LEX Lighting LexLense 469 User manual

DMX Channels(slider) Value Function
Channel 1 0 - 4
5 - 255
No Effect
Selects Pattern Modes
Channel 2 0 - 255 Speed of Chases
Channel 3 0 - 4
5 - 255
No Effect
Strobe Fast - Slow
Channel 4,5,6,7,8,9,10 & 11
(Note: Channel 1 must be 0 for these
channels to have effect)
0 - 35
36 - 49
50 - 255
No Effect
Spread Effect
Static Effect
Channel 12
(Note: when channel 12 is greater
than 50, other channels will have no
effect)
0 - 49
50 - 91
92 - 133
134 - 175
176 - 255
No Effect
Red LED’s
Green LED’s
Blue LED’s
All LED’s
DMX Controller Channel Modes
Lex Lighting Safety Instructions
1. Please keep this User Manual for future reference and be sure to pass this manual on to
anyone using the xture.
2. Always make sure that you are connecting to the proper voltage as stated on the decal or rear
panel of the xture.
3. This product is intended for indoor use only! To prevent risk of re or shock, do not expose
xture to rain or moisture.
4. Make sure there are no ammable materials close to the unit while operating.
5. The unit must be installed in a location with adequate ventilation, atleast 20inches (50 cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
6. Always disconnect from power source before servicing or replacing fuse and be sure to
replace with same fuse rating.
7. Secure xture to fastening device using a safety chain.
8. Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate xture at temperatures
higher than this.
9. In the event of a serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction and will void your warranty. Please contact the nearest authorized technical
assistance center.
10. Never connect the device to a dimmer pack.
11. Make sure the power cord is never crimped or damaged.
12. Never disconnect the power cord by pulling or tugging on the cord.
13. Never carry the xture directly from the cord. Always use the hanging/mounting bracket.
14. Avoid direct eye exposure to the light source while it is on.

Congratulations on purchasing your new lighting effect
from Lexlighting. Reading through this manual will ensure
trouble free and long life operation of the unit.
Features:
- 469 High Brightness LED’s (Red, Green & Blue)
- Sound To Light (Inbuilt Microphone)
- Master/Slave Mode
- Full DMX 512 (12 Channels)
- Large Lens for Room Filling Coverage
- Package Spec: L35 W35 H35
- Package Weight: 4.9kg Approx
Contents:
- Light Unit Lexlense 469
- IEC Power Cable with UK Plug
- Hanging Bracket and Nuts/Washers
- User Manual
Sound to Light Mode (Music Trigger)
To operate your xture so it responds to the music, please select:
Dip Switches 7 & 10 to the ON Position (as shown below)
The xture will now go through all its built in patterns one by one by
picking up sound via its built in microphone. Use the sensitivity dial
on the rear to adjust the units sensitivity to sound.
1 2 3 4 5678 9 10
on
o
Auto Play Mode
Auto Play mode is where the light will go through its inbuilt programs
one by one, regardless of any sound input. There are various pat-
terns and speeds you can choose. Please Observe below.
To put your xture into Auto-Play Mode, please select:
Dip Switches 10 to the ON Position
1 2 3 4 5 678 9 10
on
o
With number 10 dip switch set to ON, dipping other switches will
create a combination of various efffects. Please observe:
Dip 1: Will make the pattern cycle quicker.
Dip 2: Will make the pattern cycle slower.
Dip 3: Will set Auto Play Chase Mode 1 (Various Patterns)
Dip 4: Will set Auto Play Chase Mode 2 (Various Patterns)
Dip 5: Will set Auto Play Chase Mode 3 (Various Patterns)
Dip 6: Will set Auto Play Chase Mode 4 (Various Patterns)
Strobe Mode
Your Lexlense 469 has a built in strobe function.
To put your xture into Strobe Mode, please select:
Dip Switches 10 & 9 to the ON Position
1234 5 678 9 10
on
o
With number 10 & 9 dip switches set to ON, dipping other switches
will create a combination of various effects. Please Observe:
Dip 1: Will make the Strobe effect quicker
Dip 2: Will Make the Strobe effect slower
Dip 3: Will turn on all RED LED’s for Strobing
Dip 4: Will turn on all GREEN LED’s for strobing
Dip 5: Will turn on all BLUE LED’s for strobing
Dip 6: Will turn on all LED’s for strobing

To Other Slaves
(if applicable)
Master/Slave Modes
The LexLense 469 can be linked together with other LexLense 469
units to create a stunning, in-sync lightshow. This is acheived by
linking the units together via the 3 pin DMX connections at the rear.
Please see diagram below:
Lexlense 469
Master
Lexlense 469
Slave 1
Lexlense 469
Slave 2
DMX
IN OUT
DMX
IN OUT
DMX
IN OUT
Static Mode
Your Lexlense 469 allows you to switch on all LED’s for a oodlight
type effect.
To put your xture into Static Mode, please select:
Dip Switches 10 & 8 to the ON Position
1 2 3 4 5 6789 10
on
o
Master Dip Switch Setting:
1 2 3 4 5 678 9 10
on
o
Slave(s) Dip Switch Setting:
1 2 3 4 5 678 9 10
on
o
By choosing the Master program mode and connecting the DMX OUT
to another xture will allow the Slaves to copy the Master. The above
example shows the Master set to Sound-To_Light Mode. All dip switch
settings on the Slaves MUST be set to OFF.
DMX Mode
DMX (Digital Multiplex) is a universal protocol used as a form
of communication between intelligent xtures and controllers. A
DMX controller sends DMX data instructions from the controller
to the xture. DMX data is sent as serial data that travels from
xture to xture via the DATA “IN” and DATA “OUT” XLR termi-
nals located on all DMX xtures.
The LexLense 469 is a DMX enabled xture and the DMX mode
and DMX address settings are controlled via the Dip Switches.
It also carries the standard 3-pin XLR connections for DMX use.
To set your xture for use with a universal DMX controller:
Dip Switches ALL to the OFF position
12345678 9 10
o
on
With all Dip switches set to OFF position now means your
xture is now in DMX mode and is awaiting for you to assign a
DMX Fixture address. Address settings are obtained by using
dip switches 1 - 9. See example below:
Light 1 in the (01)DMX Universe - Dip 1 to ON
Light 2 in the (17)DMX Universe - Dip 1 & 5 to ON
Light 3 in the (34)DMX Universe - Dip 2 & 6 to ON
This based on the controller having 16 channels per xture.
Please see the instructions of your controller for more details on
xture addressing.
DIP #1 #2 #3 #4 #5 #6 #7 #8 #9 #10
Value 1 2 4 8 16 32 64 128 256 No
Function