Leviton EPCM1-OF3 User manual

PK-A3435-10-00-5A
Dual Mount Pedestal with
Automatic Cable Management
Installation Manual
Cat. Nos. EPCM1-OF3, EPCM2-OF3, EPCM3-OF3
For use with Cat. Nos. EV320, EV32W, EV48W, and EV48S
WEB VERSION

WEB VERSION

TABLE OF CONTENTS
1 Warnings ........................................................................................................................................4
2 Installation ......................................................................................................................................5
2.1 Making Drill Holes.............................................................................................................5
2.2 Anchoring ..........................................................................................................................6
2.3 Upper Part Installation......................................................................................................7
2.4 Cable Gland Installation ..................................................................................................9
2.5 Bracket Installation.........................................................................................................10
2.6 Connector Base Installation ..........................................................................................11
2.7 Mounting the Charging Station .....................................................................................12
2.8 Charger Holder Plate Installation ..................................................................................13
2.9 Connecting ......................................................................................................................14
2.10 Positioning the Cable Clamp .......................................................................................16
3 Standard Statements and Warranty ...........................................................................................17
WEB VERSION

1 WARNINGS
4
WARNING: TO AVOID INJURY, DEATH OR PROPERTY DAMAGE, follow these safety instructions.
Electrical hazard!
This installation manual is intended for qualified personnel only.The information and instructions in the
manual about selecting the location, installation and connection of the charging station must be adhered to.
Safety Instructions
Use of this manual
• The installation, commissioning and maintenance of the charging station must only be performed by
correctly trained, qualified and authorized personnel who are knowledgeable of and responsible for the
compliance with existing standards and installation regulations.
• If the specifications for the location are not followed, this can result in death, injury or equipment damage!
• The pedestal must always be fitted with two charging stations!
EPCM1-OF3: Quantity
Pedestal Body 1
M8 100mm Expansion Screw 4
M6 20mm Screw 14
M6 Spring Washer 14
M6 Flat Washer 14
M8 16mm Screw 16
M8 Flat Washer 6
M40 Cable Gland 2
M8 Spring Washer 6
M5 22mm Screw 10
Junction of Pedestal 1
Connector Base 2
Screwdriver 1
Installation Manual 1
EPCM2-OF3: Quantity
Mounting Template 1
EPCM3-OF3: Quantity
Cord Management
System 1
WEB VERSION

2 INSTALLATION
2.1 Making Drill Holes
1. Mark the 4 holes on the concrete foundation using the base-plate of the pedestal. Make sure that
the connection cable is located precisely underneath the opening in the base-plate.
2. Drill the 4 mounting holes:
Diameter: 10 mm.
Drill-hole minimum depth: 84 mm.
3. Hammer the anchors (not included) so that they are flush with the floor.
4. Thread the connection cables from the bottom through the pedestal upwards through
the cable opening.
5
11.0 in. (280.0mm)
6.1 in. (155.0 mm.)
4-Ø0.39 in. (Ø10.0 mm.)
WEB VERSION

2 INSTALLATION
2.2 Anchoring
1. Position the pedestal (lower part) directly over the cable outlet.
2. Anchor the pedestal (lower part) to the foundation using 4 sets of M8 100 mm. expansion screws
(flat washer, spring washer and bolt were included).
3. Remove the 4 M6 20 mm. screws of wiring window on pedestal.
6
WEB VERSION

2 INSTALLATION
2.3 Upper Part Installation
1. Connect the junction by 6 sets of M6x20 mm. screws with spring washer and flat washer.
2. Cap the upper part of pedestal with cable management structure.
7
WEB VERSION

2 INSTALLATION
2.3 Upper Part Installation (Continued)
3. Fix the upper part with 6 sets of M6 20mm screws with spring washer and flat washer.
8
WEB VERSION

2 INSTALLATION
2.4 Cable Gland Installation
1. Insert the 2 cable glands to the pedestal properly.
2. Fix 2 M8x16mm screws with 5 mm. thread length reserved for charger holder plate.
9
WEB VERSION

2 INSTALLATION
2.5 Bracket Installation
1. Take off the wall-mounted bracket of 2 chargers, and fix it in the corresponding position on the
charger holder plate with 8 of M8x16 mm. screws.
10
WEB VERSION