Lennox Hearth Products CANYON ST310 User manual

INSTALLATION AND OPERATION MANUAL
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
Save These Instructions
For Future Reference
Wood Stoves
Model Canyon™ ST310
Free-Standing
EPA Certied
Wood-Burning Stoves
P/N 775,217M, Rev. C, 05/2008
A French manual is available upon request. Order P/N 775,217CF.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la
pièce 775,217CF.
These appliances must be properly installed and operated in order to prevent the
possibility of a house re. Please read this entire installation and operation
manual before installing and using your wood stove. Failure to follow
these instructions could result in property damage, bodily injury or
even death. Contact your local building or re ofcials to obtain
a permit and information on any installation requirements
and inspection requirements in your area.
DRAFT
5/07/2008
US
Report # 050-S-09b-2

2
Move Cautions to Page 2 to be consistant with our other manuals (done 8-9-07)
General Safety Precautions
1. If this solid-fuel room heater is not properly installed, a house
fire may result. For your safety, follow the installation direc-
tions. Contact local building or fire officials about restrictions
and installation inspection requirements in your area.
2. Wear gloves during installation to avoid injury from sharp
edges on the stove and/or its parts.
3. This unit is designed and engineered to burn only dry, well-
seasoned wood. Burning wet wood will greatly reduce your
stoves efficiency, produce excessive amounts of smoke and
can cause dangerous chimney fires due to creosote build-
up.
4. Before opening the door, the draft control must be fully open
to avoid possible combustion flash (ignition of hot volatile
gases as the door is opened).
5. Do not use gasoline, gasoline-type lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start or “freshen up”
a fire in this stove. Keep all flammable liquids and combustible
materials 36” from any point of the stove when it is in use.
6. While burning, fuel utilizes oxygen from the air in the room.
Be sure to allow an adequate amount of fresh air into the
room where the stove is burning.
7. The outside surface of the stove will be hot while burning
properly and can set items like clothing and curtains on fire.
Keep furnishings and other combustible materials away from
the stove. Using the heat from the stove to dry wet clothing
can be hazardous if clothes are placed too near the surface
of the stove.
8. Hot while in operation. Keep children, clothing furnishings
and combustible material a considerable distance away.
Contact may cause skin burns. Do not allow children to play
near the stove without closesupervision.Donottouchthestove
while it is burning. Use extreme caution while the unit is in use.
Surface temperatures become dangerously hot and can cause
serious burns.
9. Do not allow anyone to operate the stove who is not familiar
with the operating instructions.
10. Attemptstoachieve heatoutput ratesthat exceedstove design
specifications can result in permanent damage to the stove.
Never leave your stove unattended on high burn rates. This
may cause overfiring. Overfiring the stove may cause a house
fire. If the stove glows, you are overfiring.
11. Keep a water hose or hand-operated fire extinguisher close
for safety.
12. Smoke Detectors - Since there are always several potential
sources of fire in any home, we recommend installing smoke
detectors. If possible, install the smoke detector in a hallway
adjacent to the room (to reduce the possibility of occasional
false activation from the heat produced by the stove). If your
local code requires a smoke detector be installed within the
same room, you must follow the requirements of your local
code. Check with your local building department for require-
ments in your area.
13. Inspect your chimney at least once a month during the burn-
ing season to check for soot and creosote accumulations.
Any accumulations over 1/4” thick should be removed by a
professional chimneysweep.Donotattemptto burnoutheavy
creosote accumulations with a hot fire. If large accumulations
are occurring, review your burning procedures.
14. If a creosote fire should develop, the fire department should
be called immediately and then attempts should be made to
control the fire until assistance arrives. If a “runaway” fire
should develop causing over-heating of the stove, the door
and draft regulators should be closed immediately. The fire
should die down once deprived of oxygen. After a severe
chimney fire,thecomplete chimney systemshould bechecked
before further use.
15. Do not operate with a grate or with an elevated fire. Always
build the fire on the surface of the firebrick.
16. Please read this entire manual before you install and use your
new room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
17. Check all local building and safety codes before installation.
The installation instructions and appropriate code require-
ments must be followed exactly and without compromise.
In the absence of local codes the following standards and
codes must be followed.
18. In the U.S.A, install in accordance with the National Fire
Protection Association’s Code, NFPA 211, Standards for
Chimneys, Fireplaces, Vents and Solid-Fuel-Burning Appli-
ances, or similar regulations, may apply to the installation of
a Solid-Fuel-Burning appliance in your area. In Canada, the
guideline is establishedby theCSA Standard,CAN/CSA-B365-
M93, Installation Code for Solid-Fuel-Burning Appliances and
Equipment.
19. Do not connect to any air distribution duct or system.
20. WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL)
CAN RESULT IN CARBON MONOXIDE POISONING, WHICH
MAY LEAD TO DEATH!
21. Carbon Monoxide Poisoning – Early signs of carbon monox-
ide poisoning resemble the flu with headaches, dizziness, or
nausea. If you have these signs, get fresh air at once! Have
the heater inspected by a qualified service technician. Some
people are more affected by carbon monoxide than others.
These include pregnant women, people with heart or lung
disease or anemia, those under the influence of alcohol, and
those at high altitudes.
22. Failure to use manufacturer provided parts, variations in tech-
niques and construction materials or practices other than those
described in this manual may create a fire hazard and void the
limited warranty.
23. Do not make any make-shift compromises during installation.
Any modification or alteration may result in damage to the
appliance or dwelling and will void the warranty, certification
and listings of this unit.
24. These appliances are designed as supplemental heaters.
Therefore, it is advisable to have an alternate heat source
when installed in a dwelling.

3
Table of Contents
General Safety Precautions .................................................................2
Testing Information...........................................................................4
Draft Requirements...........................................................................4
Selecting the Proper Venting System......................................................4
Negative Pressure Warning ................................................................5
Creosote........................................................................................5
Ash Disposal...................................................................................5
Fuel ............................................................................................5
Burn-In Period.................................................................................5
Paint Curing ...................................................................................5
Clearances to Combustibles ................................................................6
Floor Protection ...............................................................................6
Reduced Clearances .........................................................................6
Alcove Clearances ............................................................................6
Mobile Home Installations ..................................................................6
Chimney and Connector .....................................................................6
Components Required for Installation.....................................................6
Installation Clearances Diagrams..........................................................7
Legs Installation and Heatshield Installation ............................................8
Outside Air Kit Installation ..................................................................8
Stove Installation .............................................................................9
Pedestal Installation .........................................................................10
Post Installation Checks .....................................................................11
Brick Installation..............................................................................11
Optional Blower Installation ................................................................13
Operating Hints ...............................................................................13
Starting and Maintaining a Fire ............................................................14
Cleaning Glass ................................................................................15
Operating Techniques and Hints............................................................15
Getting the Most Out of Your Stove ........................................................15
Maximizing Your Stove’s Overall Efficiency ..............................................16
Achieving Clean, Long Burns ...............................................................16
Maintenance...................................................................................17
Troubleshooting ...............................................................................18
Do’s and Don’ts ...............................................................................19
Replacement Parts Lists.....................................................................20
Accessories....................................................................................21
Product Reference Information .............................................................22

