LF allen + roth DUALHEAT GAD19104L User manual

Table of Contents
Important Safeguards ...........................................................Page 2
Expanded View and Hardware......................................................... 5
Assembly Instructions............................................................... 6
Installing LP Gas Tank............................................................... 9
Operating Instructions.............................................................. 10
Cleaning and Care ................................................................ 10
Product Registration ............................................................... 12
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Limited Warranty ................................................................. 12
Specifications.................................................................... 12
Troubleshooting .................................................................. 13
The use and installation of this product must conform to local codes. In absence of local codes, use the
latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or International Fuel Gas Code. This
appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence
of local codes with the National Electrical Code, ANSI/NFPA 70, if applicable.
For installation in Canada - these instructions, while generally acceptable, do not necessarily comply with
the Canadian installation codes, particularly with piping above and below ground. In Canada the installation
of this appliance must comply with local codes and/or standard CAN/CGA B149.1 (installation code for
propane burning appliances and equipment).
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
If you are assembling this unit for someone else, give this manual to them to read and save for future reference.
WARNING: This product can expose you to chemicals, including carbon monoxide, soot, Diisononyl
Phthalate (DINP), lead and lead components which are known to the State of California to cause cancer,
birth defects, and other reproductive harm. Wash your hands after handling this product. For more
information go to www.P65Warnings.ca.gov.
Made from 75% Bagasse
(environmentally friendly sugar
cane pulp by-product)
CARBON MONOXIDE HAZARD
• This appliance can produce carbon monoxide which has
no odor.
• Using it in an enclosed space can kill you.
• Never use this appliance in an enclosed space such as a
camper, tent, car or home.
·DANGER
PATENT NO. 10,684,020
Manufactured in China for: Mr. Bar-B-Q Products LLC
10 Hub Dr., Ste 101, Melville, NY 11747 • MrBarBQProducts.com
© Mr. Bar-B-Q Products LLC
allen + roth®is a registered trademark of LF, LLC. All Rights Reserved. GAD19104L-ES-OM-F100
WARNING
FOR OUTDOOR USE ONLY.
WInstallation and service must be performed
by a qualified installer, service agency or
gas supplier.
WARNING
FOR YOUR SAFETY:
WIf the information in this manual is not
followed exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
WWHAT TO DO IF YOU SMELL GAS:
• Do NOT try lighting any appliance.
• Do NOT touch any electrical switch; do
NOT use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone.
• Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
WDo Not Use For Cooking.
WARNING
FOR YOUR SAFETY:
WINSTALLER: Leave this manual with the
appliance.
WCONSUMER: Retain this manual for future
reference.
WARNING
FOR YOUR SAFETY:
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage.
Read the installation, operation and
maintenance instructions thoroughly before
installing or servicing this equipment.
DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:
• Shut off gas to appliance.
• Extinguish any open flame.
• If odor continues, leave the area
immediately.
• After leaving the area, call your gas
supplier or fire department.
Failure to follow these instructions could
result in fire or explosion, which could cause
property damage, personal injury, or death.
WARNING
FOR YOUR SAFETY:
1. Do not store or use gasoline, or other
flammable vapors and liquids, in the vicinity
of this or any other appliance.
2. An LP-cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
DANGER
Do NOT leave this appliance unattended while
it is in operation.
@GAS FIRE PIT
#2592447
Model No. GAD19104L
OWNER’S MANUAL
®
TM

Important Safeguards Important Safeguards
DANGER • FLAMMABLE GAS UNDER PRESSURE.
LEAKING LP-GAS MAY CAUSE A FIRE OR EXPLOSION IF IGNITED CAUSING
SERIOUS BODILY INJURY OR DEATH.
CONTACT LP GAS SUPPLIER FOR REPAIRS, OR DISPOSAL OF THIS
CYLINDER OR UNUSED LP-GAS.
WARNING • FOR OUTDOOR USE ONLY.*
DO NOT USE OR STORE CYLINDER IN A BUILDING,
GARAGE OR ENCLOSED AREA.
• Know the odor of LP-gas. If you hear, see or smell
leaking LP-gas, immediately get everyone away from
the cylinder and call the Fire Department. Do not attempt
repairs.
• Caution your LP-gas supplier to:
Be certain cylinder is purged of trapped air prior to
first filling.
Be certain not to over fill the cylinder.
Be certain cylinder requalification date is checked.
• LP-gas is heavier than air and may settle in low places
while dissipating.
• Contact with the liquid contents of cylinder will cause
freeze burns to the skin.
• Do not allow children to tamper or play with cylinder.
• When not connected for use, keep cylinder valve turned
off. Self contained appliances shall be limited to a
cylinder of 30 lb capacity or less.
• Do not use, store or transport cylinder where it would
be exposed to high temperatures. Relief valve may open
allowing a large amount of flammable gas to escape.
• When transporting, keep cylinder secured in
an upright position with cylinder valve turned off.
WHEN CONNECTING FOR USE:
• Use only in compliance with applicable codes.
• Read and follow manufacturer’s instructions.
• Consult manufacturer’s instructions concerning the
cylinder connection provided with your appliance.
• Be sure regulator vent is not pointing up.
• Turn off all valves on the appliance.
• Do not check for gas leaks with a match or open flame.
Apply soapy water at areas marked “X”. Open cylinder
valve. If bubble appears, close valve and have LP-gas
service person make needed repairs. Also, check
appliance valves and connections to make sure they do
not leak before lighting appliance.
• Light appliance(s) following manufacturer’s instructions.
• When appliance is not in use, keep the cylinder valve
closed.
WARNING:
DO NOT REMOVE, DEFACE, OR OBLITERATE THIS LABEL
*EXCEPT AS AUTHORIZED BY ANSI/NFPA 58.
DANGER. Do not store a spare LP cylinder under or near a barbecue grill, or other heat sources.
NEVER fill an LP cylinder beyond 80% full: a fire causing death or serious injury may occur.
2 Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase

WDo NOT use this outdoor fire pit without reading the entire owner’s
manual.
WThis appliance is for outdoor use only, and should NOT be used in a
building, garage or any other enclosed area.
WDo NOT operate, light or use this appliance within ten feet (3.05 m) of
walls, structures or buildings.
WFor residential use only. This outdoor fire pit is NOT for commercial use.
WDo NOT use this outdoor fire pit for indoor heating. TOXIC carbon
monoxide fumes can accumulate and cause asphyxiation.
WThis outdoor fire pit is safety certified for use in the United States
and/or Canada only. Do NOT modify for use in any other location.
Modification will result in a safety hazard and will void your warranty.
WApartment dwellers: Check with management to learn the requirements
and fire codes for using a liquid propane (LP) gas outdoor fire pit in your
apartment complex. If allowed, use outside on the ground floor with a
ten foot (3.05 m) clearance from any structure. Do NOT use on or under
balconies.
WThis outdoor fire pit, from the factory, is for use with LP gas only. The
conversion to or attempted use of natural gas in this outdoor fire pit is
dangerous, may cause bodily harm and will void your warranty.
WLP gas characteristics:
a. LP gas is flammable and hazardous if handled improperly. Become
aware of the characteristics before using any LP gas product.
b. LP gas is explosive under pressure, heavier than air, and settles/
pools in low areas.
c. LP gas in its natural state has no odor. For your safety, an odorant is
added that smells like rotten cabbage.
d. Contact with LP gas can cause freeze burns to skin.
WLP gas tank needed to operate. Only tanks marked “propane” may be
used.
a. The LP gas cylinder must be constructed and marked in accordance
with the U.S. Department of Transportation (D.O.T.) Specifications for
LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes
for the Transportation of Dangerous Goods and Commission, CAN/
CSA-B339 as applicable.
b. LP gas tank must be arranged for vapor withdrawal.
c. The LP gas tank must have a listed overfilling prevention device
(OPD) and a QCCI or Type I (CGA810) LP gas tank connection.
d. The LP gas tank must have a tank collar to protect the tank valve.
e. Never use an LP gas tank with a damaged body, valve, collar or
footing.
f. Dented or rusted LP gas tanks may be hazardous and should be
checked by your LP gas supplier prior to use.
g. The LP gas tank should not be dropped or handled roughly.
h. Tanks must be stored outdoors, out of the reach of children and
must not be stored in a building, garage or any other enclosed area.
Your LP gas tank must never be stored where temperatures can
reach over 125°F.
i. Do NOT insert any tool or foreign object into the valve outlet or
safety relief valve. You may damage the valve and cause a leak.
Leaking propane may result in explosion, fire, severe personal injury
or death.
j. Never keep an LP gas tank in a hot car or trunk. Heat will cause the
gas pressure to increase, which may open the relief valve and allow
gas to escape.
k. Place dust cap on cylinder valve outlet whenever the cylinder is not
in use. Only install the type of dust cap on the cylinder valve outlet
that is provided with the cylinder valve. Other types of caps or plugs
may result in leakage of propane.
l. Do NOT store a spare LP gas tank under or near this appliance.
m. Never fill the cylinder beyond 80 percent full.
n. A fire causing serious injury or damage to property may occur if the
above is not followed exactly.
WYour outdoor fire pit has been checked at all factory connections
for leaks. Recheck all connections as described in the “Operating
Instructions” section, as shipping can loosen connections.
WCheck for leaks even if your unit was assembled for you by someone
else.
WDo NOT operate if a gas leak is present. Gas leaks may cause a fire or
explosion.
WYou must follow all instructions in the “Checking for Leaks” section
before operating. To prevent a fire or explosion when testing for a leak:
a. Always perform a leak test before lighting this outdoor fire pit and
each time the tank is connected for use.
b. No smoking. Do NOT use or permit sources of ignition in the area
while conducting a leak test.
c. Conduct the leak test outdoors in a well-ventilated area.
d. Do NOT use matches, lighters or a flame to check for leaks.
e. The use of alcohol, prescription or non-prescription drugs may
impair the consumer’s ability to properly assemble or safely operate
the appliance.
f. Strong odors, colds, sinus congestion, etc. may prevent the
detection of propane. Use caution and common sense when testing
for leaks.
g. Do NOT use this outdoor fire pit until any and all leaks are corrected.
If you are unable to stop a leak, disconnect the LP gas supply. Call a
gas appliance serviceman or your local LP gas supplier.
WDo NOT store or use gasoline or other flammable liquids or vapors
within 25 feet (7.62 m) of this appliance.
WDo NOT use in an explosive atmosphere. Keep outdoor fire pit area clear
and free from combustible materials, gasoline and other flammable
vapors and liquids.
WThis outdoor fire pit is NOT to be operated by children.
WThis outdoor fire pit is NOT to be used in or on boats or recreational
vehicles.
WDo NOT connect to a remote gas supply.
WNever attempt to attach this outdoor fire pit to the self-contained LP gas
system of a camper trailer, motor home or house.
WAlways use in accordance with all applicable local, state and national
codes. Contact your local fire department for details on outdoor burning.
WWhen using this outdoor fire pit, exercise the same precautions you
would with any open fire.
WDo NOT burn solid fuels such as: wood, charcoal briquettes, lump
charcoal, manufactured logs, driftwood, trash, leaves, paper, cardboard,
plywood, painted/stained/pressure treated wood in this outdoor fire pit.
WIt is essential to keep the outdoor fire pit’s valve compartment, burners,
and circulating air passages clean. Inspect outdoor fire pit before each
use.
WDo NOT use this outdoor fire pit until it is COMPLETELY assembled and
all parts are securely fastened and tightened.
WDo NOT use this outdoor fire pit near automobiles, trucks, vans or
recreational vehicles.
WDo NOT use this outdoor fire pit under any overhang or near any
unprotected combustible constructions. Avoid using near or under
overhanging trees and shrubs.
WAlways use this outdoor fire pit on a hard, level, non-combustible
surface such as concrete, rock or stone. An asphalt or blacktop surface
may not be acceptable for this purpose.
WDo NOT use this outdoor fire pit for cooking.
WDANGER: Failure to follow the dangers, warnings and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion
causing damage to property.
WWARNINGS:
Important Safeguards Important Safeguards
Gas Fire Pit
Model No. GAD19104L
®
3
@
TM

