Contura C 586W User manual

Installation
instruction
C 586W
www.contura.eu

GB
38 CERTIFICATE
Manufacturer’s assurance
The stove is approved by the Swedish National Testing and Research Institute, SP SITAC and
fulfils the applicable rules for CE marking. Manufacture of the product has taken place in ac-
cordance with those documents that are the basis for the relevant type approval certification and
the required manufacturing checks.
378 001
N
O
R
D
I
C
E
C
O
L
A
B
E
L
378 001
N
O
R
D
I
C
E
C
O
L
A
B
E
L
Contura 586W is a Swan marked wood burning stove.
NIBE was the first stove manufacturer in Sweden to commit to Swan marking stoves. The Swan
mark is one aspect of our vision to be a company of the future, setting high quality standards
regarding the environment. Certification number 378-001.
EC Declaration of
conformity
MANUFACTURER
Name NIBE AB/Contura
Address Box 134, Skulptörvägen 10, SE-285 23 Markaryd
Place of manufacture Markaryd, Sweden
PRODUCT
Product type Stove fired by solid fuel
Type designation Contura
Standard SS-EN 13240
Intended for use Heating of living accomodation
Fuels Wood logs
Special conditions None
CE-MARKING 586W
Issued 2010
Nominal output 5 kW
Fuel type Wood logs
Flue gas temperature 290° C
Energy efficiency 79%
Emission of CO 0,06%
Appendix
Lighting and installation instructions
Niklas Gunnarsson
Business area manager NIBE STOVES

GB
39
Table of contents
Technical details 40
Prior to installation 40
Connection to chimney 42
Installation distances 43
Supply of combustion air 43
Assembly the stove 44
A warm welcome to Contura.
A warm welcome to the Contura family. We hope
you will get a great deal of pleasure from your new
stove. As a new owner of a Contura stove you have
secured a product with timeless design and long
service life. Contura also has combustion that is both
environmentally friendly and efficient for the best heat
production.
Read through these installation instructions carefully
before installation. Read how to best light your stove
in the lighting instructions.
CONTENTS
The stove becomes very hot
During operation, certain surfaces of the stove become
very hot and can cause burn injury if touched. Be aware of
the strong heat radiated through the hatch glass. Placing
flammable material closer than the safe distance indicated
may cause a fire. Pyre lighting can cause quick gas ignition
with the risk of damage to property and personal
injury.
NOTE! WARNING!
Report the installation of a stove to your
local authority.
The owner of the house is personally responsible for en-
suring compliance with the mandatory safety require-
ments and must have the installation approved by a
qualified inspector. Your local chimney sweep must also
be informed about the installation as this will affect the
routines for regular chimney-sweeping services.

GB
40
Installation by authorised
technician
This manual contains instructions about
how the stoves must be assembled and
installed. To ensure the function and sa-
fety of the stove, we recommend that the
installation is carried out by an authorised
technician. Contact one of our dealers who
can recommend suitable technicians.
Building application
These main instructions may give guidance
which would contravene national building
regulations. Please refer to supplementary
instructions or ask your local authority for
advice regarding building regulations.
Before installing a stove or erecting a
chimney it is necessary for you to make
a building application permission to your
local authority.
Structural support
Check that the wood joists are strong
enough to bear the weight of the stove and
chimney. The stove and chimney can usu-
ally be placed on a normal wooden joist in a
single occupancy house if the total weight
does not exceed 400 kg.
Hearth plate
Due to the risk of falling embers, a flam-
mable floor must be protected by a hearth
plate. It must extend 300 mm in front of
the stove and 100 mm on each side of the
stove, or have a 200 mm extension on each
side of the opening. The hearth plate can
consist of natural stone, concrete, metal
plate or glass. A painted metal or glass
hearth plate is available as an accessory
for these models.
Important to remember!
FACTS / PRIOR TO INSTALLATION
Prior to installation
1
2
3
4
Technical details
Output 3 – 7 kW
Nominal output 5 kW (approx. 1.5 kg wood/
hour)
Efficiency, up to 79%
Connector ext. Ø150 mm
Weight 100 kg
Width 500 mm
Depth 440 mm
Height 740 mm
Type approved in accordance with:
European standard EN-13240 class 1
Swedish environmental and quality marking, P-
marking cert. no. 22 03 09
Swedish type approved, cert.no. 0222/03
Norwegian standard NS 3059, Cert. No. 043-140
German standard DIN 18.891, RO-91 03 529
Danish standard DS/EN 13240 plus, id no. 598
If the insert needs bedding down to
be moved or if the pillar foot is to be
installed, remove any loose components.
When the stove is installed reinstall the
components in reverse order.
1 Fire bars
2 Grate disc
3 Heat deflector
4 Hearth cladding

