Leviton Leo led fresnel lfd10 User manual

LEO™ LED Fresnel

Cat. No. LFD10

User’s Guide

LEO™

P1

CATALOG LOGIC

LFD10-30B; LFD10-50B

Fixture Wattage Color Temperature Housing

LFD: LED Fresnel 10: 100W -30: 3200K B: Black Housing

-50: 5600K

SPECIFICATIONS

CAT. NO. LFD10

WATTAGE 100W

STANDBY LOAD

BEAM ANGLE 11° - 53°

WEIGHT 12.1 lbs. (5.5 kg)

SIZE W 10.1" (257mm) x H 15.2" (385mm) x D 14.6" (370mm)

ELECTRICAL 100-240 VAC, 50/60Hz

WARNINGS AND CAUTIONS

• TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that

power is off before installation.

• TO AVOID SERIOUS PERSONAL INJURY, always connect this product to a grounded circuit.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

SAFETY NOTES

WARNING: TO AVOID DEATH, SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE:

• Do not open the housing or attempt any repairs. In the unlikely event the unit may require service

please contact Leviton Technical Support. Opening the housing or attempting to repair product will

void the warranty.

• Do not expose this product to rain or moisture. This product is for indoor use only! (IP20) When

transferring product from extreme temperature environments, (e.g., cold truck to warm humid

ballroom) condensation may form on the internal electronics of the product. To avoid causing a

failure, allow product to fully acclimate to the surrounding environment before connecting it to power.

• Do not operate this product if you see damage on the housing, lenses, or cables.

P2

GETTING STARTED

Thank you for choosing LEO™ LED Fresnel by Leviton®. Every LEO™ LED Fresnel has been thoroughly

tested and has been shipped in perfect operating condition. Your LEO™ LED Fresnel should include:

Important: Unpack the product and check the box to make sure all the parts are in the package and

are in good condition. If any of them are damaged, please contact the shipper to make a claim. If any

components are missing, please contact our Customer Service Department at 1-800-736-6682.

• Fixture

• powerCON®B connector

• Fuse, glass tube, 3A (for 110V)

• Fuse, glass tube, 1.5A (for 220V)

• Metal Color Frame 7.5" x 7.5" (190 x 190mm)

• Safety Guard 7.5" x 7.5" (190 x 190mm)

• Safety Cable, 31.5" (800mm) with Spring Clips

• User’s Guide

• 36"-39.5" (1m) power lead with powerCON®& PBG NEMA 5-15P Connector

Power cords with alternate connectors, and powerCON®extension cables are available.

Please contact Leviton and review product data sheets for details.

P3

PRODUCT INTRODUCTION

LEO™ LED Fresnel is a high-performance Fresnel-style LED lighting ﬁxture that delivers a beautiful ﬂat

even ﬁeld of light in a choice of color temperatures (3200K and 5600K) with high color rendering index

(CRI 90+). The ﬁxture is fully dimmable from 0% to 100% and can be controlled manually or via DMX

controller. It also supports power linking with built-in powerCON®connectors. Virtually quiet operation

makes it ideal for use in any situation. The ﬁxture is RDM-ready for precise monitoring of the LED chip’s

performance and status to make maintenance easy.

IDENTIFY THE PARTS

Rear View

12 mm Hole

mounting yoke

Back panel Handle

Power in

& loop out

DMX input

(XLR5-pin male) Focusing Knob

Barndoor clip

Fuse

DMX output

(XLR5-pin female)

Power switch

Status

indication

lamps

4-Digit display

3 Operation

buttons

Manual

dimming knob

Barn door

clip

Fresnel

Lens

Lens clips

Front View

3-Slot

accesory

runners

Control panel

Reset button

P4

SAFETY NOTES

• This product contains no user-serviceable parts. Do not open the housing or attempt any repairs,

doing so will void the manufactures warranty. In the unlikely event the unit may require service please

contact Leviton technical support.

• Do not operate this product if you see damage on the housing, lenses, or cables.

• This product is for indoor use only! (IP20) To prevent risk of ﬁre or shock, do not expose this product to

rain or moisture. When transferring product from extreme temperature environments, (e.g. cold truck

to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid

causing a failure, allow product to fully acclimate to the surrounding environment before connecting

it to power.

