LG RU-17LZ22 User manual

- 2 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc.,
to be sure the set is safe to operate without damage of
electrical shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
http://www.wjel.net

- 3 -
SPECIFICATIONS.................................................................4
DESCRIPTION OF CONTROLS...........................................5
ADJUSTMENT INSTRUCTIONS ..........................................7
TROUBLESHOOTING ........................................................10
PRINTED CIRCUIT BOARD ...............................................11
BLOCK DIAGRAM...............................................................14
EXPLODED VIEW...............................................................16
EXPLODED VIEW PARTS LIST.........................................17
REPLACEMENT PARTS LIST............................................18
SCHEMATIC DIAGRAM..........................................................
TABLE OF CONTENTS
http://www.wjel.net

- 4 -
SPECIFICATIONS
MODEL
Width (inches)
Height (inches)
Depth (inches)
Weight (pounds)
Power Requirement
Television System
Television Channel
Television Screen
Power Consumption
External Antenna Impedance
Audio Output
Adapter (DC Power)
RU-17LZ20/22
18.6
15.7
7.4
15.4
DC15V/4.5A
NTSC
VHF : 2 ~ 13, UHF : 14 ~ 69, Cable : 01 ~ 125
LCD Panel
See the back of the set
75 Ω
5 W + 5 W
In: AC 100-240V ~ 1.6A-0.7A, 50/60Hz
Out: DC 15V, 4.5A
* For use only with Model No. SAD7015SE
AC Adapter, manufactured by H & E CO., LTD.
http://www.wjel.net

- 5 -
DESCRIPTION OF CONTROLS
Controls & Connection Options
Controls & Connection Options
on/off tv/video menu enter vol ch
MONO DPM
SAP
STEREO
ST
On/Off Button
Remote Control Sensor
DPM Indicator
SAP Indicator
Mono Indicator
Power/Standby Indicator
Glows red in Standby mode,
Glows green when the TV is turned on.
Stereo Indicator
TV/Video Button
Menu Button
Enter Button
Volume Button
Channel Button
R
S-VIDEO VIDEO L / MONO AUDIO
IN 2
ANT IN
+75 Ω
COMPONENT(480i/480p/720p/1080i)
PC
SOUND
VIDEO IN
DVD/DTV IN
AUDIO
VIDEO
P
R
P
B
Y
AUDIO(MONO)
DC IN (15V)
L R LR
PC INPUT
Headphone Jack
S-Video Input
Video Input
Audio Input
DC 15V Input
DVD/DTV Input
(Component (480i/480p/720p/1080p), Audio)
Audio / Video Input
PC Sound Input
PC Input
Antenna Input
http://www.wjel.net

- 6 -
-When using the remote control, aim it at the remote control sensor on the TV.
powermute
tv/video
multimedia
mts
fcr
ch
ch
vol enter
123
456
789
0
vol
exit
menu
audio
piparc cc
video
pip input flashbkposition
pip swap sleepsize
still
scan ch
MUTE
Switches the sound on or off.
PIP
POSITION
PIP INPUT
SIZE
PIP SWAP
STILL
SCAN
CH (DD/ EE)
ENTER
CH DD/ EE(Channel button)
VOL FF/ GG(Volume button)
POWER
MTS
EXIT
MENU
MULTIMEDIA
Selects: TV, Component, or RGB-
PC mode.
VIDEO
CC
FLASHBK
Press the FLASHBK button to
return to the last channel you were
watching.
SLEEP
AUDIO
ARC
TV/VIDEO
Selects: TV, Video 1,Video 2, S-
Video,Component, or RGB-PC
mode.
FCR
NUMBER buttons
Remote Control Key Functions
Remote Control Key Functions
DESCRIPTION OF CONTROLS
http://www.wjel.net

