LG 42LA613V.AEK User manual

User Guide
This is a 「User Guide」 installed on the TV.
The contents of this guide are subject to change without prior notice for quality
improvement.

GP2

 



GP2
eng
❐To set favourite programmes
SETTINGS ➾ SETUP ➙ Programme Edit
1 Select the channel you want.
2 Press the FAV button to select Favourite Group and then OK.
✎You can check your favourite channels by pressing the LIST button on the
remote control.
❐To use Favourite
Press the FAV button.
You can only view the channels you set as favourites.

GP2
eng
Press GUIDE button.
[In Digital mode only]
Obtains information about programmes and airtime. Checks the broadcasting
time of the desired programme and schedule viewing.

GP2
eng
❐Automatically Setting Up Programme
SETTINGS ➾ SETUP ➙Auto Tuning
Automatically tunes the programmes.
1 Select Country where the TV is used. Programme settings change depending
on the country you choose.
2 Initiate Auto Tuning.
3 Select Input Source of your choice.
4 Set Auto Tuning following screen instructions.
✎If Input Source is not connected properly, programme registration may not
work.
✎Auto Tuning only finds programmes that are currently broadcasting.
✎If Lock System is turned on, a pop-up window will appear asking for
password.

GP2
eng
❓Cable DTV Setting option
When searching for programmes using FULL setting it can take a long time. The
following values are needed in order to search all available programmes quickly
and correctly. The commonly used values are provided as “default”.
• Frequency : Enter a user-defined frequency.
• Symbol rate : Enter a user-defined symbol rate (Symbol rate: Speed at which
a device such as modem sends symbols to a channel).
• Modulation : Enter a user-defined modulation. (Modulation: Loading of audio
or video signals onto carrier).
• Network ID : Unique identifier allocated for each user.
• Start Frequency : Enter a user-defined start frequency range.
• End Frequency : Enter a user-defined end frequency range.

GP2
eng
❓Satellite Setting Option
• Satellite : Select your desired Satellite.
• LNB Frequency : [Depending on country] Select one value from 9750/10600,
9750/10750, 9750, 10600,10750, 5150, MDU1, MDU2, MDU3, MDU4, MDU5.
If you select 9750/10600, 9750/10750(MHz), 22KHz Tone is disabled. If you
cannot find the LNB frequency value from the list, select User and manually
enter the frequency.
• Transponder : Select the transponder you want to tune.
• 22KHz Tone : When using 22KHz Tone switch, select A or B. If you use 22KHz
Tone, Unicable and Motor Type are disabled.
• LNB Power : To enable the power supply for the LNB, select On. If you select
Off, Motor Type is disabled.

GP2
eng
• DiSEqC : When using DiSEqC, select one option from A~D/ToneA~B. If you
use DiSEqC, Unicable and Motor Type are disabled.
• Unicable Settings : Select On to use Unicable and set the Unicable in the
Unicable Setting menu. When Unicable is enabled, 22KHz Tone, DiSEqC,
Motor Type are disabled.
• Motor Type : Select Motor Type to use Motor and set the Motor in the Motor
Setting menu. When Motor is enabled, 22KHz Tone, DiSEqC, Unicable are
disabled.
✎If you set satellite to others, you must add a transponder using Manual
Tuning.
✎When selecting 22KHz Tone and DiSEqc, you must connect them in the same
position as displayed on the OSD.
✎If you delete a Satellite, all programmes stored in the Satellite are deleted.

GP2
eng
❓Motor Setting Option
• DiSEqC 1.2 : Control motor to change satellite dish position.
Drive Direction : Select the direction in which you want to move the motor.
Drive Mode : Two modes are available: Step and Continuous.
-Step: The motor moves based on the value you enter (from 1 to 128).
-Continuous: The motor moves continuously until you press the Stop.
Test TP : Select the test TP you want to tune.
Set Limit : Set the motor movement to east or west to have the motor move
only within the direction set.
-On: You can limit the movement to the current direction by selecting the
West/East.
-Off: You can cancel the limit you set.

GP2
eng
Go To Zero: You can move the motor to Zero
Store: You can save the motor’s current direction.
• USALS : Set your current location(Longitude/Latitude).