REPLACE FUSE

CAUTION:

Fuse pre-installed in BLACK fuse cover supports 220V AC Power only.

Fuse pre-installed in GREY fuse cover supports 110V AC Power only.

Always make sure you are connecting this product to the proper voltage in accordance

with the speciﬁcations in this manual or on the product’s speciﬁcation label.

Choose the correct fuse for your power voltage before connecting power.

Step 1: Unplug the product from power.

Step 2: Use a slotted screwdriver, push slightly and rotate counterclockwise to open the fuse cap.

Step 3: Take out the fuse cap and fuse. Put a new fuse inside the fuse cap.

Step 4: Screw the fuse cap back in place and reconnect power.

FUSE 110V/3A; 220V/1.5A

SLOW BLOW

OPEN LOCK

P5

CONNECT POWER

CAUTION:

LEO™ LED Fresnel comes with a power lead terminated with a powerCON®A connector on one side,

and a PBG NEMA5-15P connector on the other side. Other connector options are available from Leviton

or may be installed by your contractor. In addition, the ﬁxture is designed for "Feed-Thru" operation using

single power source connection at the ﬁrst ﬁxture, then, using powerCON®extensions between ﬁxtures.

The maximum load supported is 16A through the powerCON®connectors which is reduced to 15A if you

use a 15A source power connector like a NEMA 5-15P.

If creating your own powerCON®connectors, use the table below to wire the included powerCON®

B connector, or a local plug to the power lead.

Connection Wire

AC Live Brown

AC Neutral Blue

AC Ground Green / Yellow

CONNECT DMX

LEO™ LED Fresnel uses 5-pin XLR connectors for signal transmission and can be controlled via

DMX-512 protocol. The diagram below shows the ﬁxture’s XLR-5 signal ports.

Step 1: Connectthe(male)5-pinconnectorsideoftheDMXcabletotheoutput(female)5-pinconnector

of the DMX console.

Step 2: Connecttheendofthecablecomingfromtheconsolewhichwillhavea(female)5-pinconnector

to the ﬁxture’s input port ("DMX IN") consisting of a (male) 5-pin connector.

Step 3: Then, proceed to connect from the output port ("LOOP") as stated above to the input of the

following ﬁxture and so on.

XLR Pin # Signal

1 common

2 data -

3 data +

4 NC

5 NC

1

2

3

4

5

4

3

2

1

DMX IN LOOP

XLR-5 signal ports

WARNING: TO AVOID SERIOUS PERSONAL INJURY, always connect this product to

a grounded circuit.

P6

MOUNT FIXTURE

CAUTION:

LEO™ LED Fresnel may be mounted in any position (max. tilting +45° to -90° from horizontal); however,

make sure there is adequate room for ventilation, conﬁguration, and maintenance.

The ﬁxture comes with a hanging/mounting yoke to which you can attach mounting clamps. The bracket

has a 0.5" (12mm) hole, which is appropriate for this purpose. Make sure the clamps are capable of

supporting the weight of this product.

FIXTURE ANGLE ADJUSTMENT

The ﬁxture can be tilted up and down to position the light where it is needed.

Step 1:

Loosen the yoke fastening knob, use the handle on the rear of the unit to keep the ﬁxture steady.

Step 2: With the ﬁxture turned on, use the handle to tilt it to the desired angle.

Step 3: Tighten the yoke fastening knob.

FIELD ANGLE ADJUSTMENT

You can adjust the ﬁeld angle of the ﬁxture with the focusing knob on the rear of the unit.

To reduce the ﬁeld angle (SPOT), turn the focus dial clockwise.

To enlarge the ﬁeld angle (FLOOD), turn the focus dial counterclockwise.

Always mount this product in a safe position with adequate ventilation and away from

a heat source, at least 20" (50 cm) from adjacent surface, and no ﬂammable materials

close by the product while it is operating, at least 8" (20 cm) from adjacent surfaces.

AlwaysconnecttheprovidedSafetyCableto the ﬁxture anda suitableanchor.Thesafety

cable should loop through the ﬁxture yoke and be connected to a secure attachment at

the other end.

ACCESSORIES

LEO™ LED Fresnel can accommodate many different accessories.

ACCESSORY SLOTS

CAUTION:

LEO™ LED Fresnel has 3 accessory slots in the front of the ﬁxture and is equipped with a spring-loaded

barn door clip that prevents color frames and accessories from falling out.

