LG 42LF650V User manual

OWNER’S MANUAL
Safety and Reference
www.lg.com
Please read this manual carefully before operating your
set and retain it for future reference.
P/NO : MFL68702214 (1502-REV01)
Printed in Korea
*MFL68702214*

2
ENGLISH
Safety instructions
Please read these safety
precautions carefully before using
the product.
WARNING
Do not place theTV and/or remote control in
the following environments:
• A location exposed to direct sunlight
• An area with high humidity such as a
bathroom
• Near any heat source such as stoves and
other devices that produce heat
• Near kitchen counters or humidiers where
they can easily be exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in re, electric
shock, malfunction or product deformation.
Do not place the product where it might be
exposed to dust. This may cause a re hazard.
Mains Plug is theTV connecting/disconnecting
device to AC mains electric supply.This plug
must remain readily attached and operable
whenTV is in use.
Do not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or
wipe dust o. You may be electrocuted due to
excess moisture.
Make sure to connect Mains cable to compliant
AC mains socket with Grounded earth pin.
(Except for devices which are not grounded
on earth.) Otherwise possibility you may be
electrocuted or injured.
Insert power cable plug completely into wall
socket otherwise if not secured completely into
socket, re ignition may break out.
Ensure the power cord does not come into
contact with hot objects such as a heater. This
may cause a re or an electric shock hazard.
Do not place a heavy object, or the product
itself, on power cables.
Otherwise, this may result in re or electric
shock.

ENGLISH
3
Bend antenna cable between inside and
outside building to prevent rain from owing
in. This may cause water damaged inside the
Product and could give an electric shock.
When mountingTV onto wall make sure to
neatly install and isolate cabling from rear of
TV as to not create possibility of electric shock /
re hazard.
Do not plug too many electrical devices into a
single multiple electrical outlet. Otherwise, this
may result in re due to over-heating.
Do not drop the product or let it fall over when
connecting external devices. Otherwise, this
may result in injury or damage to the product.
Desiccant
Keep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause
suocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the
TV.
Otherwise, theTV may fall over, which may
cause serious injury.
Dispose of used batteries carefully to ensure
that a small child does not consume them.
Please seek Doctor- Medical Attention
immediately if child consumes batteries.
Do not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not touch
the power cable right after plugging into the
wall input terminal.You may be electrocuted.
(Depending on model)

4
ENGLISH
Do not put or store inammable substances
near the product.There is a danger of
combustion/explosion or re due to careless
handling of the inammable substances.
Do not drop metallic objects such as coins,
hair pins, chopsticks or wire into the product,
or inammable objects such as paper and
matches. Children must pay particular
attention. Electrical shock, re or injury can
occur. If a foreign object is dropped into the
product, unplug the power cord and contact the
service centre.
Do not spray water on the product or scrub
with an inammable substance (thinner or
benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects
to fall into the unit, and do not drop anything
onto the screen.You may be injured or the
product can be damaged.
Never touch this product or antenna during a
thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there
is leakage of gas, open the windows and
ventilate. It may cause a re or a burn by a
spark.
Do not disassemble, repair or modify the
product at your own discretion. Fire or electric
shock accident can occur.
Contact the service centre for check, calibration
or repair.
If any of the following occur, unplug the
product immediately and contact your local
service centre.
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange
smell
This may result in re or electric shock.

ENGLISH
5
Unplug theTV from AC mains wall socket if you
do not intend to use theTV for a long period of
time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric
leakage/shock/re.
Apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could
be exposed to oil or oil mist.This may damage
the product and cause it to fall.
If water enters or comes into contact withTV,
AC adapter or power cord please disconnect
the power cord and contact service centre
immediately. Otherwise ,this may result in
electric shock or re.
Only use an authorized AC adapter and power
cord approved by LG Electronics. Otherwise, this
may result in re, electric shock, malfunction or
product deformation.
Never Disassemble the AC adapter or power
cord.
This may result in re or electric shock.
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an
outside antenna and power lines to keep the
former from touching the latter even when the
antenna falls.This may cause an electric shock.
Do not install the product on places such as
unstable shelves or inclined surfaces. Also avoid
places where there is vibration or where the
product cannot be fully supported. Otherwise,
the product may fall or ip over, which may
cause injury or damage to the product.
If you install theTV on a stand, you need to
take actions to prevent the product from
overturning. Otherwise, the product may fall
over, which may cause injury.

