Leviton Smartlockpro gfnt2-din User manual

Installing and Testing

a DIN Rail Mount

GFCI Receptacle

Please read this leaﬂet

completely before getting started.

PK-A3094-10-00-0B

CAUTION

• To prevent severe shock or

electrocution always turn the power

OFF at the service panel before

working with wiring.

• Use this GFCI with copper or

copper-clad wire. Do not use it with

aluminum wire.

• Do not install this GFCI receptacle

on a circuit that powers life

support equipment because if the

GFCI trips it will shut down the

equipment.

• For installation in wet locations,

protect the GFCI receptacle with

a weatherproof enclosure that will

keep both the receptacle and

any plugs dry.

• Must be installed in accordance

with national and local electrical

codes.

1. What is a GFCI?

A GFCI receptacle is different from conventional

receptacles. In the event of a ground fault,

a GFCI will trip and quickly stop the ﬂow of

electricity to prevent serious injury.

Deﬁnition of a ground fault:

Instead of following its normal safe path,

electricity passes through a person's body to

reach the ground. For example, a defective

appliance can cause a ground fault.

A GFCI receptacle does NOT protect against

circuit overloads, short circuits, or shocks. For

example, you can still be shocked if you touch

bare wires while standing on a non-conducting

surface, such as a wood ﬂoor.

GFCI's contain a lockout feature that will prevent

RESET if:

• There is no power being supplied to the GFCI.

• The GFCI is miswired due to reversal of the

LINE and LOAD leads.

• The GFCI cannot pass its internal test,

indicating that it may not be able to provide

protection in the event of a ground fault.

GFNT1-DIN (with GFCI) features:

4. Should you install it?

Installing a GFNT1-DIN or GFNT2-DIN, with

GFCI receptacle, can be more complicated than

installing a conventional receptacle.

Make sure that you:

• Understand basic wiring principles and

techniques

• Can interpret wiring diagrams

• Have circuit wiring experience

• Are prepared to take a few minutes to test

your work, making sure that you have wired

the device (with GFCI) correctly

5. LINE vs. LOAD

A cable consists of 2 or 3 wires.

Cable Wires

LINE cable:

elivers power from the service panel (breaker

panel or fuse box) to the device. If there is only

one cable entering the electrical box/enclosure, it

is the LINE cable. This cable should be connected

to the device's LINE terminals only.

LOAD cable:

Delivers power from the device (with GFCI)

to another receptacle in the circuit. This cable

should be connected to the device's

LOAD terminals only.

6. Turn the power OFF

Plug an electrical device, such as a lamp or

radio, into the receptacle on which you are

working. Turn the lamp or radio ON. Then, go to

the service panel. Find the breaker or fuse that

protects that receptacle. Place the breaker in

the OFF position or completely remove the fuse.

The lamp or radio must turn OFF.

Next, plug in and turn ON the lamp or radio at

the receptacle's other outlet to make sure the

power is OFF at both outlets. If the power is

not OFF, stop work and call an electrician to

complete the installation.

TEST

RESET

FOLLOW INSTRUCTIONS

SUIVEZ INSTRUCTIONS

TEST MONTHLY

TEST MENSUEL

FRONT VIEW

GFCI

Receptacle

RESET

button:

See step 9

Green/Red

Status

Indicator

LED

TEST

button:

See step 9

Outlet

LINE

ABC

LOAD

Service

Panel

LOAD

LINE LINE

3. Compatible DIN Rail Conﬁgurations

The device mounts using two DIN clips attached to its back. It will properly mount

using any of the following DIN rail conﬁgurations:

DIN 35 Standard Rail

DIN 32 Standard Rail

DIN 35 Low Profile Rail

Compatible DIN Rail Configurations

Sample circuit:

Outlet

Line Terminals

Load Terminals

7. Placement in circuit

The GFCI's place in the circuit determines if it

protects other receptacles in the circuit.

Placing the GFCI in position A will also provide

protection to "load side" receptacles B and C.

On the other hand, placing the GFCI in position

C will not provide protection to receptacles A or

B. Remember that receptacles A, B, and C can

be in different rooms.

WEB VERSION

Connect the LINE cable wires to the device LINE terminals:

• The white wire connects to the Neutral (N) terminal.

• The black wire connects to the Line (L), or Hot terminal.

Connect the LOAD cable wires to the device LOAD terminals:

• The white wire connects to the Neutral (N) terminal.

• The black wire connects to the Line (L), or Hot terminal.

Connect the grounding wires (only if there is a grounding wire):

• Connect a bare copper (or GREEN) 10, 12 or 14 AWG wire to the grounding

terminal on the device. If the box/enclosure has a grounding terminal, also

connect a similar wire to the grounding terminal on the box/enclosure. Connect

the ends of these wires to the LINE or LOAD cable's bare copper (or GREEN)

wire using a wire connector. If these wires are already in place, check the

connections.

Complete the installation:

• Test your work. Go to step 9.

