LG MULTI V LRNN Series User manual

System
Heat Pump Indoor Unit
INSTALLATION MANUAL
LG
MODELS: LRNN, LRNV-SV Series
Type: Art Cool-Wide
website http://www.lgservice.com
IMPORTANT
• Please read this Installation manual completely before
installing the product.
• Installation work must be performed in accordance with
the national wiring standards by authorized personnel
only.
• Please retain this Installation manual for future reference
after reading it thoroughly.

2Indoor Unit
Art Cool Wide Type Indoor Unit Installation Manual
TABLE OF CONTENTS
❏ Installation guide map
❏Four type "A" screws & plastic
anchors
❏Connecting cable
❏Pipes: Gas side
Liquid side
(Refer to Product Data)
❏Insulation materials
❏Additional drain pipe
❏Two type "B" screws
❏Level gauge
❏Screw driver
❏Electric drill
❏Hole core drill
❏Horizontal meter
❏Flaring tool set
❏Specified torque wrenches
(different depending on model No.)
❏Spanner .......Half union
❏A glass of water
❏Screw driver
❏Hexagonal wrench
❏Gas-leak detector
❏Vacuum pump
❏Gauge manifold
❏Owner's manual
❏Thermometer
Installation Parts Provided....3
Safety Precautions .................4
Installation
Selection of the best location 7
Preparing work for
installation ..............................8
Fixing the installation
plate on the wall and fixing
indoor unit...............................9
Connection of piping............11
Drain piping..........................12
Front panel assembly ..........13
Installation of remote
control...................................15
Drain pipe work....................16
Installation Requirements Required Parts Required Tools

Installation Manual 3
Installation Parts Provided
Installation Parts Provided
Name
Quantity
Shape
1 EA
Installation panel
1 set
Securing screws
2 EA
M4 x 12L
Name
Quantity
Shape
Insulating tape Clamp
4 EA
(Other)
• Owner's manual
• Installation manual
for gas pipe
for liquid pipe
Insulation for
fitting
1 set

4Indoor Unit
Safety Precautions
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be followed.
■Be sure to read before installing the air conditioner.
■Be sure to observe the cautions specified here as they include important items related to safety.
■Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the
following indications.
■Meanings of symbols used in this manual are as shown below.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
Be sure not to do.
Be sure to follow the instruction.
■Installation
Do not use a defective or under-
rated circuit breaker. Use this
appliance on a dedicated circuit.
• There is risk of fire or electric shock.
For electrical work, contact the
dealer, seller, a qualified electri-
cian, or an Authorized Service
Center.
• Do not disassemble or repair the
product. There is risk of fire or elec-
tric shock.
Always ground the product.
• There is risk of fire or electric shock.
Install the panel and the cover
of control box securely.
• There is risk of fire or electric shock.
Always install a dedicated cir-
cuit and breaker.
• Improper wiring or installation may
cause fire or electric shock
Use the correctly rated breaker
or fuse.
• There is risk of fire or electric shock.

Installation Manual 5
Safety Precautions
■Operation
Do not modify or extend the
power cable.
• There is risk of fire or electric shock.
Do not let the air conditioner
run for a long time when the
humidity is very high and a door
or a window is left open.
• Moisture may condense and wet or
damage furniture.
Be cautious when unpacking
and installing the product.
• Sharp edges could cause injury. Be
especially careful of the case edges
and the fins on the condenser and
evaporator.
For installation, always contact
the dealer or an Authorized
Service Center.
• There is risk of fire, electric shock,
explosion, or injury.
Do not install the product on a
defective installation stand.
• It may cause injury, accident, or
damage to the product.
Be sure the installation area
does not deteriorate with age.
• If the base collapses, the air condi-
tioner could fall with it, causing prop-
erty damage, product failure, and
personal injury.
Do not store or use flammable gas or combustibles near the product.
• There is risk of fire or failure of product.
Gasolin

6Indoor Unit
Safety Precautions
Always check for gas (refriger-
ant) leakage after installation or
repair of product.
• Low refrigerant levels may cause
failure of product.
Install the drain hose to ensure
that water is drained away prop-
erly.
• A bad connection may cause water
leakage.
Keep level even when installing
the product.
• To avoid vibration or water leakage.
Do not install the product where
the noise or hot air from the out-
door unit could damage the
neighborhoods.
• It may cause a problem for your
neighbors.
Use two or more people to lift
and transport the product.
• Avoid personal injury.
Do not install the product where
it will be exposed to sea wind
(salt spray) directly.
• It may cause corrosion on the product.
Corrosion, particularly on the con-
denser and evaporator fins, could
cause product malfunction or inefficient
operation.
90˚
■Installation