6
ENGLISH
If you intend to mount the product to a wall,
attachVESA standard mounting interface
(optional parts) to the back of the product.
When you install the set to use the wall
mounting bracket (optional parts), x it
carefully so as not to drop.
Only use the attachments / accessories specied
by the manufacturer.
When installing the antenna, consult with a
qualied service technician. If not installed by
a qualied technician, this may create a re
hazard or an electric shock hazard.
We recommend that you maintain a distance
of at least 2 to 7 times the diagonal screen size
when watchingTV. If you watchTV for a long
period of time, this may cause blurred vision.
Only use the specied type of battery. This
could cause damage to the remote control.
Do not mix new batteries with old batteries.
This may cause the batteries to overheat and
leak.
Batteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight , open replace and electric heaters .
Do not place non-rechargeable batteries in
charging device.
Make sure there are no objects between the
remote control and its sensor.
Signal from Remote Control can be interrupted
due to external/internal lighting eg Sunlight,
uorescent lighting. If this occurs turn o
lighting or darken viewing area.
When connecting external devices such as
video game consoles, make sure the connecting
cables are long enough. Otherwise, the product
may fall over, which may cause injury or
damage the product.
Do not turn the product On/O by plugging-
in or unplugging the power plug to the wall
outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an
electric shock.

ENGLISH
7
Please follow the installation instructions
below to prevent the product from overheating.
• The distance between the product and the
wall should be more than 10cm.
• Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
• Do not install the product on a carpet or
cushion.
• Make sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in re.
Take care not to touch the ventilation openings
when watching theTV for long periods as the
ventilation openings may become hot.This
does not aect the operation or performance of
the product.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
Prevent dust collecting on the power plug pins
or outlet.This may cause a re hazard.
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not press strongly upon the panel with a
hand or sharp object such as nail, pencil or pen,
or make a scratch on it, as it may causedamage
to screen.
Avoid touching the screen or holding your
nger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
When cleaning the product and its components,
unplug the power rst and wipe it with a soft
cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with
water or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives or
wax, benzene, alcohol etc., which can damage
the product and its panel. Otherwise, this may
result in re, electric shock or product damage
(deformation, corrosion or breakage).

8
ENGLISH
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn o this unit by SWITCH.
When unplugging the cable, grab the plug and
unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power
cord from the power board, as this could be
hazardous.
When moving the product, make sure you turn
the power o rst.Then, unplug the power
cables, antenna cables and all connecting
cables.
TheTV set or power cord may be damaged,
which may create a re hazard or cause electric
shock.
When moving or unpacking the product,
work in pairs because the product is heavy.
Otherwise, this may result in injury.
Contact the service centre once a year to clean
the internal parts of the product.
Accumulated dust can cause mechanical failure.
Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
If the product feels cold to the touch, there may
be a small“icker”when it is turned on.This is
normal, there is nothing wrong with product.
The panel is a high technology display product
with resolution of two million to six million
pixels.You may see tiny black dots and/or
brightly coloured dots (red, blue or green) at
a size of 1ppm on the panel.This does not
indicate a malfunction and does not aect the
performance and reliability of the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.

ENGLISH
9
You may nd dierent brightness and color
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
* LG LED TVs are LCD TVs with LED
backlighting.
Displaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from a
video game) for a prolonged time may cause
damage to the screen, resulting in retention of
the image, which is known as image sticking.
The warranty does not cover the product for
image sticking.
Avoid displaying a xed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch theTV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
Generated sound
“Cracking”noise: A cracking noise that
occurs when watching or turning o theTV
is generated by plastic thermal contraction
due to tempera-ture and humidity. This
noise is common for products where thermal
deformation is required. Electrical circuit
humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit,
which supplies a large amount of current to
operate a product. It varies depending on the
product.
This generated sound does not aect the
performance and reliability of the product.
Do not use high voltage electrical goods near
theTV(e.g. electric mosquito-swatter).This may
result in product malfunction.