4
WDo NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance
and to replace any part or control system and any gas control which
has been under water.
WDo NOT wear flammable or loose clothing when operating this outdoor
fire pit.
WDo NOT use in windy conditions.
WNever lean over this outdoor fire pit when lighting or when in use.
WDo NOT use this outdoor fire pit unless burner is securely in place.
WKeep all electrical cords away from this outdoor fire pit during use.
WCertain areas of this outdoor fire pit when in use will become too
hot to touch. To avoid burns, do NOT touch hot surfaces until the unit
has completely cooled (about 45 minutes), unless you are wearing
protective gear (such as insulated pot holders or heat-resistant gloves/
mittens).
WDo NOT leave a lit outdoor fire pit unattended, especially around children
and pets.
WChildren and adults should be alerted to the hazards of high surface
temperatures and should stay away to avoid burns or clothing ignition.
WYoung children should be carefully supervised when they are in the area
of the appliance.
WDo NOT hang or place clothing or other flammable material on or near
this appliance.
WAny guard or other protective device removed for servicing the
appliance must be replaced prior to operating the appliance.
WIf applicable, protective cover must be removed when burner is in
operation.
WDo NOT attempt to move outdoor fire pit when in use. Allow the outdoor
fire pit to cool before moving or storing.
WThis outdoor fire pit should be thoroughly cleaned and inspected on
a regular basis. Clean and inspect the hose before each use of the
appliance. If there is evidence of abrasion, wear, cuts, or leaks, the hose
must be replaced prior to the appliance being operated.
WThis outdoor fire pit should be inspected at least annually by a qualified
service person. Depending on amount of use, more frequent cleaning
may be required. Do NOT operate until all parts have been repaired or
replaced.
WUse only the regulator and hose assembly provided. Use only the
replacement regulator and hose assembly specified by Mr. Bar-B-Q
Products LLC.
WUse only Mr. Bar-B-Q Products LLC factory-authorized parts. The use of
any part that is not factory-authorized can be dangerous and will void
your warranty.
WUse only Mr. Bar-B-Q Products LLC factory-authorized fire glass /lava
rock. The use of any fire glass/lava rock that is not factory-authorized
can be dangerous and will void your warranty.
WDo NOT operate this appliance without reading “Operating Instructions”
in this manual.
WStorage of this outdoor fire pit indoors is permissible only if the tank
is disconnected, removed from the outdoor fire pit and properly stored
outdoors.
WDo NOT attempt to disconnect the gas regulator from the tank or any
gas fitting while the outdoor fire pit is in use.
WIf the outdoor fire pit is not in use, the gas must be turned off at the
supply tank.
WCAUTION: The gas pressure regulator provided with this appliance must
be used. This regulator is set for an outlet pressure of 11 inches water
column.
WThe minimum inlet gas pressure for this outdoor fire pit is 11 inches of
water column, for the purpose of input adjustment.
WThe maximum inlet gas pressure for this outdoor fire pit is 11 inches of
water column.
WBefore pressure testing, close LP gas tank valve and disconnect gas
regulator. The gas supply piping system must test at pressures equal to
or less than ½ psi (3.5 kPa).
WDo NOT sit or stand on the mantle or any part of this appliance.
WDo NOT throw anything onto the fire when the unit is in operation.
WFire glass/lava rock are very hot. Keep children or pets at a safe
distance from this appliance.
WWhen heated, lava rock/fire glass may pop.
WThe opening of the tank collar should face toward the door side for easy
access.
WDo NOT store any combustible materials in the base enclosure.
WUse protective gloves when assembling this product.
WDo NOT force parts together as this can result in personal injury or
damage to the product.
WDeath, serious injury or damage to property may occur if the above is
not followed exactly.
Important Safeguards
Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase

Tools Required for Assembly (Not Included)
#2 Phillips Head Screwdriver 1 pc
Hardware Pack 58-24-397
AScrew M5x12 Black Nickel Plated Truss Head 22 pcs
BScrew M6X12 Black Nickel Plated Step Head 1 pc
CScrew M5x25 Black Nickel Plated Truss Head 4 pcs
DScrew M4x8 Black Nickel Plated Truss Head 1 pc
EAA Battery 1 pc
Parts List
1Black Fire Glass GLS-BLK
2Table Insert 58-24-521
3Fire Pit/Heater Unit* 58-24-522
Battery Cap* 58-23-897
Control Knob(2)* 58-23-139
Regulator/Hose
Assembly* 58-24-181
Lighting Hook 58-24-387
Lower Panel (3) 58-24-523
6Door 58-24-524
7Door Knob* 58-24-391
8Base* 58-24-389
LP Gas Tank Retainer
Bolt* 58-23-149
LP Gas Tank Prevent Bar 58-24-388
Leg A (2) 58-24-392
Leg B 58-24-393
Leg C 58-24-394
Magnet* 58-23-804
15 Foot (4)* 58-23-147
16 Cover 58-24-525
17 Lava Rock (not required
and sold separately)** 55-05-833
* Pre-assembled
W**CAUTION: Use only Mr. Bar-B-Q
Products LLC factory-authorized
fire glass/lava rock. The use of
any fire glass/lava rock that is
not factory-authorized can be
dangerous and will void your
warranty.
Expanded View
Sold Separately
17
9
13
10
11
12
1
7
2
8
5
6
13
3
9
5
5
10
16
11
11
12
14
15
15 15
3
4
4
14
3.2
3.3
5
3.1
3.1
3.2
3.3
WARNING
When heated, lava rocks may react
by breaking and throwing fragments
of rock. Be sure to season the lava
rocks at a high temperature before
use in order to avoid potential
personal injury or damage.
IMPORTANT BEFORE USE
HOW TO SEASON LAVA ROCK ON
PAGE 11.
®Gas Fire Pit
Model No. GAD19104L
@
TM
5
Non-rechargeablebatteriesarenottoberecharged.
Batteriesaretobeinsertedwiththecorrectpolarity.
Exhaustedbatteriesaretoberemovedfromtheproduct.
DONOTDISPOSEOFBATTERIESIN FIRE.BATTERIESMAYEXPLODEORLEAK.

1
DO NOT RETURN TO PLACE OF PURCHASE.
For assistance, call 1-866-439-9800 toll-free. Please have your
owner’s manual and model number available for reference.
Note: The model number is printed on a label which can be found on the inside door,
back or side of the base assembly.
Assembly Tips:
1. Select an area where you will assemble this product. To protect components,
choose a smooth surface that’s free of cracks or openings.
2. Spread out all parts.
3. Tighten all hardware connections by hand first. Then, before completing each
step, go back and fully tighten all hardware. Be careful not to over-tighten.
That could damage surfaces or strip threads.
4. For best results, complete each step in the order presented.
To complete assembly you will need:
• (1) Leak detection solution (instructions on how to make the solution are
included in the “Operating Instructions” section of this manual).
• (1) Precision-filled LP gas grill tank with Acme Type 1 external threaded valve
connection (standard grill size) (not included).
Typical assembly is approximately one hour.
WCAUTION: Two (2) people will be required for assembly.
WWARNING: Failure to position the parts in accordance with
these diagrams or failure to use only parts specifically
approved with this appliance may result in property damage
or personal injury.
Assembly Instructions
4
Attach Side and Rear Panels
Note: Attach bottom screws before attaching top screws. Do not fully tighten screws
until step 5.
Ax 12
3
Attach Legs
WCAUTION: TWO (2) PEOPLE WILL BE REQUIRED TO TURN THE
OUTDOOR FIRE PIT OVER.
WCAUTION: TO AVOID SCRATCHES CHOOSE A SMOOTH SURFACE
THAT’S FREE OF CRACKS OR OPENINGS.
Note: Do not fully tighten screws until step 5.
Ax 8
2
Turn Outdoor Fire Pit Over
WCAUTION: Two (2) people will be required to turn the outdoor
fire pit over.
WCAUTION: To avoid scratches choose a smooth surface that’s
free of cracks or openings.
11 11
13
12
A
6
A
Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase

Assembly Instructions (continued)
6
Attach Door Knob and Door and Turn Outdoor Fire Pit
Over
WCAUTION: Two (2) people will be required to turn the outdoor
fire pit upright on feet.
Bx 1 Dx 1
7
Place Fire Glass
WCAUTION: Do NOT dump fire glass out of package. Carefully
place fire glass by hand so dust does not clog burner.
WCAUTION: Use only Mr. Bar-B-Q Products LLC factory-
authorized fire glass. The use of any fire glass that is not
factory-authorized can be dangerous and will void your
warranty.
WCAUTION: Do NOT cover igniter cover.
Note: Fire glass should be 0.8-1.6 in (2-4 cm) diameter. Approx. 11 lbs (5 kg) of fire
glass is needed.
8
Place Table Insert
WWARNING: NEVER place table insert on outdoor fire pit while
in use.
WWARNING: NEVER place table insert on outdoor fire pit while
the outdoor fire pit is still hot.
5
Attach LP Gas Tank Prevent Bar to Base, then Attach
Base
Note: Tighten all screws from steps 2-5.
Ax 2 Cx 4
A
CD
B
®Gas Fire Pit
Model No. GAD19104L
@
TM
7

11
Store Table Insert
Hang the table insert on the inner side of door.
WWARNING: NEVER place table insert onto outdoor fire pit while
in use.
WWARNING: NEVER take out and place table insert onto outdoor
fire pit while the outdoor fire pit is still hot.
9
Insert Battery
Note: Remove plastic wrapper before installing battery.
Ex 1
OPTIONAL ITEM SOLD SEPARATELY
10
Place Lighting Hook
E
+-
12
Place Lava Rocks
WCAUTION: When switching from fire glass, remove all fire
glass before placing lava rock.
WCAUTION: Do NOT dump lava rocks out of package. Carefully
place lava rocks by hand so dust does not clog burner.
WCAUTION: Use only Mr. Bar-B-Q Products LLC factory-
authorized lava rock. The use of any lava rock that is not
factory-authorized can be dangerous and will void your
warranty.
WCAUTION: Do NOT cover igniter cover.
Note: Lava rocks should be 0.8-2.0 in. (2-5 cm) diameter. Approx. 5.07 lbs. (2.3 kg)
of lava rocks are needed.
Assembly Instructions (continued)
8 Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase

Checking for Leaks
WWARNING: Before using this outdoor
fire pit, make sure you have read,
understand and are following
all information provided in the
“Important Safeguards” section
on page 2. Failure to follow those
instructions can cause death, serious
injury or property damage.
WWARNING: The burner must be
replaced prior to the appliance being
put into operation if it is evident
that the burner is damaged. The
replacement burner shall be that
specified by the manufacturer.
Burner Connections
1. Make sure the regulator hose and valve
connections are securely fastened to the burner
and the tank.
2. Visually check the connection between the
burner/venturi tube and orifice.
3. Make sure the burner/venturi tube fits over the
orifice.
WWARNING: Failure to inspect
this connection or follow these
instructions could cause a fire or an
explosion which can cause death,
serious bodily injury or damage to
property.
4. Please refer to diagram for proper installation
(Figures 1 and 2).
5. If the burner/venturi tube does not rest flush
to the orifice, as shown, please contact
1-866-439-9800 for assistance.
Tank/Gas Line Connection
1. Make 2-3 oz. of leak detection solution by
mixing one part liquid dishwashing soap with
three parts water.
2. Make sure control knobs are in the “ OFF”
position (Figure 3).
3. Connect LP gas tank per “Installing LP Gas
Tank” section.
4. Turn LP gas tank valve to “OPEN.”
5. Spoon several drops of solution, or use a squirt
bottle, at all “X” locations (Figures 1 and 2).
a. If any bubbles appear, turn LP gas tank valve
to “CLOSED,” reconnect and re-test.
b. If you continue to see bubbles after
several attempts, turn LP gas tank valve to
“CLOSED” and disconnect LP gas tank, per
“Disconnecting LP Gas Tank” section. Contact
1-866-439-9800 for assistance.
c. If no bubbles appear after one minute, turn
LP gas tank valve to “CLOSED,” wipe away
solution and proceed.
Upper Burner Lighting
WDANGER: Failure to follow these
lighting instructions may result in
serious bodily injury or death, or in a
fire or an explosion causing damage
to property.
WWARNING: NEVER light the burner
with the cover on the outdoor fire pit.
WCAUTION: Keep outdoor gas appliance area clear and free from
combustible materials, gasoline and other flammable vapors and
liquids.
WCAUTION: Do NOT obstruct the flow of combustion and ventilation air.
WCAUTION: Check and clean burner/venturi tubes for insects and insect
nests. A clogged tube can lead to a fire.
Note: The upper and lower burners are independent.
Note: This outdoor fire pit is equipped with a pilot light that allows for safer startups and
shutdowns. Pilot must be lit before main burner can be started.
Lighting
1. Make sure all labels, packaging and protective films have been removed from the outdoor
fire pit.
2. Check for obstructions of airflow to the burner. Spiders, insects and webs can clog the
burner/venturi tube. A clogged burner tube can lead to a fire.
3. The control knobs must be in the “ OFF” position (Figure 3).
Installing LP Gas Tank
To operate, you will need one precision-filled standard grill LP gas
tank with external valve threads.
WCAUTION: LP gas tank must be properly
disconnected and removed prior to moving this
outdoor fire pit.
Inserting LP Gas Tank
WWARNING: Make sure LP gas tank valve is closed.
1. Open door.
2. Make sure the control knobs is in the “ OFF” position (Figure 3).
3. Loosen LP gas tank retainer bolt by turning counter-clockwise.
4. Place precision-filled LP gas tank upright into hole in outdoor fire pit base so the tank valve
is facing the gas line connection.
5. Secure tank by turning LP gas tank retainer bolt clockwise until tight.
6. Close door.
Connecting LP Gas Tank
1. Make sure the control knob is in the “ OFF” position
(Figure 3).
2. Before connecting, be sure there is no debris caught in the
head of the LP gas tank, head of the regulator valve or in the
head of the burner or burner ports.
3. Connect regulator/hose assembly to tank by turning knob
clockwise until it stops.
4. Perform leak check per “Checking for Leaks” section.
Disconnecting LP Gas Tank
1. Make sure the control knob is in the “ OFF” position
(Figure 3).
2. Before disconnecting, make sure the LP gas tank valve is
“CLOSED.”
3. Disconnect regulator/hose assembly from LP gas tank by
turning knob counterclockwise until it is loose.
WCAUTION: LP gas tank must be properly
disconnected and removed prior to moving this outdoor fire pit.
4. Place the protective cap cover on the LP tank and store the tank outdoors in a well
ventilated area out of direct sunlight.
20 lb
9 Kg
17.9 in. / 45.5 cm
12.2 in. / 31 cm
Figure 1
LP Gas
Connection
LP Gas Valve
with Orifice
Figure 2
X
XX
XX
Figure 3
OFF / APAGADO
Figure 4
K
F
AA
Figure 5
11.8 in. – 19.7 in.
30 – 50 cm
®Gas Fire Pit
Model No. GAD19104L
@
TM
9