Step 1: Release the barn door clip by pushing it sideways while gently pulling backwards

Step 2: Insert the media/accessories, secure with a safety cable where necessary.

Step 3: Lock the barn door clip by pushing sideways while gently pushing forward.

P7

Accessories such as barn doors and color scrollers must be secured by a safety cable

to the mounting structure.

Make sure all color / diffusion media are locked in position with the barn door clip before

hanging the ﬁxture.

Cat. No. Description Part Number

All Safety Cable (included) TA0SC-000

LFD10 8 Leaf Barn Door 7.5" x 7.5" (190 x 190mm) LFD10-BDB

LFD10 Metal Color Frame 7.5" x 7.5" (190 x 190mm) (included) LFD10-CFB

LFD10 Safety Guard 7.5" x 7.5" (190 x 190mm) (included) LFD10-SGB

P8

OPERATION

CAUTION:

LEO™ LED Fresnel will start a self-checking process when power is applied. The unit will display the

DMX address for dimming when ready to use. For standard operation, connect the ﬁxture to a power

source (100~240V AC single phase), and a DMX signal cable. The LED Display will turn on after the

power switch is turned to "ON" position. You are now ready to set the desired conﬁguration and DMX

addresses.

You can assign a DMX channel to control dimming, cooling fan speed, LED display-on time, built-in

effects and live/safe modes according to the DMX value on the "Menu Map". These parameters can also

be assigned through a console.

CONTROL INTERFACE

The ﬁxture comes with a 4-digit Display and 3 operation buttons on the side of the unit for control

settings:

OPERATION BUTTONS

DOWN Backward / downward change / query sequence change

UP Forward / upward change / query sequence change

ENTER Conﬁrm / mode switch / enter new data or setting

RESET Press to reset the ﬁxture, parameters remain unchanged

Do not touch this product’s housing during operation because it may be very hot if

overheated.

The maximum ambient temperature is 95˚F (35˚C). Do not operate this product at a

higher temperature.

Do not cover the ventilation holes when operating to avoid internal overheating.

Avoid direct eye exposure to the light source while the product is on.

In case of a serious operating problem, stop using this product immediately!

STATUS INDICATION LAMPS

PWR (Power) Light up when power is applied to the unit.

SYS (System) Indicates the status of the ﬁxture:

No lights when working properly,

Flashes when the ﬁxture light source detects overheating.

SIG (Signal) Light up when proper DMX signal is received,

Flashes when receiving wrong signals,

No lights when no signal is received.

CONTROL BASICS

CAUTION:

Connect power to the powerCON®connector at the rear side of LEO™ LED Fresnel and switch the power

switch to "ON" position. The 4-digit display will turn on and the ﬁxture is ready to operate. The ﬁxture is

defaulted for DMX control; press the 3 operation buttons to the desired operation mode.

DIMMING DMX CHANNEL

The ﬁxture can be controlled by a DMX channel, displayed by the 4-Digit display. The light output intensity

is based on the DMX channel value.

Note: LEO LED Fresnel requires only one DMX channel for dimming, and that is the minimum number of

DMX channels needed for the ﬁxture.

SHOWING DIMMING VALUE

The dimming value is displayed on the display for local monitoring.

MONITORING LED TEMPERATURE

Temperature of the LED light source is displayed.

P9

Check the fuse before connecting power.

P10

CONTROLLING COOLING FAN SPEED

The highest cooling fan speed can be remotely or locally controlled. The LFD10 is defaulted so that the

fan will start to operate in slowest speed when LED temperature is detected at 95°F (35°C) or above to

maintain the lowest fan noise.

(Note: cooling fan cannot be stopped; slowest speed is 60% of full speed)

4-DIGIT DISPLAY ON

The light-on time of the 4-Digit display can be set to 30 sec., 1 min., 2 min., 3 min. or continuously on.

RESETTING THE FIXTURE

The ﬁxture can be reset locally by pressing the RESET button on the unit or remotely by a DMX channel.

SETTING DIMMING STEPS

Two dimming steps, standard and ﬁne, are available for selection. It can be selected locally or remotely.

PRE-LOADED EFFECTS

The ﬁxture has pre-loaded eight effects for demonstration. It can be selected locally or remotely.

