” feature is on or off, the
remote’s LEDs will turn on when any
button is pressed.
REMOVING A SHADE FROM A GROUP
1. Open the PowerView® App and
navigate to “More” 
“Accessories” “Remotes”.
2. Select the desired remote.
3. In the virtual remote configuration page,
select the GROUP that you want to
remove a shade from.
4. Select the editing tool button in the bot-
tom right-hand corner of the screen.
5. Select the shade you want removed
from the GROUP. The orange circle with
the checkmark should disappear to
confirm which shades are assigned to
that GROUP. Then select “Done”.
6. Select “Sync” and follow the prompts
to sync your remote to complete the
removal process.
SETTING FAVOURITE POSITIONS
Each Gen 3 shade has two FAVOURITE
positions. Each shade has two default
FAVOURITE positions based on the shade
type.
To set a new FAVOURITE position:
1. Open the PowerView® App and
navigate to “More” “Shades” 
Select the specific shade.
2. In the Shade Settings page, you will
see both FAVOURITE settings. Select
which position you want to modify.
3. Adjust the shade to the new desired
position and select “Done”. The new
FAVOURITE position is now saved.
Remotes can be set up in one or two ways:
1. During the initial Home setup process
2. After the Home is created by navigating
to “More” “Accessories” “Remotes”
The PowerView® App will guide you through the
entire process, from configuration to syncing
your remotes. Please follow each step carefully
in the app to successfully set up all remotes.
PowerView®

Basic Operation Once the shades have been joined to a GROUP
or multiple GROUPS, the remote is ready to
operate. Multiple shades can be operated at
the same time.
NOTE: Some PowerView® Gen 3 shades offer
variable operation from the basic operation
listed here.
BASIC OPERATION
1. To wake up the remote, simply pick it
up or press STOP. The last GROUPS)
selected will be highlighted and active.
2. Press ALL or GROUP 1– 6 button(s)
to select specific shade(s) to operate.
Selected GROUP button(s) will light to
show they are selected.
a. Multiple GROUP buttons may
be selected at the same time.
b. To deselect a GROUP, press the
GROUP button again. The backlit
GROUP button will go out.
3. Press OPEN to open the
selected shade(s).
4. Press CLOSE to close the
selected shade(s).
5. For shade(s) with vanes, louvers, slats, or
a middle rail*, press the RIGHT ARROW
to close the shade and open the vanes,
rotate the vanes to the right, tilt the
louvers/slats up or fully raise the middle
rail.
6. For shade(s) with vanes, louvers, slats, or
a middle rail*, press the LEFT ARROW
to close the vanes, rotate the vanes to
the left, tilt the louvers/slats down or
fully lower the middle rail.
NOTE: Single-function shades will
not operate by pressing the ARROW
buttons.
7. Press STOP to stop shade/vane/
louver/slat movement anywhere along
its travel.
8. While a shade is in motion, press the
opposite of its motion ( OPEN or
CLOSE) to reverse direction.
9. Press ♥ FAVOURITE to send select-
ed shade(s) to your first FAVOURITE
position. Double click FAVOURITE to
send selected shade(s) to your second
FAVOURITE position.
OPEN
CLOSE
LEFT ARROW
Function varies
by product type
RIGHT ARROW
Function varies
by product type
STOP
Stops shade motion
GROUP NUMBERS
Each number represents
a different group
FAVOURITE
• Click once to send shade(s) to your first
FAVOURITE position*
• Double click to send shade(s) to your second
FAVOURITE position**
* The default favourite positions vary based on the
shade type.
** Both favourite positions can be updated in the PowerView® App
under Shade Settings.
NOTE: Additional functions vary by
product type. To view your shade’s specific
functions, please consult your “Installation,
Operation and Care” manual.
4

Battery Replacement
5
REPLACING BATTERIES
IN THE REMOTE
Replacing the batteries in the remote module
will not cause the loss of any shade program-
ming, including GROUPS and FAVOURITES. The
remote uses two CR 2032 batteries.
1. For the PowerView® Gen 3 Remote with
Pebble®, slide your thumb in the inden-
tation, gently lift and remove the re-
mote module from the Pebble®. For the
PowerView® Gen 3 Remote with Surface,
remove the Surface from its mounting
plate by twisting the Surface count-
er-clockwise. Push the remote module
out from the back of the Surface.
2. Using a flat-head screwdriver, rotate
the safety screw counter-clockwise two
times.
3. Remove the back cover from the
remote.
4. Using a finger or small screwdriver,
gently lift and remove the old batteries.
5. Insert new batteries in their correct
orientation, making sure each is snug.
6. Align and replace the back cover onto
the backside of the remote module.
7. Using the flat-head screwdriver, rotate
the screw clockwise two times or until
the screw is snug.
8. Align the ribs on the remote module
with the grooves on the Pebble® or the
Surface.
9. Gently push the remote module into
the Pebble® or the Surface until it fits
smoothly.

Troubleshooting
6
1. None of the backlit buttons illuminate
on my remote when I press the buttons.
• Check to make sure the batteries
are inserted properly and are new.
• If the batteries are inserted properly
and the lights still do not turn on, the
batteries are likely dead and need to be
replaced. Refer to “Battery Replacement”
on page 5.
2. The shade is not responding to the
PowerView® Gen 3 remote.
• NOTE: A shade will not operate until it
is joined to a GROUP.
• Check that the correct GROUP number
is selected. The LED on that GROUP
number will light up. You can also
check which GROUP number the
shade is joined to on the remote in the
PowerView® App. You can find this under
“More” “Accessories” “Remotes.”
3. My shade operates when I press OPEN or
CLOSE, but not when I press either of the
arrow buttons.
• The arrow buttons are for operating
specific product lines. To see if your
shade has operational capabilities with
the arrow buttons, please refer to your
product’s “Installation, Operation and
Care” instructions.
• If your shade has operational capabilities
with the arrow buttons, calibrate it using
the PowerView® App. Select “More” 
“Shades” Select the affected shade 
“Advanced Options” “Calibrate Shade.”
The shade will then run a calibration
sequence. After the shade has finished
calibrating, try operating the shade again
with the arrow buttons on the remote.
4. How do I reset the remote?
• There is no resetting Gen 3 remotes. All
remote configuration (adding, modifying
and deleting remotes) is done through
the PowerView® App. Select“More” 
”Accessories” “Remotes”to configure
remotes.
5. The lights on my remote are red.
What does this mean?
• The batteries are getting low and need
to be replaced.