Operating Instructions
4. Clear small area of glass rocks away from the igniter cover (Figure 4).
5. Connect LP gas tank per “Installing LP Gas Tank” section.
6. Turn LP gas tank valve to “OPEN.”
7. Push and turn control knob to (HIGH). Continue to hold the control knob in to light.
8. After the fire pit lights, continue to hold the control knob in for 20 seconds, you will hear
clicking as you hold the knob in for 20 seconds. This heats the thermocouple, a safety
device that stops the gas flow when a fire pit is not lit and warms it up so the gas flow will
continue.
9. After 20 seconds, release and turn control knob counterclockwise to adjust flame to
desired height.
10. After three attempts, if ignition does not occur, turn the burner control knob to “ OFF.”
11. Wait 5 minutes, fan with a newspaper or magazine, and repeat lighting procedure.
12. If igniter does not light burner:
a. Wearing heat-resistant gloves, position a lit long match or lit long butane lighter near
the pilot housing (Figure 4).
b. Push and turn control knob to (HIGH).
c. Remove match/lighter once burner is lit.
WCAUTION: After lighting - using a fire pit tool and heat-resistant
gloves, carefully move the fire glass/lava rock back to their proper
position, being careful to avoid the flame.
13. After lighting, observe the burner flame. Make sure all burner ports are lit and flame height
matches illustration (Figure 5).
WCAUTION: If ignition does not occur in 5 seconds, turn control knob
to “ OFF,” wait 5 minutes, fan with a newspaper or magazine, and
repeat lighting procedure.
Turning Off
1. Turn LP gas tank valve to “CLOSED.”
2. Turn control knob to the “ OFF” position.
Note: A “poof” sound is normal as the last of the LP gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
Lower Burner Lighting
WDANGER: Failure to follow these lighting instructions may result in
serious bodily injury or death, or in a fire or an explosion causing
damage to property.
WWARNING: NEVER light the burner with the cover on the outdoor fire
pit.
WWARNING: Always use this outdoor fire pit on a hard, level, non-
combustible surface such as concrete, rock or stone. An asphalt or
blacktop surface may not be acceptable for this purpose.
WCAUTION: Keep outdoor gas appliance area clear and free from
combustible materials, gasoline and other flammable vapors and
liquids.
WCAUTION: Do NOT obstruct the flow of combustion and ventilation air.
WCAUTION: Check and clean burner/venturi tubes for insects and insect
nests. A clogged tube can lead to a fire.
WCAUTION: If relighting a hot heater,
always wait at least 5 minutes before
relighting.
Note: The upper and lower burners are independent.
Note: This outdoor fire pit is equipped with a pilot
light that allows for safer startups and shutdowns.
Pilot must be lit before main burner can be started.
Lighting
1. Make sure all labels, packaging and protective
films have been removed from the outdoor fire
pit.
2. Check for obstructions of airflow to the burner.
Spiders, insects and webs can clog the burner/
venturi tube. A clogged burner tube can lead to
a fire.
3. The control knobs must be in the “ OFF”
position (Figure 3).
4. Connect LP gas tank per “Installing LP Gas
Tank” section.
5. Slowly turn LP gas tank valve 1 revolution to
“OPEN.”
6. Push and turn control knob to (HIGH). Continue
to hold the control knob in to light.
7. After the fire pit lights, continue to hold the
control knob in for 20 seconds, you will hear
clicking as you hold the knob in for 20 seconds.
This heats the thermocouple, a safety device
that stops the gas flow when a fire pit is not lit
and warms it up so the gas flow will continue.
8. After 20 seconds, release and turn control knob counterclockwise to adjust heat to desired
temperature.
9. After three attempts, if ignition does not occur, turn the burner control knob to “ OFF.”
10. Wait 5 minutes, fan with a newspaper or magazine, and repeat lighting procedure.
11. If igniter does not light burner:
a. Use a lit matchbook match secured with the lighting hook (included with the outdoor
fire pit) to light the lower burner.
b. Access the burner through the side Panel (Figure 6).
c. Position lit match near side of burner (Figure 7).
Important: Always use the lighting hook (included) when lighting burners with a
match.
d. Push and turn control knob to (HIGH).
e. Remove match/lighter once burner is lit.
WCAUTION: After lighting - using a fire pit tool and heat-resistant
gloves, carefully move the fire glass/lava rock back to their proper
position, being careful to avoid the flame.
12. After lighting, observe the burner flame. Make sure all burner ports are lit and flame height
matches illustration (Figure 8).
WCAUTION: If ignition does not occur in 5 seconds, turn control knob
to “ OFF,” wait 5 minutes, fan with a newspaper or magazine, and
repeat lighting procedure.
TIP: The burner may be noisy when initially lit. To eliminate excessive noise from the burner
turn the control knob to the (pilot) position, then turn the knob to the level of heat desired.
TIP: Remove manufacturing oils on this heater for the first time by operating the heater for at
least 15 minutes on (HIGH). This will “heat clean” the internal parts and dissipate odors.
When Heater is On
WWARNING: Dome and burner are extremely hot to the touch during
operation. Never touch the dome or burner while the heater is
operating. The surface of heater’s emitter can reach temperatures
approaching 1600ºF.
WWARNING: Do NOT touch metal parts of heater until they have
completely cooled to avoid burns, unless you are wearing protective
gear (pot holders, gloves, BBQ mittens, etc.).
• Emitter screen will become bright red due to intense heat. The color is more visible at
night.
• Burner will display tongues of blue and yellow flame. These flames should not be yellow or
produce thick black smoke, indicating an obstruction of airflow through the burners. The
flame should be blue with straight yellow tops (Figure 8).
• If excessive yellow flame is detected, turn off heater and visit MrBarBQProducts.com for
cleaning instructions or call 1-866-439-9800.
WCAUTION: If burner flame goes out during operation, immediately turn
the control knob to the “ OFF” position, LP gas tank valve “CLOSED”
and let the gas clear for 5 minutes before lighting per “Lighting”
section.
Re-lighting
Note: For your safety, the control knob cannot be turned the the “ OFF” position without first
depressing control knob in (LOW/PILOT) position and then rotating it to “ OFF.”
1. Turn control knob to “ OFF.”
2. Wait at least 5 minutes to let gas dissipate, fan with a newspaper or magazine.
3. Light per “Lighting” section.
Turning Off
1. Turn control knob clockwise to the (LOW/PILOT) position. Burner will extinguish but pilot
will remain “ON.”
2. Turn LP gas tank valve to “CLOSED.”
Note: A “poof” sound is normal as the last of the LP gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
Note: After use, some discoloration of the emitter screen is normal.
Cleaning and Care
WCAUTION:
1. All cleaning and maintenance should be done when outdoor fire pit
is cool and with the fuel supply disconnected.
2. Do NOT clean any outdoor fire pit part in a self-cleaning oven. The
extreme heat will damage the finish.
3. Do NOT enlarge valve orifices or burner ports when cleaning the
valves or burners.
Notices
1. This outdoor fire pit should be thoroughly cleaned and inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. NEVER use oven cleaner to clean any part of this outdoor fire pit.
Figure 6
KF
AA
Figure 7
KF
AA
Figure 8
Burner
Flame Slight
Yellow
Slight
Blue
Dark
Blue
10 Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase

Gas Fire Pit
Model No. GAD19104L
@
TM
Cleaning and Care (continued)
4. More frequent cleaning may be required as necessary. It is imperative that control
compartment, burners and circulating air passageways of the heater be kept clean.
5. Have the outdoor fire pit inspected annually. Any repairs should be made by a
qualified service person.
6. Inspect heater before each use.
7. Spiders and insects can create a dangerous condition that may damage the heater
or make it unsafe. Keep burner area clean of all spiders, webs and insects. Clean
burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear
away smaller particles.
8. Check heater immediately if any of the following conditions exist:
a. You smell gas in conjunction with extreme yellow tipping of burner flames.
b. Heater does not reach proper temperature.
Note: At temperatures less than 40ºF, heat output will be reduced.
c. Heater’s glow is excessively uneven.
d. Burner makes popping noises during use.
Note: A “poof” sound is normal as the last of the LP gas is burned.
9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.
10. Do NOT clean heater with combustible or corrosive cleaners. Use warm, soapy water.
11. Do NOT paint engine, engine access panel or dome.
12. After a period of storage and/or non use, check for leaks, burner obstructions and
inspect for any abrasion, wear or cuts to the hose.
13. Check under the dome and engine area periodically for any obstructions such as
spiderwebs, bird nests, etc.
Before Each Use:
1. Keep the outdoor fire pit area clear and free from any combustible materials, gasoline, and
other flammable vapors and liquids.
2. Do NOT obstruct the flow of the combustion of LP gas and the ventilation of air.
3. Keep the ventilation opening(s) of the LP gas tank area free and clear from debris.
4. Visually check the burner flames to make sure your outdoor fire pit is working properly
(Figure 5).
5. See below for proper cleaning instructions.
6. Check all gas connections for leaks.
7. Check components for any signs of damage or rust.
8. Check for obstructions of airflow to the burner. Spiders, insects and webs can clog the
burner/venturi tube. A clogged burner/venturi tube can lead to a fire.
9. If damage to any component is detected, do NOT operate until repairs are completed.
IMPORTANT BEFORE USE - HOW TO SEASON LAVA ROCK
1. Place the lava rocks into the fire pit bowl before turning on.
2. Follow the lighting instructions from the owner’s manual to light the fire pit.
3. Turn the fire pit to the highest heat.
4. Allow the lava rocks to heat at the maximum temperature for 30 minutes before enjoying fire
1111pit.
5. Keep all people and any material that could burn at least 15 feet away from the fire pit while
1111the lava rocks are being seasoned.
6. Repeat the process if your fire pit has been exposed to rain or moisture.
7. Keep your fire pit covered when not in use.
Cleaning Surfaces
1. Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water.
2. For stubborn stains, use a citrus-based cleaner and a nylon scrubbing brush.
3. Rinse clean with water.
4. Allow to air dry.
Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly
dry at all times.
WCAUTION: Do NOT submerge the control valve assembly. If the gas
control is submerged in water, do NOT use it. It must be replaced.
Maintenance
To enjoy years of outstanding performance from your heater, make sure you perform the
following maintenance activities on a regular basis:
1. Keep exterior surfaces clean.
2. Perform routine maintenance.
3. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways
clean. Signs of possible blockage include:
• Gas odor with extreme yellow tipping of flame.
• Outdoor fire pit does NOT reach the desired temperature.
• Lower burner on outdoor fire pit glow is excessively uneven.
• Lower burner on outdoor fire pit makes popping noises.
Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than
normal. Frequently check for corroded areas and repair them before operating.
TIP: Use high-quality automobile wax to help maintain the appearance of your outdoor fire pit.
Apply to exterior surfaces. Do NOT apply to burners, emitter screen or domes.
Cleaning Burner
WWARNING: All cleaning should be done when appliance is cool and
with the fuel supply disconnected per “Disconnecting LP Gas Tank.”
1. Remove the fire glass/lava rock
2. Remove all dirt/dust from the burner, igniter cover and venturi area with a small brush and/
or compressed air.
3. Visually inspect the burner for any rust or damage. If damage is found, replace necessary
parts with new from the manufacturer.
4. Clean any clogged burner ports with a stiff wire (such as an opened paper clip).
5. Carefully replace the fire glass/lava rock being cautious not to block the igniter cover.
Before Storing
1. Turn LP gas tank valve to “CLOSED.”
2. Turn control knob to the “ OFF” position.
Note: A “poof” sound is normal as the last of the gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
4. Clean all surfaces.
5. Lightly coat the burner with cooking oil to prevent excess rusting.
WCAUTION: NEVER place cover on hot outdoor fire pit.
6. If storing the outdoor fire pit indoors, cover the outdoor fire pit and store in a cool dry
location away from children and pets.
7. If storing the outdoor fire pit outdoors, cover the outdoor fire pit with a cover for protection
from the weather.
8. Store outdoor fire pit upright in an area sheltered from direct contact with inclement
weather (such as rain, sleet, hail, snow, dust, debris and high winds).
9. Place the protective cap cover on the LP tank and store the tank outdoors in a well
ventilated area out of direct sunlight.
11
®
IMPORTANT BEFORE USE
HOW TO SEASON LAVA ROCK
IMPORTANT BEFORE USE
HOW TO SEASON LAVA ROCK
1. Place the lava rocks into the fire pit bowl before turning on.
2. Follow the lighting instructions from the owner’s manual to light the fire pit.
3. Turn the fire pit to the highest heat.
4. Allow the lava rocks to heat at the maximum temperature for 30 minutes
1111before enjoying fire pit.
5. Keep all people and any material that could burn at least 15 feet away from the fire pit while
1111the lava rocks are being seasoned.
6. Repeat the process if your fire pit has been exposed to rain or moisture.
7. Keep your fire pit covered when not in use.