4
Testing Information
This manual describes the installation and operation of the Can-
yon™ ST310 non-catalytic wood heaters. These heaters meet
the U.S. Environmental Protection Agency’s emissions limits for
wood heaters sold on or after July 1, 1990. This heater has been
developed, tested and constructed in accordance with the require-
ments of UL 1482, ULC S627 and HUD standards and is listed by
OMNI Test Laboratories, Beaverton, OR. It has been approved for
residential, mobile home and alcove installations.
Draft Requirements
Your woodstoveis dependentupona properlyfunctioningchimney
for optimum performance. It is a high efficiency appliance that
loses much less heat up the chimney than older appliances and
fireplaces. For this reason it is important to match the stove to
the chimney. The chimney has two functions:
1. It draws combustion air into the appliance (without air, no fuel
will burn) and
2. It exhausts combustion by-products. Your new Country™ Col-
lection stove is what is known as a “natural draft” appliance.
The appliance depends solely on the natural draft of the chimney
system to draw combustion air into the unit. Draft is the force that
moves air from the appliance up into the chimney. The amount of
draft in your chimney depends on the length of the chimney, local
geography, nearby obstructions and other factors. Too much draft
may cause excessive temperatures in the appliance (overfiring).
Slow or inadequate draft equals poor combustion and possible
smoking problems. The following are some conditions that may
contribute to poor chimney draft:
1. A chimney too large for your appliance.
2. A chimney with not enough height to produce adequate
draft.
3. A chimney with excessive height (this may allow exhaust
to cool too much before exiting, which will stall the rate the
exhaust exits).
4. Offsets in the venting system are too restrictive (see Chimney
Guidelines).
Inadequate draft will cause the appliance to leak smoke into the
room through the stove and the chimney connector joints.
Excessive draft may cause an uncontrollable burn or a glowing
red stove or chimney part.
Overfiring Damage - If the heater or chimney connector glows,
you are overfiring. Other symptoms may include: Cracking,
warping or burning out of components, plated doors may turn
color, stove glass may develop a haze, which will not come off
with cleaning.
Overfiring of a stove is a condition where excessive temperatures
are reached, beyond the design capabilities of the appliance. The
damage that occurs from overfiring is not covered under the
manufacturer’s limited warranty.
Also see Troubleshooting on Page 18.
Selecting the Proper Venting System
The appliance is merely one component of a larger system. The
other equally important component is the venting system. This is
necessary for achieving the required flow of combustion air to the
firechamberandforsafelyremovingunwantedcombustionbyprod-
ucts from the appliance. If the venting system’s design does not
promote these ends, the system may not function properly. Poorly
functioning venting systems may create performance problems as
well as be a safety hazard. A draft test should read greater than
.04’ W.C. (inches water column) and less than .08” W.C. As
per NFPA-211 standard (see paragraph below), the installer must
take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements
of the appliance. See Chimney Guidelines below to assist you in
selecting the proper venting system for your installation.
American National Standards Institute ANSI/NFPA 211, Standard
for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appli-
ances - See Draft Section: A chimney or vent shall be so designed
and constructed to develop a flow sufficient to completely remove
all flue and vent gases to the outside atmosphere. The venting
system shall satisfy the draft requirements of the connected ap-
pliance in accordance with the manufacturer’s instructions.
Chimney Guidelines:
• This appliance requires approximately 12 feet minimum of
“effective draw” provided by the venting system. As a rule of
thumb, every 90 degree total direction change in the venting
will result in a loss of approximately 5 feet of “effective draw.”
Example: If two 45 degree offsets are used, subtract 5 feet
from the actual vertical vent height to determine your “effec-
tive draw.” In this case if you had 14 feet of vertical vent, the
effective draw would only be approximately 9 feet (14 ft. - 5 ft.
= 9 ft.), therefore it may be necessary to add additional height
to the venting system.
• Do not install an offset within the first two feet above the flue
outlet on the appliance.
• If the venting system is all vertical and the total vent length
above the flue outlet exceeds 14 feet, it is recommended that
the 8” to 6” pipe reducer is used (cat. no. 71134) and a 6”
venting system be installed. At higher elevations, this may not
be necessary.
• In well insulated and weather tight homes, it may be difficult
to establish a good draft up your chimney. The poor draft is
caused by a shortage of air in the house. In this situation an
Outside Air Kit may need to be installed (See Negative Pres-
sure Warning on Page 5 and Outside Combustion Air on Page
8).

5
Dry, seasoned wood is that which has been cut, split and allowed
to dry under a covered area where air is free to flow and circulate
under and around the wood (not under a tarp or plastic). Make
sure wood is not stacked directly on the ground, it may absorb
moisture from the ground. It should be allowed to dry in these
conditions for a minimum of six months, preferably one year
or more. IT MUST BE UNDERSTOOD THAT WOOD CANNOT BE
LEFT IN ANY KIND OF WET OR DAMP AREA OR IT WILL NEVER
BECOME COMPLETELY SEASONED.
Your stove will not operate at the level that it is meant to unless
you use seasoned, dry wood. Do not burn driftwood or wood that
has been in salt water, doing so will void your warranty. Do not
burn treated wood, coal, garbage, cardboard, solvents, or colored
paper. Burning treated wood, garbage, solvents, or colored paper
may result in the release of toxic fumes. This type of burning will
also void your warranty.
Burn-In Period
If your stove has a Gold or Nickel-Plated Door, be sure to clean
it with a household type glass cleaner and a very soft cloth to
remove any fingerprints and residues prior to the first fire and
before any fire if the gold has been handled or soiled. Do not
close the door tightly during the “Burn-In Period.” Also, open
the door frequently (every 5-10 minutes) to keep the gasket
from adhering to the curing paint. Ventilate the house well dur-
ing these first firings as the paint gives off carbon dioxide and
unpleasant odors. It is recommended that persons sensitive to
an imbalance in the indoor air quality avoid the stove during the
curing process.
Please be patient with the heat output of your stove for the first few
weeks. The steel will go through a curing process that eliminates
moisture, which is deep in the steel and firebrick. This moisture will
reduce initial heat output of your stove and may make it difficult
to start. After you have broken in the paint on the stove it will be
necessary to build hot fires to thoroughly remove the moisture
from the appliance. Running the stove with the draft fully open
for 1 to 1-1/2 hours after starting and adding generous amounts
of fuel during the first week or two should complete the curing
process. We recommend the use of a thermometer attached to
the stovetop or chimney. Temperatures on the connector pipe
should run in the 250-600 degree range. (DO NOT OVERFIRE THE
STOVE DURING THIS PROCESS. IF THE STOVE OR CHIMNEY
BECOMES RED, REDUCE THE AMOUNT OF AIR ENTERING THE
STOVE IMMEDIATELY).
Paint Curing
Your new Canyon™ ST310 is painted with a high temperature paint
that cures during the first few firings. We recommend that you put
your stove through a regimen of three burns. The first two should
last for 20 minutes each at 250 degrees (the stove should be al-
lowed to cool completely between each burn). The third should
be a burn of at least 450 degrees F. for 45-60 minutes. The paint
will become soft, gummy and emit non-toxic smoke during these
burns. After the stove cools down for the third time, the paint will
harden. DO NOT BUILD A LARGE ROARING FIRE UNTIL THIS
CURING EFFECT IS COMPLETE OR YOU MAY DAMAGE THE FIN-
ISH OF YOUR STOVE. Spray can touch-ups should be done only
with a high temperature stove paint (cat. no. 70K99), available
from all Lennox Hearth Products dealers.
Negative Pressure Warning
This appliance is not designed to be operated in a negative pres-
sure. Very airtight homes with large kitchen exhaust fans, or
homes with furnace cold air returns located in close proximity
to the wood stove or fireplace insert may create negative pres-
sure in the same room as the heating appliance. This can create
dangerous back drafting of the stove and chimney joints, drawing
combustion by-products into the home. Be sure your home has
adequate makeup air to eliminate negative pressures caused by
the above-mentioned sources. Outside air connected to the ap-
pliance probably will not resolve such a problem as the stove or
fireplace insert is not the source of negative pressure. Lennox
Hearth Products accepts no liability for damages resulting from
negative pressures described here.
Ventilation Requirements - Provide adequate air for combustion.
The fresh air requirements of this appliance must be met within
the space where it will be installed. Ventilation is essential when
using a Solid-Fuel-Burning heater. In well insulated and weather
tight homes, it may be difficult to establish a good draft up the
chimney (caused by a shortage of air in the home). The lack of air
is caused by many common household appliances which exhaust
air from the home (such as a furnace, heat pump, air conditioner,
clothesdryer,exhaustfans, fireplaces,andother fuelburningappli-
ances). Also, the combustion process of this heater uses oxygen
from inside the dwelling. If the available fresh air delivery in the
dwellingisinsufficientto supportthedemandsof theseappliances,
problems can result (i.e. excessive negative pressure can develop
in the dwelling which will affect the rate at which this appliance
can draft thus resulting in performance problems. To correct this
problem it may help to open a window (preferably on the windward
side of the house) or install an optional outside air kit.
Creosote Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic
vapors, which combine with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool chimney flue of
a slow-burning fire. As a result, creosote residue accumulates on
the flue lining. When ignited, this creosote makes an extremely hot
fire. The chimney and chimney connector should be inspected at
least onceeverytwomonths during theheatingseasonto determine
if a creosote build-up has occurred. If creosote has accumulated,
it should be removed to reduce the risk of a chimney fire.
Ash Disposal
Ashes should be scooped out of a cool stove with a small metal
shovel. Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be placed on
a non-combustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally dispersed, they
should be retained in the closed container until all the cinders
have thoroughly cooled. Ashes can ignite up to 72 hours after
removal from the stove.
Fuel
This unit is designed and engineered to burn, dry, well-seasoned
wood only.