- 7 -
1. Application Object
This instruction is for the application to the LCD TV.
2. Notes
(1) This set uses an adapter, so connect the adapter and the
set correctly before adjustment.
(2) Adjustments must be performed in the correct sequence.
(3) Adjustments must be performed in an enviorment of
25!5cC (68-85 degrees F) of temperature and 65!10% of
relative humidity.
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz in adjusting.
(5) The set must be operated for 15 minutes prior to adjustment.
[‘Heat Run’ must be performed with the full white signal or TV
noise signal.
3. PC Input Mode Adjustment
3-1. Required Test Equipment
(1) A pattern generator; Gray pattern of 16 tones with angle
outline in the quadrilateral (MSPG-925LTH)
(2) An adjustment Remote.
3-2. Preparation for Adjustment
(1) Perform ‘Heat Run’ for more than 15 minutes in white
pattern.
(2) Connect the signal of pattern generator with LCD TV.
3-3. Auto Gray Adjustment
(1) Apply the gray signal XGA(1024X768) 16 tones from a
signal generatror.
(2) In Service menu mode, adjust the Auto gray from 0 to 1 by
using Vol(+) button.
ADJUSTMENT INSTRUCTIONS
http://www.wjel.net

- 8 -
ADJUSTMENT INSTRUCTIONS
4. Position Adjustment
Mode
H_Display
V_Display
V_Frequency
H_Total
H_Blanking
H_Sync
H_Polarity
H_Vp
H_Fp
H-Freq[KHz]
/Clk[MHz]
V_Total
V_Blanking
V_Sync
V_Polarity
V_Bp
V_Fp
VGA-60
640
480
60
800
160
96
NEG.
48
16
31.469
25.175
525
45
2
NEG
33
10
VGA-67
640
480
67
864
224
64
NEG.
96
64
35.0
30.24
525
45
3
NEG
39
3
VGA-75
640
480
75
840
200
64
NEG
120
16
37.5
31.5
500
20
3
NEG
16
1
VGA-85
640
480
82
832
192
56
NEG
80
56
43.269
36.0
509
29
3
NEG
25
1
SVGA-56
800
600
56
1024
224
72
POS
128
24
35.156
36.0
62.5
25
2
POS
22
1
SVGA-60
800
600
60
1056
256
128
POS
88
40
37.879
40.0
628
28
4
POS
23
1
SVGA-72
800
600
72
1040
240
120
POS
64
56
48.077
50.0
666
66
6
POS
23
37
Mode
H_Display
V_Display
V_Frequency
H_Total
H_Blanking
H_Sync
H_Polarity
H_Vp
H_Fp
H-Freq[KHz]
/Clk[MHz]
V_Total
V_Blanking
V_Sync
V_Polarity
V_Bp
V_Fp
SVGA-75
800
600
75
1056
256
80
POS
160
16
46.875
49.5
625
25
3
POS
21
1
SVGA-
85800
600
85
1048
248
64
POS
152
32
53.674
56.25
631
31
3
POS
27
1
XGA-60
1024
768
60
1344
320
136
NEG
136
160
48.363
65.0
806
38
6
NEG
29
3
XGA-70
1024
768
70
1328
304
136
NEG
144
24
56.476
75.0
806
38
6
NEG
29
3
XGA-75
1024
768
75
1312
288
96
POS
176
16
60.023
78.75
800
32
3
POS
28
1
XGA-85
1024
768
82
1376
352
96
POS
208
48
68.677
84.997
808
40
3
POS
36
1
WXGA-50
1280
768
50
1648
368
128
NEG
184
56
39.518
65.125
791
23
7
POS
15
1
WXGA-60
1280
768
60
1680
400
136
NEG
200
64
47.693
80.125
795
27
7
POS
19
1
http://www.wjel.net

