LEXIBOOK MeteoClock SM1120 User manual

Copyright © Lexibook 2004 1
Congratulations on your purchase of this weather station, MeteoClock SM1120. Please take the time
to read and understand this manual so you can begin to enjoy the convenience and features this
product has to offer.
What exactly is a Weather Station?
Lexibook digital stations measure not only the time in progress - thanks to their built-in clock - but
also the actual weather!
The MeteoClock SM1120 incorporates different functions:
- Thermometer:
Temperature is displayed in real time to the nearest tenth of a degree Celsius. Thanks to its
wireless sensor, the station can sense from a distance the outside temperature or that of another
room!
- Hygrometer:
Outdoor hygrometry is expressed in percentage of humidity in the ambient air. The ideal “Comfort”
Zone for the human body ranges from 35 to 65% hygrometry for a given temperature in between
18 and 24ºC.
INTRODUCTION
Wireless Weather Station
SM1120 + ASM20 - Owners manual

Copyright © Lexibook 2004
2
FEATURES
Main Display Unit SM1120:
■12/ 24 hour clock and alarm
■Auto synchronising radio controlled clock
(DCF-77)
■local temperature display
■receives and displays temperature and
humidity readings from up to 4 remote
transmitter via RF technology of 433MHz
■minimum and maximum temperature record
■high/ low temperature alarm function
■temperature and humidity trend indicator
■weather report symbols
■LED Backlight
■user-selectable °C or °F
■battery type: 2 x AA
Remote Sensor ASM20:
■drip-proof design with LCD
■temperature display in user-selectable
°C or °F
■humidity display
■transmission range: up to 40 meters in
open area
■battery type: 2 x AA

Copyright © Lexibook 2004 3
Button placement
CHANNEL: scrolls through remote channels 1-4
ALARM/AM/PM/°C/°F: toggles between °C and °F, 12 and 24 hour
format, turns alarm on/off; clears temperature alarm
presets
MODE/SNOOZE: scrolls through time, alarm and temperature
alarm set points (high/low); activates alarm snooze
UP/HOUR/MAX: scrolls through hours; shows maximum
temperature; enables and disables backlight
DOWN/MINUTE/MIN: scrolls through minutes; show minimum
temperature
Table Stand
SET: enter to House code and Channel setting modex
°C/°F: change between °C or °F, change channel and
house code
Battery compartment
LCD display
Wall Mount Holder & Table Stand
GETTING STARTED

Copyright © Lexibook 2004
4
Battery installation
remove battery cover
2 AA size batteries (SM1120)
2 AA size batteries (ASM20)
Insert between terminals observing proper polarity then replace cover
LOW BATTERY INDICATION: Low battery indication will be flashing low battery indicator (for both
indoor & outdoor). On transmitter, will be displayed.
Setting remote transmitters
Insert batteries to start setup
HOUSE CODE will flash for 8 seconds
Select HOUSE CODE (1-15) by pressing °C/°F and then press SET
Transmitters for each receiver must be set to the same HOUSE CODE and pressing SET
CHANNEL will flash for 8 seconds
Select CHANNEL(1-4) by pressing °C/°F and then press SET
Humidity & Temperature will display
Select °C or °F of Temperature by pressing °C/°F key
* Use a different house code if your weather station detecTs other signals from
neighboring sources
* Factory default: house code = 01 and channel = 01
GETTING STARTED

Copyright © Lexibook 2004 5
SYNCHRONIZATION
Automatic Learn Function
Learn function executes automatically and runs for
approximately 3 minutes when batteries are first
installed in the receiver.
Within these 3 minutes, receiver picks up the temperature & humidity signals from remote
transmitter and displays the readings.
Manual-Learn (Searching for Remote Signals)
If a new remote transmitter is added or if signal is lost (outdoor display blinking), learn function must
be executed again.
Press & hold ALARM/AM/PM/°C/°F for 3 seconds to start.
Beep sound indicates that learn function has started.
CHANNEL symbol will flash and unit will beep as each transmitter is
detected.
Temperature & humidity readings of remote transmitter displays on the
receiver.
Press & hold Channel for 3 seconds to start auto channel scroll function. In this mode, the
display will scroll through the data from all the valid channels, each of which will be shown for
8 seconds. Press & hold Channel for 3 seconds again to disable this function.
SETUP

Copyright © Lexibook 2004
6
Clock setting;
Modes are arranged in a circular pattern starting with clock:
Press and hold MODE/SNOOZE until time flashes.
Select hour using UP/HOUR/MAX.
Select minute using DOWN/MINUTE/MIN.
Press ALARM/PM/AM/°C/°F to toggle between 12 or 24 hour format.
Alarm setting:
Select alarm mode using MODE/SNOOZE.
Select hour using UP/HOUR/MAX.
Select minute using DOWN/MINUTE/MIN.
In alarm mode, press ALARM to toggle alarm On and Off.
When alarm sounds, will flash .
Press MODE/SNOOZE to snooze the alarm for 5 minutes. After
that the alarm will sound again.
Press ANY other key will shut off the alarm.
Without interruption, alarm will shut off automatically after one minute.
CLOCK & ALARM SETTING