6
Clearances to Combustibles
WARNING: BE ABSOLUTELY SURE THE DISTANCE
BETWEEN THE HEATER AND THE SURFACE OF ANY
COMBUSTIBLE CONSTRUCTION IS NOT LESS THAN
SHOWN.
Floor Protection
USA - The floor in front and under the heater must be protected
with a minimum of 3/8” thick noncombustible material. The cover-
ing must extend 16” in front of the door opening of the heater and
8” to either side of the door opening and 5-1/2” to the rear or to
the wall, whichever is smaller. In all installations a 16” minimum
hearth extension (in front of the stove) is required as measured
from the door opening of the unit.
Canada - The floor in front and under the heater must be protected
witha minimumof3/8”thicknoncombustiblematerial.The covering
must extend 457 mm in front of the door opening of the heater and
200 mm to either side of the stove body and 200 mm to the rear
or to the wall, whichever is smaller. In all installations a 457mm
minimum hearth extension (in front of the stove) is required as
measured from the door opening of the unit.
Reduced Clearances
Clearances to combustible surfaces can be reduced with the use of
listed double wall connector pipe. See the clearances with double
wall pipe on the following page.
Alcove Clearances:
In alcove installations, only 6” or 8” double wall connector pipe
must be used (single wall or single wall pipe with shield is not
allowed). Minimum alcove width between combustible materi-
als is 56-1/2”. Maximum alcove depth is 48”. Minimum alcove
height is 72”.
Mobile Home Installations
This appliance is approved for installation into a mobile home
in the USA ONLY!
Installation should be in accordance with the Mobile Home
Construction and Safety Standard, Title 24 CFR, Part 3280 (in
Canada CAN/CSA Z240 MH), or, when such a standard is not
applicable, the Standard for Mobile Home Installations, ANSI
A225.1.
All mobile home installations require an outside air kit (Cat. no.
71111 or 71112). The stove must be bolted to the floor and
grounded to the chassis of the mobile home.
WARNING: DO NOT INSTALL IN SLEEPING ROOM
OF A MOBILE HOME.
CAUTION: THE STRUCTURAL INTEGRITY OF THE
MOBILE HOME FLOOR, WALL AND CEILING/ROOF
MUST BE MAINTAINED.
Approved Chimney* - Your stove is approved for use with double
wall connector pipe from Security™ Chimneys.
THIS APPLIANCE IS NOT APPROVED FOR USE WITH
SINGLE WALL PIPE. USE DOUBLE WALL CONNEC-
TOR PIPE ONLY.
Clearances to connector pipe shall be measured from the flue
collar of the stove.
Chimney and Connector
May only be installed using listed 6" or 8” double wall connector
pipe with listed factory-built chimney suitable for use with solid
fuels or masonry chimney. Horizontal connections not tested,
refer to local building codes for installation. May be installed
with 6” connector pipe and chimney using an 8” to 6” reducer.
See installation instructions for details. Clearances to connector
shall be measured from 8" flue collar. Restrictions apply! Read
instructions before installing.
The Canyon™ ST310 may be installed using 6” chimney in verti-
cal installations utilizing a 8” to 6” reducer (cat. # 71134) at the
flue collar. If the venting system is all vertical and the total vent
length above the flue outlet exceeds 14 feet, it is recommended
that the 8” to 6” pipe reducer is used and a 6” venting system
be installed.
Residential chimney systems must be from the same brands of
double wall pipe as listed for mobile homes.
Connector pipe and chimney must be of the same brand.
Thechimneyconnectorshall notpassthrough anatticorroofspace,
closet or similar concealed space, or a floor, or ceiling. Where
passage through a wall, or partition of combustible construction
is desired, the installation shall conform to CAN/CSA-B365.
There must be an effective vapor barrier at the location where
the chimney or other component penetrates to the exterior of the
structure. Follow the vent manufacturer's detailed instructions.
IMPORTANT NOTE: See Draft Requirements and Selecting a
Proper Venting System on Page 4 to assist you in choosing the
proper venting system for your installation.
Components Required For Installation
Legs AND bottom heat shield or pedestal.
WARNING: In the event that you remove the blower for any
reason, make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive rear
wall temperatures will result if the stove is burned without the
cover plate. Note: The cover plate is not necessary if a blower
has never been installed because a knock-out will be in place
to act as the cover.
* Other approved chimney brands are Projet, Jakes Evans/GSW, Dura-vent,
Metal Fab, Ameri-Tec, Metalbestos and Industrial Chimney (ICC).