Installation Manual 7
Installation
Read completely, then follow step by step.
Installation
Selection of the best location
CAUTION
: In case that the unit is installed near the sea, the installation parts may be corrod-
ed by salt. The installation parts (and the unit) should be taken by appropriate anti-
corrosion measures.
•Do not have any heat or steam near the unit.
•Select a place where there are no obstacles in front of the unit.
•Make sure that condensation drainage can be conveniently routed away.
•Do not install near a doorway.
•Ensure that the space around the left and right of the unit is more than 50cm. The unit should be installed as high on the
wall as possible, allowing a minimum of 10cm from ceiling.
•Use a stud finder to locate studs to prevent unnecessary damage to the wall.
More than 10cm
More than 50cm
More than 2m More than 50cm

8Indoor Unit
Installation
Preparing Work for Installation
The wall you select should be strong and solid enough
to prevent vibration
1) Open panel front
•First, pull the grille bottom, then remove screws
(2 pieces), and close grille bottom again.
•The moment of lifting the both lower parts of panel
front, you can hear sound this panel came out. In
this time panel front is separated.
•After pulling down this panel a bit, separate con-
necting wire from product.
2) Cover pipe and cover side remove
•Remove two screws(for fixing cover pipe)
•Pull up the cover side of desired connecting direc-
tion, then cover side is separated.
•In case connecting direction is left or right, path
through the hole of cover side.
(When path through the hole, take care of burr.)
When connecting pipe path through rear
wall, don’t remove the hole.
3) Drain hose junction
•Remove the rubber stopple of desired drain direc-
tion.
•As the following picture, insert drain hose in the han-
dle of drain pan, and join drain hose and connecting
hose.
NOTICE
Panel Front
Connector
rubber cap
Only one
desiring direction
Connecting
part
Adhesive
Drain
hose
Pipe hole
Side cover

Installation Manual 9
Installation
Fixing the Installation Plate on the Wall and fixing indoor Unit
1. Drilling the center hole with ø3.5mm drill
and fix the plate with screw or hail.
2. Always mount the installation plate
horizontally by aligning the making-off line
by means of the thread and a level.
3. Confirm the horizontal and fixed state of the plate.
4. Confim the piping hole position.
240mm
60mm
240mm
60mm
Center hole
Installation plate
Weight
Thread
Type "A"
screw
Making-off line
Weight
Thread
Making-off line

10 Indoor Unit
Installation
CAUTION : Installation Information
(For right piping)
• Bad case
■
Following bending type from left to right could cause prob-
lem of pipe damage.
• Good case
For right piping. Follow the instruction below.
■ Press on the upper side of clamp and
unfold the tubing to downward slowly.
•Drilling the hole slightly tilted.
•Piping direction
70mm
70mm
Indoor Outdoor
5~7mm
Pipes
Drain pipe
Right
Left
Right rear
Left rear

Installation Manual 11
Installation
Connection of Piping
•Preparing the indoor unit's piping and drain hose for
installation through the wall.
1) Route the indoor tubing and the drain hose in the
direction of rear left or right.
2) Tape the tubing, drain hose, and the connecting
cable. Be sure that the drain hose is located at the
lowest side of the bundle. Locating at the upper
side can cause drain pan to overflow inside the
unit.
If the drain hose is routed inside the room,
insulate the hose with an insulation material* so that drip-
ping from "sweating"(condensation) will not damage furni-
ture or floors.
*Foamed polyethylene or equivalent is recommended.
3) Connecting the pipings to the indoor unit and drain
hose to drain pipe.
•Align the center of the pipes and sufficiently tighten
the flare nut by hand.
•Tighten the flare nut with a wrench.
•When extending the drain hose at the indoor unit,
install the drain pipe.
4) Wrap the insulation material around the connect-
ing portion.
•Overlap the connection pipe insulation material and
the indoor unit pipe insulation material. Bind them
together with vinyl tape so that there is no gap.
NOTICE
Connecting
cable
Gas side piping
Liquid side piping Drain hose
Loop
Indoor unit tubing Flare nut Pipes
Wrench
Indoor unit tubing
Open-end wrench (fixed)
Connection pipe
Flare nut
GAS LIQUID
Capacity
(Btu/h)
12,000, 18,000 Ø15.88[6.6kg.m] Ø9.52[4.2kg.m]
Pipe Size[Torque]
Vinyl tape(narrow)
Adhesive
Drain pipe
Indoor unit drain hose
Plastic bands Insulation material

12 Indoor Unit
Installation
Drain Piping
•Wrap the area which accommodates the rear piping
housing section with vinyl tape.
•Bundle the piping and drain hose together by wrap-
ping them with vinyl tape enough to cover where
they fit into the rear piping housing section.
Vinyl tape(narrow)
Connection
pipe
Connecting cable
Vinyl tape
(wide) Wrap with vinyl tape
Indoor
unit pipe
Pipe
Wrap with vinyl tape
Drain hose
Pipe
Vinyl tape(wide)
1) To check the drainage.
•Pour a glass of water on the evaporator.
•Ensure the water flows through the drain hose of
the indoor unit without any leakage and goes out
the drain exit.
2) Drain piping
•The drain hose should point downward for easy
drain flow.
•Do not make drain piping.
Downward slope
Do not raise Accumulated
drain water
Tip of drain hose
dipped in water
Air
Waving
Water
leakage
Water
leakage Ditch
Less than
50mm gap
Water
leakage

