Lenovo 20SE User manual

ThinkPad 11e Yoga Gen 6
Hardware Maintenance Manual

Note: Before using this information and the product it supports, be sure to read the general information
under ppendix “Notices” on page 83.
Third Edition (July 2022)
© Copyright Lenovo 2020, 2022.
LIMITED ND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services dministration
“GS ” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

Contents
About thi manual . . . . . . . . . . . . iii
Chapter 1. Safety information . . . . . . 1
General safety . . . . . . . . . . . . . . . . 1
Electrical safety . . . . . . . . . . . . . . . . 1
Safety inspection guide . . . . . . . . . . . . . 3
Handling devices that are sensitive to electrostatic
discharge . . . . . . . . . . . . . . . . . . 3
Grounding requirements . . . . . . . . . . . . 4
Safety notices (multilingual translations) . . . . . . 4
Chapter 2. Important ervice
information . . . . . . . . . . . . . . . 21
Strategy for replacing FRUs . . . . . . . . . . 21
Strategy for replacing a hard disk drive or a
solid-state drive . . . . . . . . . . . . . 21
Important notice for replacing a system
board . . . . . . . . . . . . . . . . . 22
How to use error codes . . . . . . . . . . 22
Strategy for replacing FRUs for CTO, special-bid,
and standard models. . . . . . . . . . . . . 22
Product definition . . . . . . . . . . . . 22
FRU identification . . . . . . . . . . . . 23
Chapter 3. General checkout . . . . . 25
What to do first . . . . . . . . . . . . . . . 25
Checkout guide . . . . . . . . . . . . . . . 26
Diagnosing problems . . . . . . . . . . . 26
Quick test programs . . . . . . . . . . . 26
UEFI diagnostic program . . . . . . . . . 27
Bootable diagnostic programs . . . . . . . 27
Power system checkout . . . . . . . . . . . 28
Checking the ac power adapter . . . . . . . 28
Checking the built-in battery and operational
charging . . . . . . . . . . . . . . . . 29
Checking the coin-cell battery . . . . . . . 29
Chapter 4. Related ervice
information . . . . . . . . . . . . . . . 31
Reset or restore Windows . . . . . . . . . . . 31
Passwords. . . . . . . . . . . . . . . . . 31
Power-on password . . . . . . . . . . . 31
Hard disk password . . . . . . . . . . . 31
Supervisor password . . . . . . . . . . . 32
System management password. . . . . . . 32
How to remove the power-on password . . . 33
How to remove the hard disk password. . . . 33
How to remove the system management
password . . . . . . . . . . . . . . . 34
Power management . . . . . . . . . . . . . 34
Sleep mode . . . . . . . . . . . . . . 34
Hibernation mode . . . . . . . . . . . . 35
Symptom-to-FRU index . . . . . . . . . . . 35
Numeric error codes . . . . . . . . . . . 36
Error messages . . . . . . . . . . . . . 37
Beep errors. . . . . . . . . . . . . . . 38
No-beep symptoms . . . . . . . . . . . 40
LCD-related symptoms . . . . . . . . . . 40
Intermittent problems . . . . . . . . . . . 41
Undetermined problems . . . . . . . . . 41
Chapter 5. Special key . . . . . . . . 43
Chapter 6. Location . . . . . . . . . 45
Locating computer controls, connectors, and
indicators . . . . . . . . . . . . . . . . . 45
Front . . . . . . . . . . . . . . . . . 45
Base . . . . . . . . . . . . . . . . . 45
Left . . . . . . . . . . . . . . . . . . 46
Right . . . . . . . . . . . . . . . . . 46
Bottom . . . . . . . . . . . . . . . . 47
Locating FRUs and CRUs . . . . . . . . . . . 47
Major FRUs and CRUs . . . . . . . . . . 49
LCD FRUs . . . . . . . . . . . . . . . 51
Miscellaneous parts . . . . . . . . . . . 52
Connector and cable guide . . . . . . . . 52
Looking up FRU information . . . . . . . . . . 54
Chapter 7. FRU replacement
notice . . . . . . . . . . . . . . . . . 55
Service tool kit . . . . . . . . . . . . . . . 55
Screw notices . . . . . . . . . . . . . . . 55
Retaining serial numbers . . . . . . . . . . . 56
Restoring the serial number of the system
unit . . . . . . . . . . . . . . . . . . 56
Retaining the UUID. . . . . . . . . . . . 57
Chapter 8. Removing or replacing a
FRU. . . . . . . . . . . . . . . . . . . 59
General guidelines. . . . . . . . . . . . . . 59
Before servicing the computer . . . . . . . . . 60
Disabling the built-in battery . . . . . . . . 60
1010 ThinkPad Pen Pro (for selected models) . . . 60
1020 Base cover assembly . . . . . . . . . . 61
1030 Keyboard . . . . . . . . . . . . . . . 63
1040 Pen charger with cable . . . . . . . . . . 64
1050 Speaker assembly . . . . . . . . . . . 65
© Copyright Lenovo 2020, 2022 i