7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Diagram A: Top View-Parallel Installation Diagram B: Side View-Alcove Installation
PIPE INSTALLATION A B(1) C D(1) E† F(1,4) G(4) H (2) I (6)
Double Wall Residential or Alcove 12"
305mm
9-1/2"
241mm
24"
610mm
14"
356mm
8"
200mm
7-1/4”
184mm
18"
450mm
USA-43-1/2”
CAN-1308mm
USA-53”
CAN-1346mm
6” or 8”
Diameter
Mobile Home* 12"
305mm
9-1/2"
241mm
24"
610mm
14"
356mm
8"
200mm
7-1/4”
184mm
18"
450mm
USA-43-1/2”
CAN-1308mm
USA-53”
CAN-1346mm
PIPE INSTALLATION J (2) K L M N u T (6)
Double Wall Residential or Alcove USA-38”
CAN-1130mm
20”
508mm
USA-0”
CAN-200mm
72"
1829mm
39-1/2"
1003mm
USA-68”
CAN-1727mm
6” or 8”
Diameter
Mobile Home* USA-38”
CAN-1130mm
20”
508mm
USA-0”
CAN-200mm
72"
1829mm
39-1/2"
1003mm
USA-68”
CAN-1727mm
Installation Clearances - Refer to Diagrams A, B and C
Alcove, Residential, or Mobile Home
6” or 8” Double Wall Air Cooled
Footnotes:
1 - Thesedimensionsto the stovebody arefor
reference only. Actualdistancesshouldbe
measured from the stove’s flue collar.
2 - Minimum noncombustible hearth pad
dimensions.
3 - Shield shall be attached to the rear of the
stovepipe witha1” air spaceand must run
from the top of the stove to the ceiling.
4 - Not applicable to alcove installations.
5- In corner applications, when installed
at minimum back wall clearances, the
required floor protection is dimensioned
off the back plane of the stove, therefore
the floor protection required off the back
corners (at a 45 degree angle) only needs
to extend to the wall. This situation will
only occur in CANADA installations.
6- Reference dimension only, to assist in
planning the installation.
Clearances to connector pipe shall be mea-
sured from the flue collar of the stove.
Diagram C: Top View- Corner Clearance, Stove and Flue to Wall
† USA=8" (200mm) from door opening, Canada=8" (200mm) from sides and back of unit
u Dimensions to Stove Body
* Mobile Home - USA only
B A L
C
D
†E †E
K
Floor Protection
H
I
J
M
N
I
Floor Protection
K
T
J
H
Floor Protection
F
F
GG
Combustible Wall
48”
Max.
Depth
8” Ø
Flue Collar

8NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Heat Shield
Mounting Holes
Air Channel
Front
Figure 2
Figure 1
Outside Air Kit Installation
To install the “Outside Air Kit,” position the clip so that the nut is
directly above the hole punched in the back of the heatshield (See
Figure 3). Install the outside air adapter box on the stove by slid-
ing it into the air channel located between the bottom heatshield
and the stove bottom until the oblong ring is approximately 1/4”
from the rear edge of the lower heatshield. Make sure the ring is
facing down. Thread the 1/4” bolt up through the nut in the clip
until snug against the adapter box.
To locate the hole in the hearth for outside air, mark a 4” circle on
the hearth. The circle’s center should be 2-3/4” directly back from
the center of the flue outlet and 5/8” to the left side.
Figure 3
Expanded View of Clip
Leg and Heatshield Installation
Note: The threaded rods used to bolt the legs to the stove are
packaged with the heatshield, as a heatshield is required when a
stove is installed on legs.
Residential and Mobile Homes
(Bolting down and grounding of stove are required only in
mobile homes).
Open all cartons, if any and remove the contents upon receipt
and check for any damaged or missing parts. If there is hidden
damage, notify your freight company or Lennox Hearth Products
dealer immediately.
CAUTION: Wear gloves during installation in case of
sharp edges on the stove.
Leg Installation
1. Carefully place stove on its back. Be careful not to scratch
the stove, use a piece of cardboard or carpet to protect
the back of the stove.
2. Mount all four legs as shown in FIGURE 1 below.
3. First, screw the threaded rods into the holes at the four
corners on the bottom of the stove. Screw the threaded
rods into the firebox three full rotations or 3/16 to 1/4”
(if the rear rods are screwed in too far they will lift the
bricks off the bottom of the stove). Use a washer and nut
to secure the leg. Be sure the legs are mounted squarely
on the firebox bottom. Tighten nuts securely.
4. Use the two bolts and washers provided with the heatshield
kit to mount the heatshield as shown in Figure 2.
5. Do not over tighten the heatshield mounting bolts as it
may bend the heatshield.
Line up the hole in the clip with the hole in the
rear center of the bottom heatshield
Threaded Rod
Washer
Nut
Clip
1/4” Bolt

9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Stove Installation
1. If not previously installed, install floor protection and move
the heater into the desired location.
2. Position the stove on your floor protection in the exact
location where it is to be located, making sure all minimum
clearances are met.
3. If you are installing outside air on your stove, mark a 4” circle
on the floor protection just below the oblong ring. When
cut out, this hole will accommodate the flexible outside air
tube.
4. If the stove is to be fastened to the floor, locate the hold down
brackets inside the leg box and mark the floor protection
below the holes in the brackets.
5. If you are installing outside air on your stove, remove the
stove and cut the floor protection and the floor where the
4” air tube circle had been previously drawn. If the stove is
to be fastened to the floor, drill 1/2” holes through the floor
protection only, at the marks that were for fastening the
stove to the floor if so desired. Slip the flexible outside air
tube through the hole in the floor, leaving 1” of tube above
the floor protector surface, using tape to hold it in place.
6. Place the stove on the floor protection so that the previously
cut or drilled holes line up. Attach the stove to the floor with
the lag bolts if so desired.
7. If you are installing outside air on your stove place the hose
clamp over the flexible air tube and slide the tube up over the
4” ring on the outside air adaptor box and tighten the hose
clamp. Push the outside air adaptor forward 1/4” until full
contact is made with the lower heatshield. Tighten the 1/4”
bolt until the adaptor box is held firmly in place. Use silicone
sealant to create a seal between the flexible air tube and your
floor protection.
8. If it is necessary to level, secure, or ground your stove, use
the holes in the bottom of the leg for those applications. To
level the stove on Olympic cast legs, locate the front leg that
is not touching the hearth pad. Insert the allen head screw
through the slotted washer (supplied with the legs) and into
the threaded hole in the bottom of the leg. See the drawing to
the right. Push the slotted washer down until it touches the
hearth pad and then tighten the screw into the leg. Should any
other leg not be resting on the hearth pad, install a washer
and screw in that leg as well.
9. Install bricks and baffle as per instructions on Page 11. It is
highly recommended that the baffle be assembled before the
chimney is installed so that the insulating fiber blankets can
be adjusted into place through the flue collar.
10. If installed into a mobile home, the stove shall be grounded
to the mobile home chassis with a #8 AGW copper wire or
equivalent.
11. For residential installations, install the first section of stove
pipe with the crimped end going down inside the flue collar
on the heater. Continue with your stove pipe, installing each
section-crimped end down. Make the final connection to your
chimney. Your dealer carries the necessary pipe and fittings
to connect to the various listed factory-built chimneys. YOUR
CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.
12. Be sure to fasten each stove pipe connection with at least 3
sheet metal screws.
13. Install chimney as per manufacturer’s instructions. Some
brands of pipe may require removal of the spacer ring in the
flue collar.
14. All horizontal runs of pipe should be as short as possible and
are required by NFPA No. 211 to have an upward pitch or rise
in the same direction the smoke travels of no less than 1/4”
to the linear foot. The connector pipe must meet minimum
clearances in any direction to
walls or other combustible
materials. It must attach to
a listed double wall metal
chimney at least 6” in diameter
or to a masonry chimney with
a flue passage of at least 48
square inches.
15. It is required that a chimney
connector pipe not extend
further than the inner wall of
the flue when it is connected
to a masonry chimney and
that it either be cemented to
the masonry or be installed
without cement in a thimble
connected to the masonry
wall. When the connector is
inserted into a thimble, the
joint must be tight enough so
that it will not be dislodged in
normal use. Install connector
at no less than the minimum
clearances from the ceiling when using a 90-degree elbow
to pass through combustible constructions.
16. Chimney connector pipes should never pass through a floor,
ceiling, fire wall, partition, or combustible construction of any
type unless certain precautions are taken. The best method is
to use a listed thimble and a listed chimney in accordance with
the manufactures directions. NFPA No. 211 gives approved
methods for passing a flue pipe through combustible construc-
tions.
Figure 4
Insert the allen
head screw
through the
slotted washer