GB
41
REMOVAL
2
1
How to remove the heat deflector
How to remove the hearth surround
3
4
Handle the hearth surround with care. Lift the smoke baffle with one hand
whilst removing the four side parts. Reinstall in reverse order.
1
2

GB
42
Connection to chimney
• Thestovemeetstherequirementsforconnectingtochimneys
dimensioned for 350°C flue gas temperature.
• Theexternaldiameteroftheconnectionsleeveis150mm.
• Thestoverequiresadraftinthechimneyofatleast–12Pa.The
draft is affected both by the length and area of the chimney, and
by how well sealed it is. Minimum recommended chimney length is
3,5 m and a suitable cross section area is 150-200 cm² (140-160
mm in diameter).
• Afluewithsharpbendsandhorizontalroutingreducesthe
draughtinthechimney.Maximumhorizontalflueis1m,onthe
condition that the vertical flue length is at least 5 m.
• Itmustbepossibletosweepthefulllengthoftheflueandthe
soot hatches must be easily accessible.
• Carefullycheckthatthechimneyissealedandthatthereisno
leakage around soot hatches and flue connections.
Rear connection to a masonry chimney
The back panel must be installed before the stove is rear connected.
Ø ca 180 mm
Ø ca 180 mm
2 31
5 64
CHIMNEY

GB
43
Check that the installation distances in the figures are maintained. When top connecting a steel flue please refer to
the relevant manufacturer’s installation instructions.
Observe the safety distances to combustible material that steel flues require.
The minimum distance in front of the stove opening to combustible parts of the building or interior decoration must
be at least 1 m.
750
500
155
455
16
150
250
350
450
50
150
250
350
Combustible wall Fire-retardant wall of
brick or concrete
712min 300 min 1000
496
Combustible roof
320
70
155
16
454
700
1100
Fire-retardant wall of
brick or concrete
88
552
47
Air inlet Ø67
Ø150
Indirect air supply through the external wall.
Supply of combustion air
Combustion air can be supplied via a duct from outside, or indi-
rectly via a vent in the outer wall of the room where the stove
is to be placed. The amount of combustion air that is used for
combustion is approx. 25m³/h.
HK
C 586W
Installation distances
INSTALLATION DISTANCES / SUPPLY AIR

GB
44
Place the back plate opposite the connector. Check that the
back plate is vertical and mark the mounting holes you wish
to use. Select holes so that it is as far away from any joints
as possible. Pre-drill the hole using an 8mm concrete drill;
the hole must be at least 80 mm deep. Clean the hole care-
fully and screw the back plate to the chimney breast using
the 4 supplied concrete screws. Screws that do not tighten
must be considered useless and be moved to new holes.
Insert the connection pipe into the wall connector
towards the folded tabs.
Ø 8 mm
50 mm
Check that the pipe protrudes 50 mm from the back plate and caulk between
the connection pipe and the connector in the wall using caulking rope. If
further sealing material is required, heat-resistant sealant may be used
Assembling the stove
ASSEMBLY

GB
45
Install the suspension brackets on the
stove body using 2 screws.
Detach the stove body from the
leg by unscrewing the 4 screws.
Lift the stove body from the leg and suspend the
brackets on the body above the back plate’s upper
mounting angle.
ASSEMBLY

GB
46
Lyft ut nederkanten av insatsen så att insatsen är lodrät. För in
insatsen mot ryggplåten så att kaminstosen skjuts in i anslut-
ningsröret.
Lås fast insatsen med 2 skruvar i ovankant.
Kontrollera att insatsen hänger lodrätt. Vid behov kan insatsen
justeras framåt i nederkant med hjälp av två justerskruvar i
nederkant.
Lås fast insatsen med 2 skruvar i nederkant.
ASSEMBLY
Final inspection of the installation
It is extremely important that the installation is inspected by an authorised chimney sweep before
the stove is used. Also read the ”Lighting instructions”, before lighting for the first time.

GB
47
Hook the side plate into the back plate and turn the front
edge in towards the stove body.
2
1
2
Secure the side panel at the front edge using a screw
at the upper edge and a screw at the lower edge.
Place the type plates with production number and installation
distances on the under side of the protective plate. Then screw
the protective plate securely into place with the plates turned
downwards.
Assembling the stove top
Lay the soap stone top (or Steel top, cast iron top) in place,
remember to handle with care. Finish by placing the hot air
grille and cover on the soap stone top.
ASSEMBLY

811144 IAV SE-EX C586W-3
2014-01-09
NIBE AB · Box 134 · 285 23 Markaryd · Sweden
www.contura.eu
Contura reserves the right to change colours, materials,
dimensions and models at any time without special notice.
Your dealer can give you the most up to date information.
Stoves shown in brochures may have optional extras.