Specifications
Upper Burner
Certifications:
ANS Z21.97 • CSA 2.41- 2017
Rating:
Maximum 30,000 BTU/hr. input
Fuel:
Liquid Propane Gas (LP)
Tank Size:
Nominal 20 lb / 5 Gallon
Inlet Gas Supply Pressure:
Maximum – 11.00 in. W.C.
Minimum – 11.00 in. W.C.
Manifold Pressure:
11.00 in. W.C.
Safety Features:
100% Burner shut-off
Thermocouple
Manufacturer:
Mr. Bar-B-Q Products LLC
Made In:
China
Lower Burner
Certifications:
ANS Z83.26 • CSA 2.37 - 2017
Rating:
Maximum 11,000 BTU/hr. input
Heat Range:
Up to 20 foot diameter
Fuel:
Liquid Propane Gas (LP)
Tank Size:
Nominal 20 lb / 5 Gallon
Inlet Gas Supply Pressure:
Maximum – 150 PSI
Minimum – 5 PSI
Manifold Pressure:
11.00 in. W.C.
Engine:
IPP E1
Safety Features:
100% Burner shut-off
Magnetic valve
Manufacturer:
Mr. Bar-B-Q Products LLC
Made In:
China
12
Replacement Parts
For replacement, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m.,
EST,Monday - Friday.
Limited Warranty
We warrant to the original retail purchaser of this product, and to no other person, that if this
product is assembled, maintained, and operated in accordance with the printed instructions
accompanying it, then for a period of one (1) year from the date of purchase, all parts in
such product shall be free from defects in material and workmanship.
We may require reasonable proof of your date of purchase. Therefore, you should retain your
sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of
parts, which prove defective under normal use and service and which we shall determine in
its reasonable discretion upon examination to be defective. Before returning any parts, you
should contact our customer service department using the contact information listed below. If
we confirm, after examination, a defect covered by this Limited Warranty in any returned part,
and if we approve the claim, we will replace such defective part without charge. If you return
defective parts, transportation charges must be prepaid by you. We will return replacement
parts to the original retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident,
abuse, misuse, alteration, misapplication, improper installation or improper maintenance or
service by you or any third party, or failure to perform normal and routine maintenance on
the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover
damage to the finish, such as scratches, dents, discoloration, rust or other weather damage,
after purchase.
This Limited Warranty is in lieu of all other express warranties. We disclaim all warranties
for products that are purchased from sellers other than authorized retailers or distributors,
including the warranty of merchantability or the warranty of fitness for a particular purpose. WE
ALSO DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. WE
SHALL HAVE NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT,
PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. We further disclaim any implied or
express warranty of, and assumes no responsibility for, defects in workmanship caused by third
parties.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or
limitation of special, incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to everyone.
We do not authorize any person or company to assume for it any other obligation or liability in
connection with the sale, installation, use, removal, return, or replacement of its equipment, and
no such representations are binding on us.
This warranty gives you specific legal rights, and you may also have the other rights that
vary from state to state. As some states do not allow exclusions or limitations on an implied
warranty, the above exclusions and limitations may not apply.
For faster warranty service, please register your product immediately.
Please call 1-866-439-9800.
Product Registration
Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase

Gas Fire Pit
Model No. GAD19104L
@
TM
13
Troubleshooting - Upper Burner
Problem Possible Cause Prevention/Cure
Burner will not light using igniter
LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank per “Installing LP
Gas Tank,” then turn LP gas tank valve to “OPEN”
LP gas tank is low or empty Exchange, refill or replace LP gas tank
LP gas leak
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Battery needs to be changed Replace the “AA” battery (follow assembly step for inserting battery)
Electrode and burners are wet Wipe dry with cloth
Electrode cracked or broken - sparks at crack Replacement part(s) may be needed - contact Customer Care at
1-866-439-9800
Wire loose or disconnected Reconnect wire or replacement part(s) may be needed - contact Customer Care
at 1-866-439-9800
Wire is shorting (sparking) between igniter and electrode Replacement part(s) may be needed - contact Customer Care at
1-866-439-9800
Thermocouple is not operating correctly
1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section.
2. Clean area around thermocouple.
3. Connect LP gas tank per “Connect LP Gas Tank” section.
4. Relight per “Lighting” section.
5. If the outdoor fire pit is still not working, please contact Customer Care at
1-866-439-9800 for additional assistance.
Bad igniter Replacement part(s) may be needed - contact Customer Care at
1-866-439-9800
Burner will not light with match
No gas flow
Check if LP gas tank is empty
a. If empty, exchange, refill or replace LP gas tank
b. If LP gas tank is not empty, refer to “Sudden drop in gas flow or
reduced flame height” (see below)
LP gas tank is low or empty Exchange, refill or replace LP gas tank
LP gas leak
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Coupling nut and regulator not fully connected Turn the coupling nut about one-half to three-quarters additional turn until solid
stop. Tighten by hand only - do NOT use tools.
Obstruction of gas flow 1. Clear burner/venturi tube
2. Check for bent or kinked hose
Disengagement of burner to valve Re-engage burner and valve
Spider webs or insect nest in burner/venturi tube Clean burner/venturi tube
Thermocouple is not operating correctly
1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section.
2. Clean area around thermocouple.
3. Connect LP gas tank per “Connect LP Gas Tank” section.
4. Relight per “Lighting” section.
5. If the outdoor fire pit is still not working, please contact Customer Care at
1-866-439-9800 for additional assistance.
Burner ports clogged or blocked Clean burner ports
Sudden drop in gas flow or reduced flame height
Out of gas Exchange, refill or replace LP gas tank
Overfilling prevention device may have been activated
1. Turn control knob to “ OFF”
2. Wait 30 seconds and light outdoor fire pit per “Lighting” section
3. If flames are still too low, reset the overfilling prevention device:
a. Turn control knob(s) “ OFF”
b. Turn LP gas tank valve to “CLOSED”
c. Disconnect regulator
d. Turn control knobs to (HIGH)
e. Wait two minutes
f. Turn control knobs to “ OFF”
g. Reconnect regulator and leak check connections, being careful not to
fully open valve
h. Light outdoor fire pit per “Lighting” section
Irregular flame pattern, flame does not run the
full length of burner Burner ports are clogged or blocked Clean burner ports
Flame is yellow or orange
New burner may have residual manufacturing oils Burn outdoor fire pit for 15 minutes and reinspect
Spider webs or insect nest in burner/venturi tube Clean burner/venturi tube
Poor alignment of valve to burner/venturi tube Ensure burner/venturi tube is properly engaged with valve
Flame goes out
High or gusting winds Do not use outdoor fire pit in high winds
Low on LP gas Exchange, refill or replace LP gas tank
Excess flow valve tripped Refer to “Sudden drop in gas flow or reduced flame height”
Thermocouple is not operating correctly
1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section.
2. Clean area around thermocouple.
3. Connect LP gas tank per “Connect LP Gas Tank” section.
4. Relight per “Lighting” section.
5. If the outdoor fire pit is still not working, please contact Customer Care at
1-866-439-9800 for additional assistance.
Flashback (fire in venturi/burner tube(s)) Burner and/or burner/venturi tube is blocked Clean burner and/or burner/venturi tube
Flame seems to lose heat when burning in cold
weather - temperature below 50ºF
Ice has built up on the outside of the LP gas tank
because the vaporization process is too slow
1. Turn off per “Turning Off” section
2. Replace with a spare LP gas tank
3. Reconnect LP gas tank per “Installing LP Gas Tank” section
4. Follow “Checking for Leaks” section
5. Light outdoor fire pit per “Lighting” section
If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Friday.
®

Troubleshooting - Lower Burner
Problem Possible Cause Prevention/Cure
Pilot won’t light
LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank per “Installing LP Gas Tank,”
then turn LP gas tank valve to “OPEN.”
LP gas tank is low or empty Exchange, refill or replace LP gas tank
LP gas leak
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Battery needs to be changed Replace the “AA” battery (follow assembly step for inserting battery).
Igniter fails Light the heater manually with a match, per the “Lighting Instructions.” If heater lights with
a match, replace igniter - contact Customer Care at 1-866-439-9800.
Blockage in pilot or orifice Clean the pilot assembly: Download and follow the correct cleaning instructions from
MrBarBQProducts.com.
Air in gas line
1. Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or
until you smell gas
2. Turn control knob to “ OFF”
3. Wait at least 5 minutes for gas to dissipate
4. Light per “Lighting” section.
Burner won’t light
Note: Burner operates at reduced
efficiency below 40ºF (5ºC).
Control knob is NOT in an ON position Review “Lighting” section and try again
Control knob IS in an ON position Review “Lighting” section and try again
LP gas tank is low or empty Exchange, refill or replace LP gas tank
LP gas leak
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Blockage in orifice Clear blockage: Download and follow the correct cleaning instructions from
MrBarBQProducts.com.
Connection between gas valve and burner assembly is
loose
1. Turn off heater per “Turning Off” section.
2. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
3. Tighten connection.
4. Perform leak check per “Checking for Leaks” instructions.
5. Light per “Lighting” section.
Thermocouple is not operating correctly
1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section.
2. Clean area around thermocouple.
3. Connect LP gas tank per “Connect LP Gas Tank” section.
4. Relight per “Lighting” section.
5. If the outdoor fire pit is still not working, please contact Customer Care at
1-866-439-9800 for additional assistance.
Air in gas line
1. Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or
until you smell gas.
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Pilot won’t stay lit
Note: Heater operates at reduced
efficiency below 40ºF (5ºC).
Dirt built up around pilot Clean the pilot assembly: Download and follow the correct cleaning instructions from
MrBarBQProducts.com.
Connection between gas valve and pilot assembly is
loose
1. Turn off heater per “Turning Off” section.
2. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
3. Tighten connection.
4. Perform leak check per “Checking for Leaks” section.
5. Light per “Lighting” section.
Air in gas line Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until
you smell gas.
Thermocouple is not operating correctly
1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section.
2. Clean area around thermocouple.
3. Connect LP gas tank per “Connect LP Gas Tank” section.
4. Relight per “Lighting” section.
5. If the outdoor fire pit is still not working, please contact Customer Care at
1-866-439-9800 for additional assistance.
Burner won’t stay lit
Connection between gas valve and burner assembly is loose Tighten connection and perform leak check.
Thermocouple is not operating correctly
1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section.
2. Clean area around thermocouple.
3. Connect LP gas tank per “Connect LP Gas Tank” section.
4. Relight per “Lighting” section.
5. If the outdoor fire pit is still not working, please contact Customer Care at
1-866-439-9800 for additional assistance.
Blockage in burner
1. Turn off heater per “Turning Off” instructions.
2. Remove blockage and clean burner inside and outside:
Download and follow the correct cleaning instructions from MrBarBQProducts.com.
3. If the heater is still not working, replacement part(s) may be needed - contact Customer
Care at 1-866-439-9800
Burner flame is low
Note: Heater operates at reduced
efficiency below 40ºF (5ºC).
LP gas tank is low or empty Exchange, refill or replace LP gas tank
Outdoor temperature is less than 40ºF and tank is less
than 1/4 full
1. Turn off heater per “Turning Off” section.
2. Connect a full LP Gas Tank per “Connecting LP Gas Tank” section.
Supply hose is bent or kinked
1. Turn off heater per “Turning Off” section.
2. Straighten hose. If cracked obtain a new hose from the manufacturer - contact
Customer Care at 1-866-439-9800
Emitter glows uneven
Note: Bottom 1 in of emitter normally
does NOT glow.
LP gas tank is low or empty Exchange, refill or replace LP gas tank
Base is not on a level surface Place heater on a level surface
Blockage in burner
1. Turn off heater per “Turning Off” section.
2. When cool, remove blockage and clean burner inside and outside.
3. Download and follow the correct cleaning instructions from MrBarBQProducts.com.
Thick black smoke Blockage in burner
1. Turn off heater per “Turning Off” section.
2. When cool, remove blockage and clean burner inside and outside.
3. Download and follow the correct cleaning instructions from MrBarBQProducts.com.
If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Friday.
Need help? 1-866-439-9800, 8 a.m - 8 p.m., EST, Monday - Sunday.
Do not return to place of purchase 14