- 9 -
ADJUSTMENT INSTRUCTIONS
5. EDID (The Extended Display Identification Data)
EDID Table
00
10
20
30
40
50
60
70
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00
00
14
81
01
01
26
00
FF
0B
50
40
01
01
30
32
FF
01
54
81
01
01
18
55
FF
01
BF
80
01
01
88
1E
FF
78
E8
01
01
01
36
46
FF
1F
80
01
01
01
00
0D
FF
17
31
10
01
01
0E
00
00
70
59
0E
01
01
C3
0A
30
E8
3B
01
F9
01
10
20
E5
C3
D9
01
15
01
00
20
D7
A0
45
01
01
64
00
20
3A
A3
59
01
01
19
1E
20
01
54
61
01
01
00
00
20
00
4C
59
01
01
40
00
20
00
97
71
01
01
41
00
00
00
24
59
01
01
00
FD
C8
http://www.wjel.net

- 10 -
1 No sound Defective Reset IC of IC604. 1) Check volume and speaker.
- Speaker Defective MSP3411 of IC601. - Sound comes out only when being inputted into Audio
- Earphone Defective B+(8V,5V) of IC603. L/R.
2) Check after replacing IC604.
3) Replace IC601.
4) Check and replace B+ of IC603.
2 Video color beat noise Earphone shield case being touched.
Check the mould of shield and SJ209, Replace shield case.
Soldering IC301 and IC510. Re-soldering
1 No screen Input error of inverter connector 1) Bend the pin legs of P1 connector -> recheck them
2) Check and repair F804.
P704 connector slipping out 1) Check and fix P704 connector
2) Check and fix the components at P704 LCD module
and at main board.
3) Check Pin21.
Cracked components and Check and repair tuner board and main board
soldering at tuner board
2 Dark screen 1) Defective LCD lamp 1) Replace the LCD lamp
2) Defective inverter 2) Replace the inverter
3) Input error for inverter 3) Check the connector input.
1. General Features
2. PC Mode
No. Symptom Cause Check Point
No. Symptom Cause Check Point
Check Point
1 Screen noise Clock or phase being 1) Resettig is needed according to the video card of each
not able to be adjusted. PC.
2) Horizontal noise : adjust phase until no horizontal
noise occurres.
3) Vertical noise : adjust clock in menu until no vertical
noise occurres.
2 Screen position error Screen position error 1) Activate the Auto Configure in the Menu.
horizontally or vertically 2) Adjust horizontal and vertical position until the screen
displayes normally.
3 Color beat noise Soldering D-SUB Jack of JA202 Recheck and repair JA202,IC202
and IC202.
3. TV and external input
No. Symptom Cause
TROUBLESHOOTING
http://www.wjel.net

- 17 -
112 6306V17001A LCD MODULE,LC171W03-A4 LG PHILPS TFT COLOR TFT LCD MODULE
120 6400GKTX01A SPEAKER,FULLRANGE F1527C-6428 (GENERAL) 8OHM 7/12W 83DB
300 3091V00535L CABINET ASSEMBLY,RU-17LZ22 STEREO ML027C FOR CANADA
3091V00535H CABINET ASSEMBLY,RU-17LZ22.AAPLKZ
310 5020V00798C BUTTON,CONTROL RU-17LZ22 ABS, HF-380 8KEY
311 4810V00836G BRACKET,CONTROL RU-17LZ22 ML027C HIPS 40AF
330 4950V00157A METAL,STAND NON HINGE ASSY_15LA60
340 4810V00777D BRACKET,STAND RU-15LA61 ML012C HIPS 60HR FRONT
350 4810V00778D BRACKET,STAND RU-15LA61 ML012C HIPS 60HR REAR
360 4810V00776C BRACKET,DECO RU-15LA61 ML012C ABS, HF-380
370 4810V00779C BRACKET,STAND RU-15LA61 ML012C ABS, HF-380 BASE
380 4950V00135A METAL,STAND NON BASE, 15LA60
400 3809V00371K BACK COVER ASSEMBLY,RU-17LZ22 NON
401 3550V00335B COVER,REAR AV RU-17LZ22 ABS, HF-380
500 3141VMNQ35A CHASSIS ASSEMBLY,MAIN ML027C
521 4950V00168A METAL,SHIELD NON NON
522 4950V00151B METAL,SHIELD ET .
523 3500V00067F BOARD,AV RU-17LZ22 ML027C .
524 4950V00167A METAL,FRAME NON NON
530 6633VA0003R INVERTER ASSEMBLY,15V NON ECT 6LAMP CIU11-K004
540 6871VSMW58A PCB ASSEMBLY,SUB ML027C SIDE A/V
541 4810V00838G BRACKET,SIDE AV RU-17LZ22 ML027C HIPS 40AF
550 6871VSMW59A PCB ASSEMBLY,SUB WINDO ML027C INDEX ASSY
560 6871VSMW57F PCB ASSEMBLY,SUB CONT ML027C RU-17LZ22
EXPLODED VIEW PARTS LIST
No. PART NO. DESCRIPTION
http://www.wjel.net