10 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Pedestal Installation
(For ash drawer pedestal see instructions included with pedestal)
Residential and Mobile Homes
(Bolting down and grounding are required only in mobile homes)
CAUTION:Wear gloves during installation in case of sharp
edges on the stove.
1. Remove the heater from the carton, if packaged, upon receipt
and check for any damaged or missing parts.
2. Carefully put the stove on pedestal with the open end of the
pedestal facing the rear. DO NOT LEAVE THE STOVE UNAT-
TENDED UNTIL IT IS BOLTED SECURELY TO THE PEDES-
TAL.
3. Line up the holes in the brackets on the pedestal with the
threaded holes in the bottom of the stove. Use the two 1/2”
long bolts and 3/8” standard washers to bolt the stove to the
pedestal. Be sure to see that the stove is mounted squarely
on the pedestal before tightening the two bolts securely.
4. When installing a pedestal on this stove you MUST plug the
four leg mounting bolt holes, on the bottom of the stove in
the four front corners, with the bolts that were used to mount
the shipping legs. The two rear bolts should not be installed
more the two full rotations to prevent lifting the bricks off
the bottom of the stove. FAILURE TO INSTALL THESE FOUR
BOLTS PROPERLY WILL RESULT IN REDUCED CONTROL OF
THE STOVE’S COMBUSTION SYSTEM!
5. If required, install the Outside Air Kit (cat. no. 71112) as per
the following instructions. To locate the hole in the hearth for
outside air mark and cut a 4” (102 mm) hole in the hearth.
The hole’s center should be 3” (76 mm) directly forward from
the center of the flue outlet or locate as per the instructions
below.
6. Position the stove on your floor protection in the exact loca-
tion where it is to be located, making sure all minimum clear-
ances are met. Mark the floor protection where the pedestal
will be located, then remove the stove.
7. Make four 1-1/2” (38 mm) cuts in one end of the corrugated
tube and fold the flaps back. Cut a 4” (102 mm) hole through
the floor protection and the floor and insert the corrugated
tube into the hole. Cover it with the supplied screen and fasten
it to the floor protector.
8. Locate the 11-1/2” x 14” (292 mm x 356 mm) metal plate
and paint to match the stove if necessary. Position this piece
so that the 14” (356 mm) dimension evenly overlaps the lips
on the back of the pedestal (see drawing below). Attach this
plate to the back of the pedestal with the self-tapping screws
supplied.
9. If the stove is to be fastened to the floor, attach the stove with
the supplied lag bolts, through the pedestal base on opposite
sides, attaching them into the floor beneath the floor protec-
tion. Seal any irregularities with silicone sealer.
10. If installed in a mobile home, the heater shall be grounded
to the chassis with a #8 AGW copper wire or equivalent.
11. Install bricks as per instructions on Page 11. It is highly rec-
ommended that the baffle be assembled before the chimney
is installed so that the ceramic fiber blankets can be adjusted
into place from the flue outlet.
12. Install chimney as per manufacturer’s instructions.
Block Off Plate is
Required When
Installing Outside
Air Into Unit (Plate
is Included With
Kit # OAK-P)
Figure 5

11
Post Installation Checks
1. Check that all chimney pipe joints are securely fastened.
2. Check that the heater is securely fastened to the floor (if ap-
plicable).
3. Make sure the intake vent has clear access to outside air (if
applicable).
4. Make sure the outside air vent has been sealed properly to
keep rodents out (if applicable).
5. Be sure all roof flashings are watertight.
6. Be sure the stove is properly grounded (if applicable).
FOR YOUR OWN PROTECTION AND INSURANCE PUR-
POSES, HAVE YOUR CHIMNEY AND CONNECTOR PIPE
INSTALLATION INSPECTED BY YOUR LOCAL BUILDING
CODE AUTHORITY OR FIRE MARSHAL BEFORE START-
ING A FIRE IN YOUR STOVE. NOTIFY YOUR INSURANCE
COMPANY.
Brick Installation
CAUTION: Wear gloves during brick installation in case
of sharp edges inside the stove.
Note: Installation of the baffle bricks and insulating blanket is
easier when you can still access the flue outlet, (before connect-
ing the flue pipe). Be sure the insulating blanket is placed flat
on the bricks so as not to block the flue. Use a ruler or a piece of
kindling to reach over the blanket to be sure it is completely flat
on top of the baffle bricks.
Measure bricks before installing, as per list of dimensions on
next page, to be sure the correct bricks are installed in the cor-
rect location.
1. Install bricks #1-34 in the numbered sequence shown in Fig-
ure 6A on the following page. Note: Bricks # 22-25 lean up
against the lower air channel and butt against bricks #17-21
on the bottom of the stove.
Note: Before installing your baffle bricks make sure the stain-
less steel tube support and front and rear tube hangers are
centered side to side and that the front and rear hangers are
hooked onto the stainless steel pins protruding from the rear
of the airwash and the stove back.
2. Next install bricks #35-40 on top of the stainless steel sec-
ondary burn tubes in the upper part of the firebox. These
bricks fit up against bricks #26-30 on the backwall and should
rest on the rear two stainless steel secondary tubes. These
two sets of three bricks go either side of the stainless steel
secondary tube support running front to rear down the center
of the stove.
3. Be sure the stainless steel tube support is in the center, as
shown and that its two stabilizer pieces in the front and the
rear are attached to the two hooks welded to the firebox front
and rear.
4. Included with the stove are two 13” x 17-1/2” x 1” thick ce-
ramic fiber blankets. Install a ceramic fiber blanket on top of
each set of three bricks, making sure the blankets are pushed
fully to the rear.
5. Next, install the front baffle bricks #41-46 under the ceramic
fiber blanket and on top of the front two stainless steel sec-
ondary tubes. (CAUTION: Make sure that the ceramic fiber
blankets are centered side to side and rest flat on the baffle
bricks and do not project forward beyond the front of the
baffle bricks #41-46).