PELIGRO DE MONÓXIDO DE CARBONO
• Este producto puede producir monóxido de carbono, el cual
no emite ningún olor.
• Usarlo en espacios cerrados puede causar la muerte.
• Nunca use este producto en un espacio cerrado tal como
un campero, una carpa o en su casa.
·PELIGRO
N.° DE PATENTE 10,684,020
Fabricado en China para : Mr. Bar-B-Q Products LLC
10 Hub Dr., Ste 101, Melville, NY 11747 • MrBarBQProducts.com
© Mr. Bar-B-Q Products LLC
allen + roth®es una marca registrada de LF, LLC. Todos Los Derechos Reservados. GAD19104L-ES-OM-F100
FOGÓN DE GAS
@
#2592447
Modelon.º GAD19104L
Índice
Medidas de seguridad importantes .............................................................................. Página 2
Vista ampliada y tornillería ...................................................................................................... 5
Instrucciones de ensamblaje ................................................................................................... 6
Instalación del tanque de gas PL ............................................................................................. 9
Instrucciones de funcionamiento.............................................................................................10
Limpieza y cuidado ................................................................................................................11
Registro del producto..............................................................................................................12
Piezas de repuesto..................................................................................................................12
Garantía limitada ....................................................................................................................12
Especificaciones......................................................................................................................12
Solución de problemas ...........................................................................................................12
El uso y la instalación de este producto deben efectuarse conforme a las regulaciones locales. Si
no existen regulaciones locales, utilice la última edición del Código Nacional de Gas Combustible,
ANSIZ223.1, también conocido como NFPA 54, y el Código Internacional de Gas Combustible.
Si corresponde, una vez instalado este artefacto, debe presentar una puesta eléctrica a tierra
conforme a los códigos locales, o si no los hubiere, al Código Eléctrico Nacional ANSI/NFPA 70.
Para la instalación en Canadá: Estas instrucciones, si bien son generalmente aceptables, no cumplen
necesariamente con los códigos de instalación de Canadá, particularmente en cuanto a tuberías sobre y bajo
tierra. En Canadá, la instalación de este artefacto debe cumplir con los códigos locales y/o el estándar
CAN/CGA-B149.1 (código de instalación para artefactos y equipos que funcionan con gas propano).
ESTE FOLLETO DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD. LEA Y
GUARDE ESTE FOLLETO PARA REFERENCIA FUTURA.
Si está ensamblando esta unidad para otra persona, entréguele este manual para que lo lea y lo
guarde para referencia futura.
ADVERTENCIA: Este producto puede exponerlo a sustancias químicas, que incluyen monóxido
de carbono, hollín, ftalato de dioctilo, plomo y componentes de plomo, reconocidas por el estado
de California como causantes de cáncer, defectos congénitos y otros daños en el aparato
reproductivo. Lávese las manos después de manipular el producto.Para obtener más
información, visite www.P65Warnings.ca.gov.
®
TM
MANUAL DEL PROPIETARIO
ADVERTENCIA
SOLO PARA USO EN EXTERIORES.
WLa instalación y reparación deben ser realizadas por
un instalador calificado, una empresa de servicio o
el proveedor de gas.
ADVERTENCIA
PARA SU SEGURIDAD:
WSi no se sigue con precisión la información de este
manual, pueden provocarse incendios o explosiones
que produzcan daños materiales, lesiones
personales o la muerte.
W¿QUÉ HACER SI SIENTE OLOR A GAS?:
• No intente encender ningún electrodoméstico.
• NO toque ningún interruptor eléctrico ni utilice
ningún teléfono dentro del edificio.
W• Desde el teléfono de un vecino, llame
inmediatamente a su proveedor de gas.
• Siga las instrucciones del proveedor de gas.
W• Si no puede comunicarse con su proveedor de gas,
llame al Departamento de Bomberos.
WNo lo utilice para cocinar.
ADVERTENCIA
PARA SU SEGURIDAD:
WINSTALADOR: Deje este manual junto al electrodoméstico.
WCONSUMIDOR : Conserve este manual para referencia
Wfutura.
ADVERTENCIA
PARA SU SEGURIDAD:
WLa instalación, el ajuste, la alteración, la reparación o el
mantenimiento inadecuados pueden producir lesiones
o daños materiales.
WLea con atención las instrucciones de instalación,
de operación y de mantenimiento antes de instalar o
reparar este equipo.
PELIGRO
NO deje este electrodoméstico sin supervisión
mientras esté en funcionamiento.
ADVERTENCIA
PARA SU SEGURIDAD:
No almacene ni use gasolina ni otros vapores o
líquidos inflamables cerca de este ni de ningún otro
electrodoméstico.
No se deben almacenar cilindros de gasPL que
no estén conectados y en uso cerca de este ni de
ningún otro electrodoméstico.
PELIGRO
PELIGRO DE INCENDIO O EXPLOSIÓN
Si percibe olor a gas:
•Cierre el suministro de gas hacia el electrodoméstico.
• Apague cualquier llama expuesta.
•Si el olor permanece, retírese del área de inmediato.
• Después de salir del área, llame a su proveedor de
gas o al Departamento de Bomberos.
Si no sigue estas instrucciones, podría provocar
un incendio o una explosión que ocasionen daños
materiales, lesiones personales o la muerte.
Hecho con 75% de bagazo de caña
(subproducto de la caña de azúcar
respetuoso del medio ambiente)
Compuesto en un 75% de bagazo
(subproducto ecológico de pulpa
de caña de azúcar)

2
2 Fogón a gas
Modelo No. GAD19104L
®
Medidas de seguridad importantes
PELIGRO • GAS INFLAMABLE BAJO PRESIÓN.
SI SE ENCIENDEN, LAS FUGAS DE GASPL PUEDEN PROVOCAR UN INCENDIO O UNA EXPLOSIÓN Y
CAUSAR LESIONES CORPORALES GRAVES O LA MUERTE. COMUNÍQUESE CON EL PROVEEDOR DE
GASPL PARA REPARAR O ELIMINAR ESTE CILINDRO O UN CILINDRO DE GASPL NO UTILIZADO.
ADVERTENCIA
•SOLO PARA USO EN EXTERIORES.*
NO UTILICE NI ALMACENE EL CILINDRO EN EDIFICIOS, GARAJES NI ÁREAS CERRADAS.
• Conozca el olor del gasPL. Si oye, ve o huele una fuga
de gasPL, aleje inmediatamente a todas las personas
del cilindro y llame al Departamento de Bomberos. No
intente repararlo.
• Adviértale a su proveedor de gasPL lo siguiente:
Que se asegure de que no haya aire atrapado en el
cilindro antes de llenarlo por primera vez..
Que se asegure de no llenar demasiado el cilindro.
Que se asegure de verificar la fecha de
recalificación del cilindro.
• El gasPL es más pesado que el aire y puede depositarse
en lugares bajos a medida que se dispersa.
• El contacto con el contenido líquido del cilindro puede
causar quemaduras por frío en la piel.
• No permita que los niños manipulen ni jueguen con el
cilindro.
• Cuando el cilindro no esté conectado ni en uso,
mantenga la válvula cerrada. Los artefactos autónomos
se limitarán a un cilindro de 30lb (13,6kg) de capacidad
o menos.
• No use, almacene ni transporte el cilindro a lugares
en los que pueda quedar expuesto a altas temperaturas.
La válvula de descarga de presión puede abrirse y dejar
escapar una gran cantidad de gas inflamable.
• Cuando lo transporte, mantenga el cilindro asegurado en
una posición vertical con la válvula del cilindro cerrada.
CUANDO LO CONECTE PARA SU USO:
• Use este producto exclusivamente como lo estipulan las
regulaciones vigentes.
• Lea y siga las instrucciones del fabricante.
• Consulte las instrucciones del fabricante con respecto a la
conexión del cilindro proporcionada con su artefacto.
• Asegúrese de que la ventilación del regulador no apunte
hacia arriba.
• Cierre todas las válvulas del artefacto.
• No utilice un fósforo ni una llama abierta para detectar fugas
de gas. Aplique agua jabonosa en las áreas marcadas con
una “X”. Abra la válvula del tanque. Si aparecen burbujas,
cierre la válvula y deje que un técnico en mantenimiento de
artefactos a gasPL realice las reparaciones necesarias.
Antes de encender el artefacto, revise también las válvulas y
las conexiones para asegurarse de que no presenten fugas.
• Encienda el artefacto de acuerdo con las instrucciones del
fabricante.
• Cuando el artefacto no esté en uso, mantenga la válvula del
cilindro cerrada.
ADVERTENCIA:
NO RETIRE, DAÑE NI DESTRUYA ESTA ETIQUETA
*EXCEPTO LO AUTORIZADO POR ANSI/NFPA 58.
PELIGRO. No almacene un cilindro de gasPL de reserva debajo o cerca de una parrilla u otras fuentes de calor.
NUNCA llene un cilindro de gasPL a más del 80% de su capacidad, se podría producir un incendio que provoque lesiones graves o la muerte.
Indicador del nivel de
líquido
Válvula de liberación de presión
Manivela de la válvula del tanque
Cilindro
Punto de conexión
@
TM