DIMMING MODES

Two dimming modes, DMX and manual control, are available for selection. It can be selected locally or

remotely.

SETTING SAFE OPERATION MODE

CAUTION:

At Safe mode, LEO™ LED Fresnel will limit the light output when the LED temperature rises above 149°F

(65°C) in order to protect the LED light source from overheating. The light output will be the ﬁrst priority

when Live Mode is selected.

"Live" mode allows the LED light source to operate at over-temp conditions which might

shorten the lifetime and even burn out the LED chip!

It is recommended to use the factory default "Safe" mode for normal operations.

P11

NUMBERS & CHARACTERS DISPLAYED

A,B,C,D,E,F NUMBER 0-9 H,L,N,O,P,Q,R,S,T,U

Note: The corresponding display number "5" and character "S" appear the same, please note the difference.

CONTROL ATTRIBUTES AND DEFAULT DISPLAYS AND SETTINGS

The LEO™ LED Fresnel ﬁxtures have several different control attributes. With the exception of the

dimming attribute which must be assigned a DMX value for remote control, all other attributes may be

manually set only at the ﬁxtures, or, remote controlled from your DMX console. Therefore, from a DMX

perspective, your ﬁxture may be a 1, 2, 3, 4, 5, 6, 7 or 8 channel ﬁxture depending on which attributes are

assigned to a channel. Some customers will assign a unique DMX address for each dimming attribute,

then, a common channel for all other attributes so ﬁxtures are always controlled together. The system is

ﬂexible so the speciﬁc conﬁguration is up to you.

The ﬁxture is factory-set to display the default DMX address "A001" until a new address is assigned.

Then, the last assigned DMX address will become the default display.

Please refer to the chart below to see all the default settings and displays:

CONTROL ATTRIBUTES

Menu Items Default

Display Value

Range Default

Value Options

DMX Value Level Remarks

Dimming address 1-512 1 0-255 Mandatory to assign DMX

channel to this attribute

Dimming mode 1/2 1 1

2

Dimming according to

DMX value

Dimming according to

manual knob

Dimming mode

control address 1-512 0 0-255

Operation mode 0/1 1 0-127

128-255

0

1

Live: Light output will be

the ﬁrst priority

Safe: LED over-temp

protection, light output will

be limited when temp. over

149°F (65°C)

Operation mode

control address 1-512 0 0-255

P12

Menu Items Default

Display Value

Range Default

Value Options

DMX Value Level Remarks

Built-in effects 0~8 0 0-20

21-40

41-70

71-100

101-130

131-160

161-190

191-220

221-255

0

1

2

3

4

5

6

7

8

Normal dimming

Flash effect 1 – super fast

Flash effect 2 – fast

Flash effect 3 – medium

Flash effect 4 – slow

Fade-in & fade-out effect 1

Fade-in & fade-out effect 2

Fade-in & fade-out effect 3

Fade-in & fade-out effect 4

Built-in effects

control address 1-512 0 0-255

Dimming steps 1/2 1 0-31

32-255 1

2Standard: 256 steps

Fine: 512 steps

Dimming steps

control address 1-512 0

Remote DMX reset 0/1 0 0-127

128-255 0

1At normal control

Trigger reset

Remote DMX reset

control address 1-512 0

LED display-on

time 1~5 1 0-50

51-100

101-150

151-200

201-255

1

2

3

4

5

Continuously on

LED display off after 30 seconds

LED display off after 1 minute

LED display off after 2 minutes

LED display off after 3 minutes

LED display-on time

control address

1-512 0 0-255

Fan speed 1~5 1 0-50

51-100

101-150

151-200

201-255

1

2

3

4

5

Auto

90% of full speed

80% of full speed

70% of full speed

60% of full speed

Fan speed

control address 1-512 0 0-255

LED temperature ˚C

˚F

0/1 0 Error: Below the

lowest limit < 32°F / 0.1°C

Error: Above

the highest limit > 212°F /

99.9°C

Dimming Value 0~255 0 0-255 Display in hex

Parameter

setting status Press "ENTER"

button for 5 seconds to

resume default settings.

DEFAULT SETTINGS

P13

Do not use ammonia-based or other harsh commercial cleaners. They may damage the

glass surface and the Anti-Reﬂective coatings.

Replace lenses if they contain visible damage (cracks or deep scratches).