- 18 -
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q3
Q370
Q371
Q4
Q605
Q606
Q701
Q801
Q802
C51
C52
C53
C54
C55
C56
D1
D803
D804
D810
D811
ZD101
ZD201
ZD202
ZD203
ZD204
ZD205
ZD206
ZD207
ZD212
ZD213
ZD214
ZD215
ZD216
ZD225
ZD370
C107
C109
C112
C113
C1527
C1532
C1544
C1545
C1599
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DD181009AB
0DD100009AM
0DD181009AB
0DR340009AA
0DR340009AA
0DZ330009BA
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00248A
0CE108DD618
0CE106DK618
0CE476DF618
0CE107DF618
0CE107DF618
0CE107DF618
0CE476DF618
0CE107DD618
0CE107DD618
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
KDS181 85V 300MA
EU1ZV(1) TP SANKEN
KDS181 85V 300MA
MBRS340 40V 3A 80A 2MA
MBRS340 40V 3A 80A 2MA
ZENERS,HZT33
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,UDZS TE17 5.1B
ZENERS,RLZ8.2BTE11
1000UF STD 10V M
10UF STD 50V M
47UF STD 16V M
100UF STD 16V M
100UF STD 16V M
100UF STD 16V M
47UF STD 16V M
100UF STD 10V M
100UF STD 10V M
LOCA. NO PART NO DESCRIPTION
IC1
IC2
IC201
IC202
IC3
IC301
IC401
IC501
IC502
IC503
IC504
IC510
IC555
IC600
IC601
IC603
IC604
IC701
IC702
IC806
IC807
IC808
IC888
IC901
IC915
IC950
IC951
IC954
IC955
IC804
IC805
Q104
Q107
Q201
Q202
Q203
Q2301
Q2302
Q2303
Q2304
Q2305
Q2306
Q2307
Q2308
0IZZVC0070A
0IFA754207A
0IAL242110A
0IMCRFA022A
0IAL241610B
0IIT323000E
0IIN298003A
0IMCRPW001B
0IMCRTI020A
0IMCRAL006A
0IMCRTI002A
0IMCRGN001B
0IMCRPU001A
0IMCRTI022D
0IMCRMN007A
0IMCRFA008A
0IKE704200J
0IMCRTH001A
0IMCRNS007B
0IMCRNS007D
0IMCRNS007C
0IMCRNS007C
0IMCRNS007A
0IMCRMI006A
0IMMRHY033A
0IMCRAD002A
0IMCRNS007E
0IMCRMZ001A
0IMCRMZ001A
0TFVI80005A
0TF492509AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
M37136EFSP DIP 52P
KA75420ZTA 3P,TO92 TP 4.2V
AT24C2110SI2.5 8P,SOP TP 1K
74F14SC 14P SCHMITT TRIGGER IC
AT24C16A10PI2.7 8PIN
VPC3230D C5 80P VIDEO PROCESSOR
COPY TE28F800B3TA90 48TSOP BK 8M
PW181(133MHZ) 352PBGA
TLC7733ID 8P SOP R/TP DTYPE 3.3V
AT24C16AN10SI2.7 8P
SN74HCT32D 16P
FLI2310BC 208P DIGITAL VIDEO
P2781A08SR 8 PIN R/TP EMI REDUCTION
TPA3004D2 48P 9WSTEREO AUDIO AMP
MSP3421G QA B8 V3 80P VIRTUAL DOLBY
KA78M05RTM 2P DPAK
KIA7042AF SOT89 TP 4.2V
THC63LVDM83R 56P TRANSMITTER IC
LM2941S 5P TO263 R/TP 12V
LMS1587 CS 1.5V 3P TO263
LMS1587CSADJ 3P TO263 R/TP 1.5V
LMS1587CSADJ 3P TO263 R/TP 1.5V
LM2940S 8V 3P TO263
M52758FP 36PIN, R/TP PLL IC
HY57V643220C(L)T6 86P 64M
AD9883A 80P DIGITAL BOARD
LMS1587CS3.3 3P TO263 R/TP 3.3V
MP1583DN 8P DCDC CONVERTER
MP1583DN 8P DCDC CONVERTER
SI4963DY R/TP SO8 20V 6.2A
SI4925DY 30V 6.1A SO8
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
IC
TRANSISTOR
RUN DATE : 2003.8.12
For Capacitors & Resistors,
the 2nd and 3rd digits in the
P/No. designate;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
DIODE
CAPACITOR
http://www.wjel.net