12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
These brick sizes may be slightly smaller to adjust for steel and firebrick tolerances beyond our control. Be sure to measure and
mark bricks with their numbers when removing.
WARNING: IF THE BRICKS ARE NOT INSTALLED EXACTLY AS SHOWN BELOW, THEY COULD FALL OUT OF PLACE
DURING REFUELING OR BURNING OF THE STOVECAUSING SERIOUS INJURY.
1/2”
Side View
M Brick
2-1/2” M
4-1/2”
35
F
36
F
37
G
40
G
39
F
38
F
44
J
45
J
46
K
43
K
42
J
41
J
* These bricks go up against the stoves back wall
Baffle Brick Layout
Stainless Steel Tube Support
Rear Brick
Go Behind
Baffle Brick
Secondary Burn Tubes
Baffle
Brick
Figure 6B Figure 6C
Brick Sizes
A 3-7/8” X 8-3/4”
B 6-1/2” X 4-1/2”
C 3-1/2” X 9”
D 1-1/2” X 4-1/2”
E 3-7/8” X 9”
F 4-1/2” X 9”
G 3” X 9”
H 3-1/2” X 4-1/2”
J 4-1/2” X 7”
K 3” X 7”
M 4-1/2” X 4-1/2”
Insulating Blanket
Figure 6A

13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Operating Hints
1. Burnonlydry,well-seasonedwoodformaximumheat
output. In some states it is illegal to burn wet wood
or anything other than clean, dry wood products.
2. Your stove is designed to operate with the door
closed! Operate only with the door shut tightly at
all times except when loading wood.
3. DO NOT hit or move the baffle brick while loading
wood. Occasionally check the baffle. Make sure the
insulating blanket is always flush with the front of
thebafflebrick.Loading oversizedlogsmay dislodge
the baffle bricks.
4. CAUTION: THE DRAFT CONTROL MUST BE FULLY
OPEN BEFORE OPENING THE DOOR TO AVOID
POSSIBLE COMBUSTION FLASH!! (Ignition of hot
volatile gases as the door is opened).
5. Feedingexcessiveamountsoffueltothestove should
be avoided. It is important to supply it with sufficient
draft and fuel to maintain a moderately hot fire. If,
during overnight burns, heavy creosote deposits
develop inside your stove and on the door, the draft
is set too low - review your burning habits!
Optional Blower Installation
A blower, cat. no. 71000, can be installed on the stove to improve
hot air distribution throughout the room.
To install the blower:
1. Remove all the contents from the blower box. Included
with the blower should be a blower speed control.
2. Remove the screw in the round knock-out plate on the
back of the stove. Bend the knock-out plate back and
forth until it can be removed.
3. Mount the blower as shown below. Make sure the cord is
at the bottom when mounted and that it does not touch
the stove anywhere. Remove the four screws from the
back of the stove. Use one of the four screws with a
washer on it and attach the blower through one of the
fourmountinglegs onthe blowerhousing.Check tomake
sure that the fan blade does not touch the large hole in
the rear heatshield. (Spin it to check all directions). Finish
attaching the blower with the other three screws. Tighten
the screws moderately tight but do not over tighten as
you may strip the holes out.
4. Plug in the fan speed control into the nearest outlet, then
plug the blower cord into the speed control. Do not route
the fan power cord under the stove or allow it to come in
contact with any surface of the stove. Read the section
Starting and Maintaining a Fire for proper fan operating
instructions on Page 15.
WARNING: In the event that you remove the blower
for any reason, make sure a cover plate (available
from Lennox Hearth Products) is installed before us-
ing the heater. Excessive rear wall temperatures will
result if the stove is burned without the cover plate.
Note: The cover plate is not necessary if a blower has
never been installed because a knock-out will be in
place to act as the cover.
CAUTION
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replace-
ment parts.
WARNINGS
The blower must be plugged directly into a properly
groundedthree-prong receptacle,120VAC,60Hz,single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
Installation must be in accordance with National Elec-
trical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA C22-1 Canadian Electrical Code - latest
edition.
DANGER: Disconnect power before servicing blower.
Figure 7

14 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Starting and Maintaining a Fire
Be sure to clean the Nickel or Gold Plated door with household
typeglasscleanerand avery softclothtoremoveanyfingerprints
and residues prior to the first fire.
1. NEVER USE FLAMMABLE LIQUIDS TO START OR RE-
KINDLE A SOLID FUEL FIRE!!
2. Fully open the primary draft control by pulling the 1”
plastic knob out on the left side (lower front corner) until
it stops (away from the stove). This control determines
the amount of air entering the stove. Pushing it toward
the stove reduces the burn rate in the firebox. For your
convenience, the rod on this control is marked with
four grooves to assist you in obtaining repeatable burn
rates.
3. Place a small amount of crumpled paper in front of the
firebox and cover it with a few pieces of kindling.
4. Light the paper and allow sufficient time for the kindling
to become fully engulfed in flames. Close the door. Your
door may or may not need to be left slightly open dur-
ing this process, depending on your stove model and
chimney draft. Once the kindling is burning well, larger
pieces of wood may be added, then the door should be
closed.
Do not operate the stove with the doors open or ajar,
as this will produce extreme temperatures within the
stove. Damage caused from over-firing is not covered
under the manufacturers limited warranty.
5. For best results, use smaller pieces of wood to get the
stove temperature very high before loading larger wood
for sustained burns. If necessary, crack the door to al-
low ignition of the fuel charge. Now you can add larger
pieces of wood and after several minutes of high burn,
set the left control for the desired heat output. Check the
exhaust in about 15 to 20 minutes. Large amounts of
smoke indicate an improper burn setting (either too high
or too low). Adjust and recheck in 5 to 10 minutes.
6. After your stove has been thoroughly preheated, your
blower can be switched on. When refueling your stove,
turn the blower off for the first 30 minutes. On low and
medium-low burns run the blower on low. These burn
rates would be achieved by operating the stove with the
draft rod fully pushed in to up to 3/4” open (out). To do
this, turn on the blower at the speed control and rotate
the control all the way to the right. On medium-high and
high burns you may run the blower on high. These burn
rates would be achieved by opening the draft rod further
than stated previously. To do this, turn on the blower with
the speed control and do not rotate the switch after it
clicks on.
Figure 8

15
Operating Techniques and Hints
Recentdevelopmentsinwoodburningtechnologyhavemadewood
burning a cleaner and more convenient way to heat your home.
Overall efficiency in a wood burning appliance is a combination of
combustionefficiency andheattransferefficiency.Whetherheating
your entire home, or just a room or two, your understanding of
how to best operate your stove or insert will enhance its overall
efficiency and performance. What this can mean to you is longer,
cleaner burns, less wood use and more heat.
Getting the Most Out of Your Stove
The following sections will outline techniques you can use to “get
the most out of your stove.” Please read them carefully.
Cleaning Glass
SEE MAINTENANCE ON PAGE 18 FOR GLASS CLEANING TIPS
The operator plays an important part in keeping the glass clean and
free of build-ups. The first and most important part the operator
plays is making sure to burn only well-seasoned firewood. Wet
wood = Dirty glass. Keeping your glass door clean is partly ac-
complishedbythe air washsystem ofthe stove,which sendsclean,
fresh air for combustion, over the window before it enters the fire.
The high temperatures inside the firebox also keep the glass clean.
No stove door stays perfectly clean. The following are methods
for keeping build-up on your glass to a minimum. When properly
installed and operated by a knowledgeable operator, your glass
door should require very little maintenance. Do not expect to get
extremely long burn times and keep the window perfectly clean.
Cool temperatures cause condensation of unburned volatiles on
the glass. If your glass gets very dirty during overnight burning,
try preheating the stove a little longer before damping it down for
an overnight burn. Also, don’t damper your stove down as low
because you’ll get more heat for your money by burning a little
hotter for a slightly shorter time.
The air wash system will perform at its best at medium burn rates.
Some stove models will self clean by burning very hot fires but
be sure not to over-fire the stove. If it glows red it is over-fired.
Over-firing a stove also causes the window to soot up. Extremely
hot fires with fresh wood may cause the flow rate to exceed one
foot per second, which is as fast as a flame can burn. This is why
a candle goes out when you blow on it. Blow on it gently and it
burns brightly. Blow on it hard and it goes out. This will cause
excessive exhaust emissions and your window to soot up, as the
stove is unable to burn the gases emitted from the wood. Try
slowing the stove down a little by closing the damper somewhat
as it warms up.
Keeping freshly loaded wood away from the window will also help.
Load fresh logs in the rear of the firebox. Build-up tends to occur
first on the right side of the window. This is caused by the swirl-
ing motion of the exhaust gases similar to water running down a
drain. Keep fresh logs further back on the right side of the firebox
to help prevent this problem.
Understanding how your Country™ Collection stove works should
help you keep your glass door very clean, but as stated: no glass
door stays perfectly clean. We hope this information is helpful in
keeping your glass door clean so that you may enjoy many hours
viewing your high efficiency stove. For more information, contact
your Lennox Hearth Products dealer.
CAUTION
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasive cleaners. Do not clean with any materials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.