Installation Manual 13
Installation
Front Panel Assembly
1) First, check the side cover assembly exactly.
2) Assemble connecting lead wire with controller,
fix the upper part of panel front, and match the
lower part of panel front
3) Drive three screws.
Panel Front
Connector

14 Indoor Unit
Installation
•Connect the cable to the indoor unit by connecting the wires to the terminals on the control board
individually according to the outdoor unit connection. (Ensure that the color of the wires of the outdoor unit
and the terminal No. are the same as those of the indoor unit.)
The earth wire should be longer than the common wires.
•When installing, refer to the wiring
diagram on the Control Box of
Indoor Unit.
•When installing, refer to the wiring
diagram on the Control Cover
Inside Outdoor Unit.
Terminal Block in Indoor
1(L) 2(N) 3 4
INDOOR POWER INPUT
Terminal Block in Outdoor
ABC D Vcc
CAUTION
•The above wiring diagram is subject to change without notice.
•Be sure to connect wires according to the wiring diagram.
•Connect the wires firmly not to be pulled out easily.
•Connect the wires according to color codes by referring to the wiring diagram.
CAUTION
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method of
wiring, be guided by the wiring diagram posted on the inside of control cover.
2) The screw which fastens the wiring in the casing of electrical fittings is liable to come loose from vibra-
tions to which the unit is subjected during the course of transportation. Check them and make sure that
they are all tightly fastened. (If they are loose, it could cause burn-out of the wires.)
3) Specification of power source.
4) Confirm that electrical capacity is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage marked on the
name plate.
6) Confirm that the cable thickness is as specified in the power source specification.
(Particularly note the relation between cable length and thickness.)
7) Always install an earth leakage circuit breaker in a wet or moist area.
8) The following would be caused by voltage drop.
•Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the normal
function of the overload.
9) The means for disconnection from a power
supply shall be incorporated in the fixed wiring and have an air gap contact separation of at least 3mm
in each active(phase) conductors.

Installation Manual 15
Installation
1. Remove the battery cover from the remote control.
•Slide the cover according to the arrow direction.
2. Insert the two batteries.
•Be sure that the (+) and (-) directions are correct.
•Be sure that both batteries are new.
3. Re-attach the cover.
•Slide it back into position.
HOW TO MOUNT ONTO A WALL
HOW TO INSERT BATTERIES
•Do not use rechargeable batteries,
such batteries differ from standard dry
cells in shape, dimensions, and per-
formance.
•Romove the batteries from the remote
control if the air conditioner is not
going to be used for some long time.
Installation of Remote Control

16 Indoor Unit
Installation
1) Drain pipe gradient and support
a) The drain pipe must be fitted at a gradient of at least 1/100.
The drain pipe should be as short as possible and free from airlocks.
2) Drain trap
Fit any indoor unit whose drain pipe connection is subjected to negative pressure, with a drain trap.
a) Rig the drain trap shown in the drawing below.
b) Provide one trap per unit. A single trap for converging units will prove ineffective.
c) Rig the trap to allow for future changing.
b) Suspension bolts should be used th support long stretches of drain pipe in order to ensure that a
gradient of 1/100 is maintained (PVC pipe should not be bent)
Spacing of supports for horizontal piping
c) The length of pipe laid horizontally should be kept a minimum.
Gradient of least 1 / 100
(1cm / 1m)
Indoor unit
Indoor unit
H
H
Indoor unit
Plug
Indoor unit
Plug
Class Norminal diameter Spacing
Rigid PVC pipe 25~40 mm 1.0 m or less
Drain Pipe Work

Installation Manual 17
Installation
3) Ground drain piping
a) It is standard work practice to make connections to the main pipe from above. The pipe down from the
combination should be as large as possible.
4) Use of an auxiliary drain hose(flexible)
a) If the drain pan made of polystyrene foam is used then an auxiliary drain hose(flexible) is also essential, a
flexible drain hose permits the drain socket and drain pipe to be connected without difficulty and prevents
any undue strain being placed on he drain pan.
❈Important points
- The drain pipe should be at least equal in size to that of the indoor unit.
- The drain pipe is thermally insulated to prevent the formation of condensation inside the pipe.
- The drain up mechanism should be fitted before the indoor unit is installed and when the electricity has
been connected some water should be added to the drain pan so that the drain pump checks to see that it
is functioning correctly.
- All connections should be secure. (Special care is needed with PVC pipe)
- Insulate auxiliary drain hose with thermal insulation band.
b) The pipe work should be kept as short as possible and the number of indoor units per group be kept to a
minimum.
Face piping
downward
Vent pipe
Face the vent pipe mouth downward to keep
foreign matter from penetrating the system
Metal clamp
Drain pan Metal clamp
Thermal insulation(bend area)
Auxiliary drain hose Thermal insulation (drain pipe area)

P/No.: 3828A23004F Printed in Korea
After reading this manual, keep it in a place easily accessible to the user for future reference.