- 19 -
LOCA. NO PART NO DESCRIPTION
C19
C2
C2
C216
C219
C220
C2201
C2202
C2211
C301
C303
C305
C31
C315
C316
C328
C332
C333
C336
C337
C338
C341
C343
C347
C349
C351
C353
C546
C583
C584
C585
C59
C6
C60
C603
C61
C613
C615
C616
C617
C619
C62
C620
C621
C622
C624
C626
C627
C628
C63
C630
0CE106DF618
0CE107DF618
0CE687DD618
0CE106DF618
0CE106DF618
0CE106DF618
0CK105DF64A
0CK105DF64A
0CE225DK618
0CK224DF56A
0CK224DF56A
0CK224DF56A
0CE105DK618
0CK224DF56A
0CE107DD618
0CE106DF618
0CE476DF618
0CE107DF618
0CK224DF56A
0CE226DF618
0CE107DF618
0CK224DF56A
0CE476DF618
0CE105CK636
0CE105CK636
0CE105CK636
0CE105CK636
0CE107DF618
0CE107DF618
0CE107DF618
0CE107DF618
0CK105DF64A
0CE107DF618
0CK105DF64A
0CE476DF618
0CK105DF64A
0CE107DF618
0CE107DD618
0CE106DF618
0CE106DF618
0CE335DK618
0CK105DF64A
0CE477DF618
0CK224DF56A
0CK224DF56A
0CK224DF56A
0CK224DF56A
0CK224DF56A
0CK224DF56A
0CK105DF64A
0CE107DF618
10UF STD 16V M
100UF STD 16V M
680UF STD 10V 20%
10UF STD 16V M
10UF STD 16V M
10UF STD 16V M
1UF 2012 16V 20%
1UF 2012 16V 20%
2.2UF STD 50V 20%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
1UF STD 50V M
220000PF 2012 16V 10%
100UF STD 10V M
10UF STD 16V M
47UF STD 16V M
100UF STD 16V M
220000PF 2012 16V 10%
22UF STD 16V M
100UF STD 16V M
220000PF 2012 16V 10%
47UF STD 16V M
1UF SHL,SD 50V M
1UF SHL,SD 50V M
1UF SHL,SD 50V M
1UF SHL,SD 50V M
100UF STD 16V M
100UF STD 16V M
100UF STD 16V M
100UF STD 16V M
1UF 2012 16V 20%
100UF STD 16V M
1UF 2012 16V 20%
47UF STD 16V M
1UF 2012 16V 20%
100UF STD 16V M
100UF STD 10V M
10UF STD 16V M
10UF STD 16V M
3.3UF STD 50V 20%
1UF 2012 16V 20%
470UF STD 16V 20%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
1UF 2012 16V 20%
100UF STD 16V M
LOCA. NO PART NO DESCRIPTION
C634
C643
C644
C645