16
Maximizing Your Stove’s Overall Efficiency
It is important to know that for high, combustion efficient, clean
burns, you will need to have sufficient temperatures inside the
fireboxforthoroughcombustion.Thebestmethodfor determining
if you have sufficient temperatures is to watch the brick lining in
your firebox. When you first light your stove, the bricks will turn a
dark brown or black. After 20 to 30 minutes of a hot fire, most of
the bricks should return to near their original light brown or yellow
color. This means the bricks have reached a high enough tempera-
ture for your stove to achieve high combustion efficiency.
Second and just as important, is achieving a high level of heat
transfer efficiency. Slowing the rate of flow through the stove or
insert enhances heat transfer, thus allowing more time for heat to
be transferred into your home. To do this, be sure to thoroughly
preheat your stove and then reduce the amount of primary air
by closing the draft control (lower left) to about 1/2 to 3/4 open.
This will decrease the excess oxygen in your flue, which carries
heat up your chimney, but should still be enough air to allow the
stove to produce its maximum heat output. (More air may produce
a slightly greater amount of heat, but will greatly increase wood
consumption). When the area being heated reaches a comfortable
temperature, slow the burn rate by closing the control to further
improve heat transfer.
To get the most out of your stove, you will need to combine good
combustion efficiency with good heat transfer practices. The fol-
lowing are some tips on how to operate your stove to achieve the
highest overall efficiency.
1. Thoroughly preheat your stove before slowing the burn
rate by closing the draft control.
2. Measure the stove temperature at the hottest point on
the stove top or face. Use this information to repeat burn
rates.
3. Once preheated, add wood (if needed) and partially close
the draft control (lower left).
4. Operate your stove as much as possible in the low to
medium burn ranges.
5. Do not lower the draft setting so low as to completely
extinguish the flames in the firebox. Check for at least
some small flames twenty minutes after setting the draft
control.
6. Do not continually operate your stove in the high (wide
open) setting. This wastes wood by carrying a great deal
of heat up the chimney and can damage your stove and
chimney.
7. Go outside and check your chimney. More than a very
small amount of smoke indicates wasted heat, creosote
build-up and pollution.
Achieving Clean, Long Burns
To achieve long burn times, after having thoroughly preheated
the stove, let the stove top cool down to 275to 400 degrees (on
Elites, locate thermometer on the face of the insert just above
the door). Now load the firebox and set the draft control. At this
point, you may need to burn the stove with the draft open for a few
minutes to ignite the wood. All Country™ Collection stoves are EPA
tested for emissions at low burn with the air control completely
closed. Whether or not you should burn your stove with the air
control completely closed will depend on the following factors:
* How you load your wood
* Your chimney type, height and draft
* Your wood type and its moisture content
* The temperature of the stove
* Which model stove or insert you have

17
Experiment with different loading configurations to achieve
longer burns. Try loading the wood from side to side and nesting it
in the ashes to prevent airflow under and around the wood. Fresh
wood should be loaded to the back of the firebox or to the sides.
Hot coals or half burned wood should be brought towards the front
of the firebox. The way you load your wood can seriously affect
burn times. If the new load does not ignite within a few minutes,
try crisscrossing the load to allow more airflow around the fire,
or try a slightly hotter stove temperature.
Determining the lowest setting for efficient low burns. This
will require some experimentation on your part. Try closing the
air control all the way with the stove temperature at 325 to 350
degrees. If the flames are completely extinguished, open the air
control halfway and then slowly close it until there is only a small
amount of flame. It is important to check the stove about 20
minutes after setting the draft control as it takes this long for the
stove temperature to stabilize. There should still be some small
flames on or above the wood load.
Use 325 degrees as a starting point. You can try starting tem-
peratures 25 degrees higher or lower to achieve desired burn
times, start 25 degrees lower if the stove burns the wood too
quickly or 25 degrees higher if there are no flames in the firebox
for more than a few minutes after loading the wood. You may or
may not need to burn the stove with the air control open for a few
minutes prior to setting the draft for a low burn, this will depend
on the factors mentioned above. Be sure not to smolder a fire
overnight. Check your chimney for large amounts of smoke as
this indicates very poor combustion.
It is important to realize that stove technology has changed.
Stoves have changed a great deal in the last few years. This has
led to substantial changes in the methods of operation in new
stoves as compared to older stoves. In old stoves without full
brick linings and ceramic insulation, the rule was “get the stove
as hot as possible before setting the draft on low for overnight
burns.” On newer, high technology Country™ Collection stoves,
this is not necessary. Although it is still important to have the stove
hot enough to burn efficiently, it will require less preheating. Once
you have determined your optimum operating temperatures for
various burn rates, we believe you will find your stove an extremely
convenient way to achieve your heating needs.
Do not reload the stove for long burns when the stainless
secondary tubes or baffle supports are glowing red, or when
the stove is uncomfortably hot to load. This indicates the stove
is too hot to load for a long burn. Also, do not load wood for a
long burn on a deep bed of hot coals. Try stirring the coals a few
minutes before loading the stove for a low burn to allow some of
the unburned coals time to burn.
Maintenance
DOOR HINGES: If door hinges need lubricating, use an anti-seize
compound (never use oil) available from your Lennox Hearth
Products dealer.
DOOR LATCH: If your door latch fails to latch tightly and the gasket
is in good condition, place a length of pipe (cheater bar) over the
inside portion of the door handle and bend slightly toward the door
until the proper adjustment is obtained. If the door handle does not
close easily, apply high temperature anti-seize to the striker.
DOOR GASKET: Periodically check gasket to make sure it is not
over-compressed. If compressed, replace with a special woven
door rope. (Don’t try substituting rope, only use special Lennox
Hearth Products door rope).
GOLD OR NICKEL PLATED DOOR: Clean only with a household
type glass cleaner and a very soft cotton cloth. Other products
may damage brass, paint and gaskets.
INSULATING BLANKETS: Your insulating blanket should be
inspected during every chimney cleaning. If the blanket is com-
pressed or heavily stained, it should be replaced. Heavy creosote
stains or matting indication of improper use and your burning
habits should be reviewed.
GLASS CLEANING: Only clean glass with products specifically
madetouseon woodstoves.Otherproductscoulddamagegaskets
and paint. Never scrape glass with a razor blade. This can pit the
glass and make it impossible to clean in the future.
WINDOW GASKET: The window gasket can be checked by run-
ning the flame of a match near the gasket and around the door.
If the flame is drawn in around the window, the gasket should
be replaced.
DOOR HANDLE: Door handle may become tight as you use the
stove. Free the handle up by using dry graphite supplied with the
stove. The directions are included with the graphite.
WARNINGS
Inspectandcleanchimneyandconnector frequently.
Under certain conditions of use, creosote buildup
may occur rapidly.