3 3
Medidas de seguridad importantes
WNO use este fogón para exteriores sin haber leído por completo el
manual del propietario.
WEste artefacto es solo para uso en exteriores y NO se debe usar en
edificios, garajes ni en ninguna otra área cerrada.
WNO opere, encienda ni use este artefacto a menos de diezpies (3,05m)
de distancia de paredes, estructuras o edificios.
WSolo para uso residencial. Este fogón para exteriores NO es para uso
comercial.
WNO use este fogón para exteriores para calefaccionar interiores. Las
emanaciones TÓXICAS de monóxido de carbono pueden acumularse y
causar asfixia.
WEste fogón para exteriores está certificado para utilizarse en forma
segura en los EstadosUnidos y Canadá solamente. NO lo modifique para
usarlo en otro lugar. Cualquier modificación tendrá como resultado un
riesgo para la seguridad y anulará la garantía.
WPara quienes viven en departamentos: consulte con el administrador
acerca de los requisitos y códigos de incendio para usar un fogón
para exteriores de gas propano líquido (PL) en su complejo de
departamentos. Utilícelo en el exterior, en la planta baja, a una distancia
de 10pies (3,05m) de cualquier estructura, en caso de estar permitido.
NO lo utilice debajo de balcones ni sobre estos.
WEste fogón para exteriores, tal como se produce en fábrica, se usa solo
con gasPL. Es peligroso convertir o intentar convertir este fogón para
exteriores para usarlo con gas natural, ya que puede producir lesiones
corporales y anulará la garantía.
WCaracterísticas del gas PL:
a. El gas propano líquido es inflamable y peligroso si se manipula de
manera incorrecta. Tenga en cuenta las características antes de
usar cualquier producto de gasPL.
b. El gas PL es explosivo bajo presión, es más denso que el aire y se
deposita o acumula en áreas bajas.
c. El gas propano en su estado natural no tiene olor. Para su seguridad,
se le ha agregado un odorizante que huele como una col en mal
estado.
d. El contacto con el gas propano puede causar quemaduras por frío
en la piel.
WNecesita un tanque de gasPL para usarse. Solo se pueden usar tanques
marcados con “propano”.
a. El tanque de gas PL debe estar fabricado y marcado según las
especificaciones para tanques de gas PL del Departamento de
Transporte de los EE. UU. (D.O.T., por sus siglas en inglés) o la Norma
para cilindros, esferas y tubos para el transporte de mercancías
peligrosas y la Comisión, CAN/CSA-B339, según corresponda.
b. El tanque de gasPL se debe adaptar para la extracción de vapores.
c. El tanque de gasPL debe tener un dispositivo de prevención de
sobrellenado (OPD, por sus siglas en inglés) homologado y una
conexión QCCI o TipoI (CGA810) para tanques de gasPL.
d. El tanque de gasPL debe tener un anillo para proteger la válvula del
tanque.
e. No use un tanque de gas PL si el cuerpo, la válvula, el anillo o la
base están dañados.
f. Los tanques de gas PL abollados u oxidados pueden ser peligrosos y
su proveedor de gas propano debe revisarlos antes de su uso.
g. No debe dejar caer el tanque de gasPL ni manipularlo bruscamente.
h. Los tanques deben almacenarse en el exterior, fuera del alcance
de los niños, y no deben almacenarse en edificios, garajes ni
en ninguna otra área cerrada. El tanque de gas PL nunca debe
almacenarse en lugares en que las temperaturas puedan superar
los 125 °F (51,7 ºC).
i. NO introduzca herramientas ni objetos extraños en la salida de la
válvula ni en la válvula de descarga de seguridad, ya que puede
dañar la válvula y ocasionar una fuga. Las fugas de propano pueden
provocar una explosión, incendio, lesiones personales graves o la
muerte.
j. No guarde un tanque de gas PL en un automóvil expuesto a altas
temperaturas ni en el maletero. El calor hace aumentar la presión
del gas, lo que puede abrir la válvula de descarga y producir un
escape de gas.
k. Coloque la tapa antipolvo en la salida de la válvula del cilindro
cuando no esté en uso. Solo instale el tipo de tapa antipolvo que se
proporciona con la válvula del cilindro en la salida de la válvula del
cilindro. Otros tipos de tapas o tapones pueden causar una fuga de
propano.
l. NO almacene un tanque de gas PL de repuesto debajo o cerca de
este artefacto.
m. Nunca llene el cilindro más allá del 80% de su capacidad.
n. Si no sigue las instrucciones anteriores al pie de la letra, podría
producirse un incendio y ocasionar lesiones graves o daños
materiales.
WSe revisaron todas las conexiones hechas en la fábrica del fogón para
exteriores para confirmar que no presenten fugas. Vuelva a revisar
todas las conexiones como se describe en la sección "Instrucciones de
funcionamiento", ya que en el transporte se pueden aflojar.
WRevise si hay fugas incluso si otra persona ensambló la unidad para usted.
WNO lo use si existe una fuga de gas. Las fugas de gas podrían provocar
un incendio o una explosión.
WSiga todas las instrucciones de la sección "Detección de fugas" antes
de usar el artefacto. Para evitar incendios o explosiones mientras
realiza la prueba de fugas:
a. Siempre realice una prueba de fuga antes de encender este fogón
para exteriores y cada vez que se conecte el tanque para su uso.
b. No fume cerca del producto. NO use ni permita que haya otras
fuentes de ignición en el área mientras realiza una prueba de fugas.
c. Realice la prueba de fuga en exteriores, en un área bien ventilad.
d. NO utilice fósforos, encendedores ni llamas para detectar la
existencia de fugas.
e. El consumo de alcohol o medicamentos recetados o sin receta
puede disminuir la capacidad del consumidor para ensamblar o
usar este artefacto de manera segura y correcta.
f. Los malos olores fuertes, resfríos, congestión de los senos paranasales,
etc. pueden impedir la detección del propano. Sea cuidadoso y utilice el
sentido común cuando realice pruebas de fugas.
g. NO use este fogón para exteriores hasta que se hayan corregido
todas las fugas. Si no puede detener una fuga, desconecte el
suministro de gas propano. Llame a un técnico de artefactos de gas
o a su proveedor local de gas PL.
WNO almacene ni utilice gasolina ni otros vapores o líquidos inflamables
a menos de 25pies (7,62m) de distancia de este artefacto.
WNO utilice el artefacto en un entorno explosivo. No debe haber materiales
combustibles, gasolina ni otros vapores o líquidos inflamables cerca del
área donde se va a utilizar el fogón para exteriores.
WLos niños NO deben manipular este fogón para exteriores.
WEste fogón para exteriores NO debe usarse en vehículos recreativos ni
en botes.
WNO lo conecte a un suministro de gas remoto.
WNunca intente conectar este fogón para exteriores al sistema de gasPL
autocontenido de un remolque para camping, casa rodante o casa.
WSiempre cumpla con todos los códigos locales, estatales y nacionales
correspondientes al utilizar el producto. Comuníquese con el
Departamento de Bomberos local para obtener información sobre
quemas en exteriores.
WCuando use este fogón para exteriores, tome las mismas precauciones
que tomaría con cualquier fuego expuesto.
WEn este fogón para exteriores, NO queme combustibles sólidos,
como los siguientes: madera, briquetas de carbón, carbón de leña,
leños fabricados, madera arrojada por el mar, basura, hojas, papel,
cartones, madera contrachapada, madera pintada, teñida o tratada a
presión.
WPELIGRO: No seguir los avisos de peligro, las advertencias y las precauciones de este manual podría causar lesiones personales graves, la muerte o
incendios o explosiones que causen daños materiales.
WADVERTENCIAS :
¿Necesita ayuda? Llame al1-866-439-9800 de lunes a domingos, de 8a.m. a 8p.m., hora estándar del Este.
No devuelva este producto al lugar donde lo compró