C650
C658
C660
C662
C665
C666
C668
C677
C682
C683
C684
C711
C730
C777
C801
C802
C803
C804
C805
C806
C815
C819
C820
C822
C823
C825
C826
C831
C832
C834
C835
C836
C837
C839
C839
C888
C888
C902
C902
C902A
C923
C924
C925
C926
C927
C928
C941
0CE107DF618
0CE476DK618
0CK224DF56A
0CK224DF56A
0CE227DH618
0CN475FH67A
0CN475FH67A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CN475FH67A
0CN475FH67A
0CN475FH67A
0CE107DF618
0CE107DH618
0CE477DF618
0CE476DK618
0CE477DF618
0CE477DH618
0CE477DF618
0CE477DF618
0CE477DF618
0CE477DH618
0CE106DF618
0CE226DF618
0CE107DH618
0CE227DH618
0CE477DH618
0CE477DH618
0CE477DD618
0CE477DD618
0CE477DD618
0CE477DD618
0CE477DD618
0CE477DD618
0CE477DD618
0CE477DF618
0CE477DH618
0CE477DD618
0CE107DF618
0CE477DD618
0CE227DD618
0CE476DF618
0CE476DF618
0CE476DF618
0CE476DF618
0CE476DF618
0CE476DF618
0CE106DK618
100UF STD 16V M
47UF STD 50V M
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220UF STD 25V M
4.7UF 3225 25V 20%
4.7UF 3225 25V 20%
1UF 2012 16V 20%
1UF 2012 16V 20%
1UF 2012 16V 20%
1UF 2012 16V 20%
1UF 2012 16V 20%
4.7UF 3225 25V 20%
4.7UF 3225 25V 20%
4.7UF 3225 25V 20%
100UF STD 16V M
100UF STD 25V M
470UF STD 16V 20%
47UF STD 50V M
470UF STD 16V 20%
470UF STD 25V M
470UF STD 16V 20%
470UF STD 16V 20%
470UF STD 16V 20%
470UF STD 25V M
10UF STD 16V M
22UF STD 16V M
100UF STD 25V M
220UF STD 25V M
470UF STD 25V M
470UF STD 25V M
470UF STD 10V M
470UF STD 10V M
470UF STD 10V M
470UF STD 10V M
470UF STD 10V M
470UF STD 10V M
470UF STD 10V M
470UF STD 16V 20%
470UF STD 25V M
470UF STD 10V M
100UF STD 16V M
470UF STD 10V M
220UF STD 10V M
47UF STD 16V M
47UF STD 16V M
47UF STD 16V M
47UF STD 16V M
47UF STD 16V M
47UF STD 16V M
10UF STD 50V M
REPLACEMENT PARTS LIST
http://www.wjel.net