1060 Wireless L N card . . . . . . . . . . . 65
1070 Coin-cell battery . . . . . . . . . . . . 66
1080 M.2 solid-state drive. . . . . . . . . . . 67
1090 Built-in battery . . . . . . . . . . . . . 68
1110 Heatsink . . . . . . . . . . . . . . . 69
1120 Power card and power card cable . . . . . 70
1130 Touchpad and touchpad cable. . . . . . . 72
1140 System board . . . . . . . . . . . . . 73
1150 World-Facing camera (for selected
models) . . . . . . . . . . . . . . . . . . 75
1160 LCD unit . . . . . . . . . . . . . . . 75
1170 Keyboard bezel assembly . . . . . . . . 76
2010 LCD strip cover. . . . . . . . . . . . . 77
2020 LCD panel. . . . . . . . . . . . . . . 77
2030 LCD hinges . . . . . . . . . . . . . . 78
2040 Conventional camera . . . . . . . . . . 78
2050 Camera and sensor board cable . . . . . . 79
2060 Wireless L N antenna assembly . . . . . . 79
2070 LCD cover assembly. . . . . . . . . . . 81
Appendix A. Notice . . . . . . . . . . 83
Appendix B. Abbreviation and
acronym table . . . . . . . . . . . . . 85
ii ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

About thi manual
This manual contains service and reference information for the following ThinkPad® product:
ThinkPad 11e Yoga Gen 6 Machine types (MT) 20SE and 20SF
Use this manual along with the advanced diagnostic tests to troubleshoot problems.
Important:
This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use
this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
Before servicing a ThinkPad product, be sure to read all the information under Chapter 1 “Safety
information” on page 1 and Chapter 2 “Important service information” on page 21.
© Copyright Lenovo 2020, 2022 iii

iv ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

Chapter 1. Safety information
This chapter presents the following safety information that you need to be familiar with before you service a
ThinkPad notebook computer.
• “General safety” on page 1
• “Electrical safety” on page 1
• “Safety inspection guide” on page 3
• “Handling devices that are sensitive to electrostatic discharge” on page 3
• “Grounding requirements” on page 4
• “Safety notices (multilingual translations)” on page 4
General afety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Ensure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, ensure that other service technicians and the customer's personnel are not
in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal
objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• fter service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
Electrical afety
Observe the following rules when working on electrical equipment.
© Copyright Lenovo 2020, 2022 1

Important:
• Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
• Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges (ESD). Do not use this type of mat to protect yourself from electrical
shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you. That person must be there
to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
CAUTION:
An electrical hock can occur only when there i a complete circuit. By ob erving the above rule,
you may prevent a current from pa ing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages. Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring high
voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• lways look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Units similar to those listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
2ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

Safety in pection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. s each
machine was designed and built, required safety items were installed to protect users and service
technicians from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-ThinkPad features or options not covered by this
inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the
beginning of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the authorized type specified for your computer. Go to: https://
support.lenovo.com/partslookup.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any non-
ThinkPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered
with.
Handling device that are en itive to electro tatic di charge
ny computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Note :
1. Use product-specific ESD procedures when they exceed the requirements noted here.
Chapter 1.Safety information 3

2. Ensure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• void contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– ttach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirement
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notice (multilingual tran lation )
The safety notices in this section are provided in the following languages:
• English
• rabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese
DANGER
4ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

DANGER
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1.Safety information 5

DANGER
6ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

PERIGO
Chapter 1.Safety information 7

PERIGO
PERIGO
PERIGO
PERIGO
8ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

PERIGO
PERIGO
PERIGO
DANGER
DANGER
Chapter 1.Safety information 9

DANGER
DANGER
DANGER
DANGER
DANGER
10 ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

DANGER
VORSICHT
VORSICHT
VORSICHT
VORSICHT
Chapter 1.Safety information 11

VORSICHT
VORSICHT
VORSICHT
VORSICHT
12 ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual

Chapter 1.Safety information 13

14 ThinkPad 11e Yoga Gen 6 Hardware Maintenance Manual