4 ®
Medidas de seguridad importantes (continuación)
WEs esencial que mantenga limpios el compartimiento de la válvula,
los quemadores y los pasajes de circulación de aire del fogón para
exteriores. Inspeccione el fogón para exteriores antes de cada uso.
WNO use este fogón para exteriores hasta que esté COMPLETAMENTE
ensamblado y todas las piezas estén ajustadas y apretadas con firmeza.
WNO use este fogón para exteriores cerca de automóviles, camiones,
camionetas o vehículos recreativos.
WNO use este fogón para exteriores debajo de construcciones aéreas o
construcciones de materiales combustibles sin protección. Evite usarlo
cerca o debajo de árboles y arbustos sobresalientes.
WColoque siempre este fogón para exteriores sobre una superficie
rígida, nivelada y no combustible, como concreto, rocas o piedras. Una
superficie de asfalto podría no ser apta para este objetivo.
WNO use este fogón para exteriores para cocinar.
WNO use este artefacto si alguna de sus piezas estuvo sumergida en
agua. Llame de inmediato a un técnico en mantenimiento calificado
para que inspeccione el artefacto y reemplace cualquier pieza, sistema
de control o control de gas que haya estado bajo agua.
WNO use ropas combustibles u holgadas durante el uso del fogón para
exteriores.
WNO lo utilice cuando haya mucho viento.
WNo se apoye sobre este fogón para exteriores cuando lo encienda o esté
funcionando.
WNO use este fogón para exteriores a menos que el quemador esté fijo en
su lugar.
WMantenga todos los cables eléctricos lejos de este fogón para exteriores
cuando esté en uso.
WCuando esté en funcionamiento, ciertas áreas de este fogón para
exteriores estarán demasiado calientes para el tacto. NO toque las
superficies calientes hasta que se hayan enfriado completamente
(espere unos 45minutos) para evitar quemaduras, a menos que utilice
equipo de protección (como manoplas para horno con aislante, guantes
o manoplas resistentes al calor).
WNO deje el fogón para exteriores encendido y sin supervisión,
especialmente si hay niños o mascotas cerca.
WTanto niños como adultos deben estar informados sobre los peligros de
la alta temperatura de la superficie y deben permanecer alejados para
evitar quemaduras o incendio de la ropa.
WSe debe supervisar atentamente a los niños pequeños cuando se
encuentren en el área del artefacto.
WNO cuelgue ni coloque vestimenta ni otros materiales inflamables sobre
el artefacto ni cerca de este.
WCualquier protector u otro dispositivo de protección que se hayan
retirado para dar mantenimiento al artefacto deben volver a colocarse
antes de hacerlo funcionar.
WSi corresponde, debe quitarse la cubierta de protección cuando el
quemador esté funcionando.
WNO intente mover el fogón para exteriores mientras lo esté usando.
Permita que el fogón para exteriores se enfríe antes de moverlo o
almacenarlo.
WEste fogón para exteriores se debe limpiar e inspeccionar
minuciosamente en forma periódica. Limpie e inspeccione la manguera
antes de cada uso del artefacto. Si hay evidencia de abrasión, desgaste,
cortes o fugas, debe reemplazar la manguera antes de utilizar el
artefacto.
WUn técnico calificado debe inspeccionar este fogón para exteriores al
menos una vez al año. Es posible que se requiera una limpieza más
seguida según la frecuencia de uso. NO lo use hasta que todas las
piezas se hayan reparado o reemplazado.
WUse solo el ensamble del regulador y la manguera que se incluyen. Use
solo el ensamble del regulador y la manguera de repuesto especificado
por Mr. Bar-B-Q Products LLC.
WUtilice únicamente piezas autorizadas por la fábrica de Mr. Barb-B-Q
Products LLC. El uso de piezas que no estén autorizadas por la fábrica
puede ser peligroso y anulará la garantía.
WUtilice únicamente las rocas de vidrio para fuego o rocas de lava
autorizadas por la fábrica de Mr. Barb-B-Q Products LLC. El uso de rocas
de vidrio para fuego o rocas de lava que no estén autorizadas por la
fábrica puede ser peligroso y anulará la garantía.
WNO use este artefacto sin antes leer las "Instrucciones de
funcionamiento" en este manual.
WPuede almacenar en interiores este fogón para exteriores solo si
desconecta y retira el tanque del fogón y lo almacena apropiadamente
en exteriores.
WNO intente desconectar el regulador de gas del tanque ni de ninguna
otra conexión de gas mientras use el fogón para exteriores.
WSi el fogón para exteriores no está en uso, se debe cerrar el gas desde
el tanque de suministro.
WPRECAUCIÓN: Se debe usar solamente el regulador de presión de gas
incluido con este electrodoméstico. El regulador está ajustado para una
presión de salida de 11 pulg. (27,94 cm) de columna de agua.
WLa presión mínima de entrada de gas para este fogón para exteriores es
de 11pulg. (27,94cm) de columna de agua, con el objetivo de ajustar la
entrada.
WLa presión máxima del gas de admisión para este fogón para exteriores
es de una columna de agua de 11pulg. (27,94cm) de columna de agua.
WAntes de probar la presión, cierre la válvula del tanque de gasPL y
desconéctela del regulador de gas. La prueba del sistema de tuberías
de suministro de gas debe resultar en presiones iguales o menores que
1/2psi (3,5kPa).
WNO se siente ni se pare sobre la repisa ni sobre ninguna otra parte de
este artefacto.
WNO lance nada dentro del fogón cuando la unidad esté en
funcionamiento.
WLas rocas de vidrio o rocas de lava alcanzan temperaturas muy altas.
Mantenga a los niños y a las mascotas a una distancia segura de este
artefacto.
WCuando se calientan, las rocas de vidrio para fuego o rocas de lava se
pueden reventar.
WLa abertura del anillo del tanque debe dar hacia el lado de la puerta
para que el acceso sea fácil.
WNO almacene ningún material combustible en el compartimiento base.
WUse guantes de protección cuando ensamble este producto.
WNO una las piezas a la fuerza, ya que podría provocar heridas
personales o daños al producto.
WSi no sigue las instrucciones anteriores al pie de la letra, podría ocasionar
lesiones graves, muerte o daños materiales.
Fogón a gas
Modelo No. GAD19104L
@
TM

Herramientas necesarias para el ensamblaje (no incluidas)
Destornillador Phillips #2 1 pza
Paquete de tornillería 58-24-397
ATornillo Cabezal en cruz con revestimiento en níquel negro M5x12 22 pzas
BTornillo Cabezal en cruz con revestimiento en níquel negro M6x12 1 pza
CTornillo Cabezal en cruz con revestimiento en níquel negro M5X25 4 pzas
DTornillo Cabezal en cruz con revestimiento en níquel negro M4X8 1 pza
EBatería AA Batería AA de 1,5 V 1 pza
Vista ampliada
Se vende por separado
17
1Rocas de vidrio para
fuego negras GLS-BLK
2Accesorio para mesa 58-24-521
Fogón/Unidad de
calefacción* 58-24-522
Tapa de la batería* 58-23-897
Perilla de control (2)* 58-23-139
Ensamblaje de manguera
y regulador* 58-24-181
Gancho de encendido 58-24-387
Panel inferior (3) 58-24-523
6Puerta 58-24-524
7Perilla de la puerta* 58-24-391
8Base* 58-24-389
Perno de retención del
tanque de gasPL* 58-23-149
Barra de retención del
tanque de gasPL 58-24-388
Pata A (2) 58-24-392
Pata B 58-24-393
Pata C 58-24-394
Imán* 58-23-804
15 Pie (4)* 58-23-147
16 Cubierta 58-24-525
17
Rocas de lava (no se
requiere y se vende por
separado)**
55-05-833
* Preensamblada
W**PRECAUCIÓN: Utilice
únicamente las rocas de vidrio
para fuego o rocas de lava
autorizadas por la fábrica de
Mr.Bar-B-QProductsLLC. El
uso de rocas de vidrio para
fuego o rocas de lava que no
estén autorizadas por la fábrica
puede ser peligroso y anulará la
garantía.
3.1
3.2
3.3
4
5
9
10
11
12
13
14
3
Lista de piezas
ADVERTENCIA
Cuando se calientan, las rocas de
lava pueden reaccionar rompíendose
y arrojando fragmentos de roca.
Asegúrese de preparar las rocas de
lava a una temperatura alta antes de
usarlas para evitar posibles lesiones o
daños personales.
TENER EN CUENTA ANTES DE USAR:
CONSULTE CÓMO PREPARAR LAS
ROCAS DE LAVA EN LA PÁGINA.
CONSULTE CÓMO PREPARAR LAS
ROCAS DE LAVA EN LA PÁGINA12.
1
7
2
8
5
6
13
3
9
5
5
10
16
11
11
12
14
15
15 15
3
4
3.1
3.2
3.3
¿Necesita ayuda? Llame al1-866-439-9800 de lunes a domingos, de 8a.m. a 8p.m., hora estándar del Este.
No devuelva este producto al lugar donde lo compró
Las baterías no recargables no deben recargarse.
Las baterías deben insertarse con la polaridad correcta.
Las baterías agotadas deben retirarse del producto.
DONOTDISPOSEOFBATTERIESIN FIRE.LAS BATERÍAS PUEDEN
EXPLOTAR O TENER FUGAS.

Fogón a gas
Modelo No. GAD19104L
@
TM
Instrucciones de ensamblaje
3
Coloque las patas
WPRECAUCIÓN: Se necesitarán dos (2) personas para voltear
la chimenea para exteriores.
WPRECAUCIÓN: Para evitar rasguños, elija una superficie
suave sin grietas ni rendijas.
Nota: No apriete los tornillos por completo hasta el paso5.
Ax 8
2
Voltee el fogón para exteriores
WPRECAUCIÓN: Se requieren dos(2)personas para voltear el
fogón para exteriores.
WPRECAUCIÓN: Para evitar los rasguños, elija una superficie
lisa, sin grietas ni aberturas.
11
11
13
12 A
6 ®
1
NO DEVUELVA ESTE PRODUCTO AL LUGAR DONDE LO
COMPRÓ .
Para obtener ayuda, llame gratis al 1-866-439-9800.Tenga a mano el
manual de usuario y el número de modelo para referencias.
Nota: El número de modelo está impreso en una etiqueta, que se encuentra
en la puerta interior, en la parte posterior o lateral del ensamblaje de la base.
Consejos de ensamblaje :
1. Seleccione el área donde ensamblará este producto. Para
proteger a los componentes, elija una superficie lisa, sin
grietas ni aberturas .
2. Despliegue todas las piezas .
3. Primero apriete a mano todos las conexiones de la tornillería.
Luego, antes de completar cada paso, vuelva al principio
y apriete todos los tornillos firme y completamente. Tenga
cuidado de no apretar demasiado. Eso podría dañar las
superficies o falsear las roscas.
4. Para obtener mejores resultados, complete cada paso en el
orden presentado .
Para completar el ensamblaje, necesitará:
• (1) Solución para detección de fugas (las instrucciones acerca
de cómo elaborar la solución están incluidas en la Sección
“Instrucciones de funcionamiento” de este manual).
• (1) Tanque de parrilla a gasPL llenado con precisión con una
conexión de válvula con rosca externa AcmeTipo1 (tamaño
de parrilla estándar) (no incluido).
El ensamblaje normal dura, aproximadamente, una hora .
WPRECAUCIÓN: Se requieren dos (2) personas para
el ensamblaje .
• ADVERTENCIA: No colocar las piezas de
acuerdo con estos diagramas o no usar
solo las piezas aprobadas específicamente
con este artefacto puede ocasionar daños
materiales o lesiones personales .
4
Coloque los paneles laterales y posteriores
Nota: Fije los tornillos inferiores antes de fijar los tornillos superiores. No apriete los
tornillos por completo hasta el paso5.
Ax 12
A