Copyright © Lexibook 2004 7
Check Local Temperature
Local temperature displays instantly after batteries are inserted.
Check Remote Temperature & Humidity
Press CHANNEL to toggle between Channel 1, 2, 3 and 4. Temperature and humidity readings will
alternately display on the receiver.
°C or °F Temperature Display
Toggle between °C and °F by pressing ALARM/PM/AM/°C/°F in clock mode.
Min and Max Temperature
Press DOWN/MINUTE/MIN in Clock mode to display
minimum temperature record.
Press UP/HOUR/MAX in Clock mode to display
maximum temperature record.
Note:
Min/Max temperature records are automatically cleared daily at 00:00.
WEATHER DISPLAY

Copyright © Lexibook 2004
8
Temperature & humidity trend
The trend indicator shows the trend of temperature and humidity determined by the particular
transmitter in the past half-hour interval.
Weather report symbols
The receiver is able to monitor and display the weather status based on collected data from Channel 1.
About Freeze Warning
* Snow symbol will flash to warn of 'snowing'.
* Activated when Channel 1's temperature is between -1.9 °C and +2.9 °C.
* Snow will appear solid if and when Channel 1's temperature falls below -1.9 °C: it is freezing.
Note:
* Initially, the weather will be cloudy
* Remote transmitter Channel 1 will be used for weather indication.
* If Channel 1 is empty, then weather will always be cloudy.
* If Channel 1 has no humidity data, weather indication will always be cloudy, but freeze warning
and snow indication will be available.
WEATHER DISPLAY

Copyright © Lexibook 2004 9
The temperature alarm function allows you to have an alarm sound if the temperature rises above
or drops below a particular set point.
High temperature alarm
Scroll to high temperature alarm mode using MODE/SNOOZE..
and or existing preset will flash.
Select channel (1, 2, 3, 4 or local) using CHANNEL.
Press +or -key to set the high temperature limit value.
To disable particular alarm, press ALARM/PM/AM/°C/°F
; dashes = alarm disabled.
Press MODE/SNOOZE to finish.
Repeat steps to for all other channels if desired.
Low temperature alarm
Scroll to high temperature alarm mode using MODE/SNOOZE..
and or existing preset will flash.
Select channel (1, 2, 3, 4 or local) using CHANNEL.
Press +or -key to set the low temperature limit value.
To disable particular alarm, press ALARM/PM/AM/°C/°F
; dashes = alarm disabled.
Press MODE/SNOOZE to finish.
Repeat steps to for all other channels if desired.
TEMPERATURE ALARM

Copyright © Lexibook 2004
10
Once the high/low temperature alarm is set for a particular channel, and/or will appear
on display for that channel
When alarm sounds, the sounding channel is displayed, and or flashes to indicate
whether it is the high or low temperature alarm. Press any button to shut off alarm.
To clear high/low temperature alarm
Select high/low temperature alarm set point using MODE/SNOOZE..
Press ALARM/PM/AM/°C/°F to clear value.
Press MODE/SNOOZE to finish setting.
To view maximum temperature
Toggle between current and maximum temperature using UP/HOUR/MAX.
Press CHANNEL to view the maximum temperature for other channels.
Pour voir la température minimum
Toggle between current and maximum temperature using
DOWN/MINUTE/MIN.
Press CHANNEL to view the maximum temperature for other channels.
OTHER FEATURES
MODE/SNOOZE

Copyright © Lexibook 2004 11
TROUBLESHOOTING
Solution:
Re-synchronize receiver by holding
ALARM/PM/AM/°C/°F for 3 seconds until a
beep is heard.
Ensure the remote transmitter is out of direct
sunlight, and away from sources of heat.
Repeat the learning procedures.
- Temperature may be below -30°C.
- Batteries in remote transmitter may need
changing.
- Move remote transmitter closer to the receiver.
- Make sure remote transmitter is away from
sources of electrical disturbance.
Problem:
The temperature measurement of
remote transmitter and receiver does
not match.
Temperature reading of the outdoor
remote transmitter seems too high.
Receiver is no longer receiving
remote transmitter signals or tempe-
rature display reads Lo.

Copyright © Lexibook 2004
12
Additional sensor :
Mesure temperature and hygrometry in other places!
- upstairs
- in the baby's bedroom
- in the basement
- in the garden
- in another room
To order: 0808 100 3015
or www.lexibook.com
This product is covered by our two-year warranty.
To make use of the warranty or the after-sales service, please contact your retailer and supply proof
of purchase. Our warranty covers material or installation-related defects attributable to the
manufacturer, with the exception of wear caused by failure to respect the instructions for use or any
unauthorised work on the equipment (such as dismantling, exposure to heat or damp, etc.).
For technical assistance call 0808 100 3015
Web: http://www.lexibook.co.uk
Email: [email protected]
WARRANTY
ACCESSORIES