Connect the LINE cable wires to the device LINE terminals:

• The white wire connects to the Neutral (N) terminal.

• The black wire connects to the Line (L), or Hot terminal.

Connect the grounding wire (only if there is a grounding wire):

• For installations with no grounding terminal in enclosure (diagram not shown):

Connect the LINE cable's bare copper (or GREEN) wire directly to the grounding

terminal on the device.

• For installations with a grounding terminal in enclosure (diagram shown above):

Connect a bare copper (or GREEN) 10, 12 or 14 AWG wire to the grounding

terminal on the device. Also connect a similar wire to the grounding terminal on

the box/enclosure. Connect the ends of these wires to the LINE cable's bare

copper (or GREEN) wire using a wire connector. If these wires are already in

place, check the connections.

Complete the installation:

• Test your work. Go to step 9.

Wire

0.236" (6.0 mm)

About Wire Connections To Device:

Device Current (A) Voltage (V) AWG

GFNT1-DIN 15 125 14-10

GFNT2-DIN 20 125 12-10

About Wire Connections To Device:

Device Current (A) Voltage (V) AWG

GFNT1-DIN 15 125 14-10

GFNT2-DIN 20 125 12-10

Wire

0.236" (6.0 mm)

9. Test your work

Why perform this test?

• If you miswired the device with GFCI, it may not prevent personal injury or death due to a ground fault

(electrical shock).

• If you mistakenly connect the LINE wires to the LOAD terminals, the GFCI will not reset and will not provide

power to either the GFCI receptacle face or the LOAD terminals. The LED indicator light will be ON.

Procedure:

(a) This device (with GFCI) is shipped from the factory in the tripped condition and cannot be reset until

it is wired correctly and power is supplied to the device. Plug a lamp or radio into the GFCI (and leave

it plugged in). Turn the power ON at the service panel. Ensure that the GFCI is still in the tripped

condition by pressing the TEST button. If the lamp or radio is OFF, and the GFCI will not reset, go to the

Troubleshooting section as the Line and Load connections are reversed.

(b) Press the RESET button fully and release. If the Status Indicator Light turns Green and the lamp or

radio is ON, the GFCI has been installed correctly. If the Status Indicator Light turns or continuously

blinks Red, or the GFCI cannot be reset, go to the Self-Test Operation section.

one(s), in addition to the GFCI, lose power when you press the GFCI TEST button. Place a "GFCI

PROTECTED OUTLET" sticker on every receptacle that lost power, then press the RESET button to

reset the GFCI. DO NOT plug life saving devices into any of the receptacles that lost power.

(d) Press the TEST button (then RESET button) every month to assure proper operation. If the Status

Indicator Light does not turn Green when the RESET button is depressed and then released, or the

GFCI cannot be reset, it must be replaced.

SELF-TEST OPERATION

• A Self-Test GFCI receptacle has all the features of a conventional GFCI receptacle. In addition, this receptacle tests itself periodically to conﬁrm

the GFCI electronics are functional. The Status Indicator Light will be solid green when the GFCI is powered from Line side and working correctly.

• Self-Test Indications: If the Status Indicator Light is solid or ﬂashing RED a problem may exist. Press the TEST button to trip the GFCI. If unable

to Reset, replace the GFCI. NOTE: The status indicator may ﬂash Red at power "ON" and Reset.

RESET

TEST

RESET

TEST

RESET

TEST

RESET

TROUBLESHOOTING

Turn the power OFF and check the wire connections against the appropriate wiring diagram in step 8A or 8B. Make sure that there are no

loose wires or loose connections. If the Status Indicator Light is not ON and the device is unable to reset this could be a result of no power

available. Start the test from the beginning of step 9 if you rewired any connections to the GFCI.

PK-A3094-10-00-0B

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality

Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

SmartlockPro is a Trademark of Leviton Manufacturing Co., Inc. registered in the United States, Canada, Mexico and China.

Self Test Cat. No. Description

GFNT1-DIN 15A-125VAC, 60Hz DIN Rail Mount GFCI

GFNT2-DIN 20A-125VAC, 60Hz DIN Rail Mount GFCI

All devices rated 20A feed-through when using #12 or #10 AWG conductors

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired operation of the device.

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) 1 800 405-5320 (Canada Only) www.leviton.com

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship

under normal and proper use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.

com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed

improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with

any labels or instructions. There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose, but if any implied warranty

is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to two years. Leviton is

not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or

delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

This product is covered by U.S. Patent Nos. 6,040,967; 6,246,558; 6,282,070; 6,381,112; 6,437,953; 6,646,838; 6,657,834; 6,788,173; 6,864,766; 6,944,001; 7,336,458; 7,400,479;

7,463,124; 7,697,252; 7,737,809; 7,764,151; 7,907,371; 8,004,804; 8,054,595; 8,130,480; 8,547,126; 8,587,914; 8,599,522; 8,944,859 and corresponding foreign patents.