18
Troubleshooting
Problem Solution
POOR DRAFT: Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys nor-
mally have poor drafts. Remember, the stoves’ draft depend solely on the natural draft of the chimney (See
Drafting section on Page 3). If your stove is not drafting properly, your chimney is the problem. All stoves
are thoroughly tested to ensure proper draft with the correct size chimney flue.
EXCESSIVE DRAFT: With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by
slowing the burn rate of the stove once it has reached proper operating temperature (See Maximizing Your
Stoves Overall Efficiency on Page 16).
DIRTY GLASS: 1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft
control.
2) Make sure your wood is well seasoned and dry (not open to rain - see Creosote and Fuel sections on
Page 4).
3) See Poor Draft section (above) and Cleaning Glass on Page 15.
SMOKES WHEN 1) If smoke is entering the room, check to make sure your baffle bricks are properly installed
DOOR IS OPEN: and that the insulating blanket is pushed back flush with the front of the baffle brick.
2) Check the chimney for blockage due to creosote (see Chimney and Creosote sections on Pages 3 and
4).
3) Check draft (See POOR DRAFT section above).
WOOD BURNS 1) The draft control must be closed further.
TOO FAST: 2) Add fuel at lower firebox temperatures.
3) Load wood side to side and reduce the flow of air under wood.
4) The door seal may need replacing, check for leakage.
5) See “Excessive Draft.”
POOR HEAT 1) Check your wood. Wet, moist, unseasoned wood will not produce heat.
OUTPUT: 2) Your stove needs to be seasoned (moisture removed from the steel and brick). Continue to burn a fire.
It normally takes from one to three weeks of burning to season your stove (See Burn-In Procedures on
Page 5).
3) See Excessive Draft section above.
PAINT GIVES OFF Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.
ODOR (smoke): Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See
Burn-In Procedures on Page 5).

19
Do’s and Don’ts
DO NOT: Install or operate this stove before reading this manual.
DO NOT: Close the draft beyond the point at which the flames are completely extinguished.
DO NOT: Open the stove door without fully opening the draft first.
DO NOT: Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in
salt water on the way to the mill. (This will void your warranty).
DO NOT: Handle the Nickel or Gold faceplate unnecessarily. Use the door handle only.
DO NOT: Force oversized logs into the firebox as this may dislodge the baffle assembly.
DO NOT: Close the door tightly during Burn-In Period.
DO: Be sure to clean any fingerprints from the Gold or Nickel faceplate before burning the stove. Clean the Gold or Nickel door
only with a household type glass cleaner and a very soft cloth.
DO: Consult local building department if other than recommended clearances are desired.
DO: Read instructions for the brick baffles occasionally to ensure you have not bumped or moved them out of place when loading
wood.
DO: Check the chimney and baffle a minimum of every 3 months to make sure they are clean.
DO: Burn seasoned, dry wood only! (RAIN = WET WOOD)
DO: Complete and return your warranty card.
DO: Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.
DO: Enjoy the warm feeling of your new Country™ Collection stove.

20
BLOWER PARTS
Cat. No. Description
H5658 Fan Blade (FSB700)
H5657 Fan Cage (FSB700)
H5660 Blower Power Cord (FSB700)
H5656 Speed Control (FSB700)
BRICKS, BLANKET AND GASKETS
H5642 Firebrick (replacement - specify size)
H3098 Firebrick Letter A - 3-7/8” x 8-3/4” (4 per stove)
H5589 Firebrick Letter B - 6-1/2” x 4-1/2” (4 per stove)
H5614 Firebrick Letter C - 3-1/2” x 9” (2 per stove)
H3099 Firebrick Letter D - 1-1/2” x 4-1/4” (2 per stove)
H3100 Firebrick Letter E - 3-7/8” x 9” (2 per stove)
H5612 Firebrick Letter F - 4-1/2” x 9” (22 per stove)
H5605 Firebrick Letter G - 3” x 9” (2 per stove)
H5581 Firebrick Letter H - 3-1/2” x 4-1/2” (1 per stove)
H5587 Firebrick Letter J - 4-1/2” x 7” (4 per stove)
H5586 Firebrick Letter K - 3” x 7” (2 per stove)
H5594 Firebrick Letter M - 4-1/2” x 4-1/2” (1 per stove)
H5585 Complete Baffle Brick Set
H5584 “Complete Cut Brick Set (Only need 4-1/2” x 9” bricks to finish)
H5583 Complete Brick Set
H5634 Ceramic Blankets (2 - 17” x 13” x 1”)
H5640 Glass Gasket 6 feet needed (per foot)
H5639 Door Rope 7/8” 6 feet needed (per foot)
FACEPLATES
71082 Traditional / Black
71083 Traditional / Gold
71084 Traditional / Nickel
71149 Traditional / Brushed Gold
71146 Traditional / Brushed Nickel
GLASS
71099 Plain
71096 Diamond
71100 Sailboat
71095 Cattail
71097 Evergreen
71098 Floral
HANDLES
H5654 Spring Handle / Nickel
H5653 Spring Handle / Gold
LEG PARTS
70003 Single Black Cascade Steel Legs (4 per pkg.)
70000 Single Black Olympic Cast Legs (4 per pkg.)
70001 Single Gold Olympic Cast Legs (4 per pkg.)
70002 Single Nickel Olympic Cast Legs (4 per pkg.)
70007 Single Brushed Gold Olympic Cast Legs (4 per pkg.)
70008 Single Brushed Nickel Olympic Cast Legs (4 per pkg.)
H5649 Heat Shield / Leg Hardware Bolt Kit
METAL COMPONENTS
H5561 Door Back and Handle (door gasket included)
H5629 Upper Hinge Pin
H5628 Lower Hinge Pin
H5626 Upper Hinge Pin E-Clip
H5577 Set of 6 screws and 6 washers for door assembly
H5566 Complete Stainless Secondary Burn Setup (includes
tubes and all mounting hardware)
H5626 Removable Inner Flue Collar Ring
NAMEPLATES
H5573 Gold w/ Rivets
H5572 Nickel w/ Rivets
H5643 Rivets for Nameplates (2 per)
OUTSIDE AIR KIT REPLACEMENT PARTS - LEG
H5516 15” of 4’ Aluminum Flex Tubing
(per foot - 1.25’ needed)
H5662 Leg Kit Plenum Box
OUTSIDE AIR KIT REPLACEMENT PARTS - PEDESTAL
H5516 15” of 4’ Aluminum Flex Tubing
(per foot - 1.25’ needed)
H5565 6” x 6-1/2” Rodent Screen
H5514 Rear Block Off Plate w/ Hole
PEDESTAL PARTS
H5556 Ash Drawer for Pedestal Large
H5661 Cast Iron Ash Plug
H5564 Ash Plug Remover and Rake
H5582 1/2 Cut Brick for Ash Removal
MISC. PARTS
H5650 Draft Rod Knob
71052 Dry Graphite (Apply to door handle and door hinges)
H5633 Anti-Seize 2 gram pouch
71134 Pipe Reducer from 8” to 6” Stainless
(MF) Add cat. no. for power cord (done 5-6-08)
Replacement Parts - Model ST310
Contact an Authorized Lennox Hearth Products dealer to obtain
any of these parts. Never use substitute materials. Use of
non-approved parts can result in poor performance and safety
hazards.