- 20 -
LOCA. NO PART NO DESCRIPTION
C942
C956
C962
C987
C988
C989
C991
F801
F802
F803
F804
F804
F805
F805
JA204
JA205
JA206
JA2201
JA801
SJ205
SJ209
L101
L2206
L2207
L652
L653
L654
L655
L801
L804
T801
JA202
P2002
P2202
P2203
P2301
R2202
R2209
RA401
RA402
RA403
0CE107DF618
0CK823DK56A
0CE107DF618
0CE476DF618
0CE476DF618
0CE476DF618
0CK105DF64A
0FS4001B84B
0FS4001B84B
0FT2001A86B
0FS2501B84B
0FT2001A86B
0FS2501B84B
0FT2001A86B
6612VCH003B
380-336E
380-336F
6613V00008F
6612VAH001C
6612VJH008D
6613V00004P
0LA0102K139
0LA0472K119
0LA0472K119
6140VR0008A
6140VR0008A
6140VR0008A
6140VR0008A
6140VR0008B
6140VR0008B
6170VMCA57B
6630G15E215
6631V20037C
387-A05E
6631V20014K
6631V20010E
0RD1200H609
0RD1200H609
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
100UF STD 16V M
82000PF 2012 50V 10%
100UF STD 16V M
47UF STD 16V M
47UF STD 16V M
47UF STD 16V M
1UF 2012 16V 20%
FUSE,SLOW BLOW 0FS 4000MA 250V
FUSE,SLOW BLOW 0FS 4000MA 250V
FUSE,SLOW BLOW 2000MA 125V
FUSE,SLOW BLOW 2500MA 250V
FUSE,SLOW BLOW 2000MA 125V
FUSE,SLOW BLOW 2500MA 250V
FUSE,SLOW BLOW 2000MA 125V
JACK,PHONE PEJ012C
JACK,RCA WA6013E 1P
JACK,RCA WA6013E 1P
JACK ASSY,PMJ014F E/P(ST)+SVHS+3P
JACK,PHONE DC003 4PIN POWER
JACK,RCA PJ6063D DVD IN 3P
JACK ASSY,PJ6054P 3P
INDUCTOR,10UH K
INDUCTOR,47UH K
INDUCTOR,47UH K
COIL,SLF12575T330M4R7 33UH
COIL,SLF12575T330M4R7 33UH
COIL,SLF12575T330M4R7 33UH
COIL,SLF12575T330M4R7 33UH
COIL,SLF12575T150M3R2 15UH
COIL,SLF12575T150M3R2 15UH
TRANSFORMER,SMPS[COIL] EPC1716 15UH
CONNECTOR,DSUB 15P 2.29MM
CONNECTOR ASSEMBLY,7P 2.0MM
CONNECTOR ASSEMBLY,5P 2.5MM
CONNECTOR ASSEMBLY,12P 2.0MM
CONNECTOR ASSEMBLY,8P 2.0MM
120 OHM 1/2 W 5.00%
120 OHM 1/2 W 5.00%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
LOCA. NO PART NO DESCRIPTION
RA404
RA405
RA406
RA407
RA451
RA452
RA453
RA454
RA502
RA511
RA512
RA525
RA525
RA526
RA526
RA701
RA702
RA703
RA704
RA705
RA706
RA707
SW2007
SW2008
SW2009
SW2010
SW2011
SW2012
SW2013
SW2014
SW501
SW502
L102
L103
L1955
L1956
L1957
L1958
L2
L205
L206
L214
L215
L2201
L2202
L2206
L2207
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001D
0RRZVTA001A
0RRZVTA001D
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
140-313B
140-313B
140-313B
140-313B
140-313B
140-313B
140-313B
140-313B
6600VR1004A
6600VR1004A
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001A
6210TCE001A
6210TCE001A
6210TCE001A
6210TCE001A
6210TCE001A
6210TCE001A
6210TCE001A
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
22 OHM 1 / 16 W 1608 5%
MNR14E0AJ101 R OHM 100 OHM 5%
22 OHM 1 / 16 W 1608 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
MNR14E0AJ101 R OHM 100 OHM 5%
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT 2LEAD 160G(TA)
SWITCH,TACT SKHMPW 5P
SWITCH,TACT SKHMPW 5P
FILTER,EMC HH1M3216501
FILTER,EMC HH1M3216501
FILTER,EMC HH1M3216501
FILTER,EMC HH1M3216501
FILTER,EMC HH1M3216501
FILTER,EMC HH1M3216501
FILTER,EMC HH1M3216501
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
FILTER,EMC HB1S2012080JT
SWITCH
REPLACEMENT PARTS LIST
JACK
FUSE
COIL & TRANSFORMER
CONNECTOR
RESISTOR
FILTER & CRYSTAL
http://www.wjel.net
Table of contents
Other LG LCD TV manuals