MAINTENANCE

To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect

the product from power via breaker or by unplugging it.

EXPECTED LED LIFESPAN

LEDs gradually decline in brightness over time, mostly because of heat. Packaged in clusters, LEDs

exhibit higher operating temperatures than in ideal, single-LED conditions. For this reason, using

clustered LEDs at their fullest intensity signiﬁcantly reduces the LED's lifespan. Under normal conditions,

this lifespan can be 50,000 hours at 77 °F (25 °C). If extending this lifespan is vital, lower the operating

temperature by improving the ventilation around the product and reducing the ambient temperature to an

optimal operating range. In addition, limiting the overall projection intensity may also help to extend the

LED's lifespan.

LENS

The lens in your ﬁxture is made of a high quality glass and reﬂective coating which should require little

maintenance.However,due tofog residue,smoke anddust, lenscleaning mustbe carried out periodically

to optimize light output. To maintain optimum performance and minimize wear, clean this product at least

twice a month. However, usage and environmental conditions contribute to increased cleaning frequency.

CAUTION:

Step 1: Unplug the product from power and wait until the product is at room temperature.

Step 2: Remove dust with a blast of oil-free air or wipe with a clean, lint-free cloth. Isopropyl alcohol

may be used on the cloth.

Step 3: Make sure to dry all parts completely before plugging the product back in.

P14

WARRANTY INFORMATION

LEVITON LIGHTING & ENERGY SOLUTIONS DIVISION of Leviton manufacturing Co. Inc. warrants its

Entertainment Products to be free of material and workmanship defects for a period of two years after

system acceptance or 26 months after shipment, whichever comes ﬁrst. This Warranty is limited to repair

or replacement of defective equipment returned Freight Pre-Paid to Leviton Lighting & Energy Solutions

Division at 20497 Teton Ave., Tualatin, Oregon 97062, USA. User shall call 1-800-959-6004 and request

a return authorization number to mark on the outside of the returning carton, to assure that the returned

material will be properly received at Leviton. All equipment shipped back to Leviton must be carefully

and properly packed to avoid shipping damage. Replacements or repaired equipment will be returned to

sender freight prepaid, F.O.B. factory. Leviton is not responsible for removing or replacing equipment on

the job site, and will not honor charges for such work. Leviton will not be responsible for any loss of use

time or subsequent damages should any of the equipment fail during the warranty period, but agrees only

to repair or replace defective equipment returned to its plant in Tualatin, Oregon. This warranty is void

on any product that has been improperly installed, overloaded, short circuited, abused, or altered in any

manner. Neither the seller nor Leviton shall be liable for any injury, loss or damage, direct or consequential

arising out of the use of or inability to use the equipment. This Warranty does not cover lamps, ballasts,

and other equipment which is supplied or warranted directly to the user by their manufacturer. Leviton

makes no warranty as to the Fitness for Purpose or other implied Warranties.

TRADEMARK DISCLAIMER

Use herein of third party trademarks, service marks, trade names, brand names and/or product names

are for informational purposes only, are/may be the trademarks of their respective owners; such use is

not meant to imply afﬁliation, sponsorship, or endorsement.

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at

Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus

Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

Leo is a registered trademark of Leviton Mfg. Co., Inc. in the U.S.A.:

NOTES

__________________________________________________________________________________

P15

P16

NOTES

__________________________________________________________________________________

DI-000-LFD10-05A

LEVITON MANUFACTURING CO., INC.

LIGHTING & ENERGY SOLUTIONS DIVISION

20497 SW Teton Avenue. Tualatin, OR 97062

Telephone: 1-800-736-6682 FAX: 503-404-559

Tech Line (6:00 AM-4:00 PM P.S.T. Monday-Friday): 1-800-959-6004

Email: [email protected]

Leviton Manufacturing Co., Inc.

201 North Service Road, Melville, N.Y. 11747

Telephone: 1-800-323-8920 • FAX: 1-800-832-9538

Information and speciﬁcations are subject to change without notice.

DISCARD ANY OLDER VERSIONS OF THIS USER’S GUIDE AND REPLACE WITH THIS VERSION.

Visit Leviton’s Web site at http://www.leviton.com

LEO™

Leviton LEO LED Fresnel LFD10 User manual

Popular Dj Equipment manuals by other brands