10
ENGLISH
Viewing 3D imaging
(Only 3D models)
WARNING
Viewing environment
• ViewingTime
--When watching 3D contents, take 5 - 15
minute breaks every hour. Viewing 3D
contents for a long period of time may
cause headache, dizziness, fatigue or eye
strain.
Those that have a
photosensitive seizure or
chronic illness
• Some users may experience a seizure or
other abnormal symptoms when they are
exposed to a ashing light or particular
pattern from 3D contents.
• Do not watch 3D videos if you feel nausea,
are pregnant and/ or have a chronic illness
such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
• 3D Contents are not recommended to those
who suer from stereo blindness or stereo
anomaly. Double images or discomfort in
viewing may be experienced.
• If you have strabismus (cross-eyed),
amblyopia (weak eyesight) or astigmatism,
you may have trouble sensing depth and
easily feel fatigue due to double images. It
is advised to take frequent breaks than the
average adult.
• If your eyesight varies between your right
and left eye, correct your eyesight prior to
watching 3D contents.
Symptoms which require
discontinuation or
refraining from watching 3D
contents
• Do not watch 3D contents when you feel
fatigue from lack of sleep, overwork or
drinking.
• When these symptoms are experienced, stop
using/watching 3D contents and get enough
rest until the symptom subsides.
--Consult your doctor when the
symptoms persist. Symptoms may
include headache, eyeball pain,
dizziness, nausea, palpitation, blurriness,
discomfort, double image, visual
inconvenience or fatigue.
CAUTION
Viewing environment
• Viewing Distance
--Maintain a distance of at least twice the
screen diagonal length when watching
3D contents. If you feel discomfort in
viewing 3D contents, move further away
from the TV.
Viewing age
• Infants/Children
--Usage/ Viewing 3D contents for children
under the age of 6 are prohibited.
--Children under the age of 10 may
overreact and become overly excited
because their vision is in development
(for example: trying to touch the
screen or trying to jump into it. Special
monitoring and extra attention is
required for children watching 3D
contents.

ENGLISH
11
--Children have greater binocular disparity
of 3D presentations than adults because
the distance between the eyes is shorter
than that of adults. Therefore they will
perceive more stereoscopic depth
compared to adults for the same 3D
image.
• Teenagers
--Teenagers under the age of 19 may react
with sensitivity due to stimulation from
light in 3D contents. Advise them to
refrain from watching 3D contents for a
long time when they are tired.
• Elderly
--The elderly may perceive less 3D effect
compared to the young. Do not sit
closer to the TV than the recommended
distance.
Cautions when using the 3D
glasses
• Make sure to use LG 3D glasses. Otherwise,
you may not be able to view 3D videos
properly.
• Do not use 3D glasses instead of your normal
glasses, sunglasses or protective goggles.
• Using modied 3D glasses may cause eye
strain or image distortion.
• Do not keep your 3D glasses in extremely
high or low temperatures. It will cause
deformation.
• The 3D glasses are fragile and are easily
scratched. Always use a soft, clean piece of
cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp
objects or clean/wipe them with chemicals.
Preparing
NOTE
• If theTV is turned on for the rst time after
it was shipped from the factory, initialization
of theTV may take a few minutes.
• Image shown may dier from your TV.
• Your TV’s OSD (On Screen Display) may dier
slightly from that shown in this manual.
• The available menus and options may dier
from the input source or product model that
you are using.
• New features may be added to this TV in the
future.
• TheTV can be placed in standby mode in
order to reduce the power consumption. And
theTV should be turned o if it will not be
watched for some time, as this will reduce
energy consumption.
• The energy consumed during use can
be signicantly reduced if the level of
brightness of the picture is reduced, and this
will reduce the overall running cost.
• The items supplied with your product may
vary depending on the model.
• Product specications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
• For an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the
USB cable or USB memory stick does not t
into yourTV’s USB port.

12
ENGLISH
A
B
A
B
*A
<
=
10 mm
*B
<
=
18 mm
• Use a certied cable with the HDMI logo
attached.
• If you do not use a certied HDMIcable,
the screen may not display or a connection
error may occur. (Recommended HDMICable
Types)
- High-Speed HDMI®/TM Cable (3m or less)
- High-Speed HDMI®/TM Cable with Ethernet
(3m or less)
CAUTION
• Do not use any unapproved items to ensure
the safety and product life span.
• Any damage or injuries caused by using
unapproved items are not covered by the
warranty.
• Some models have a thin lm attached on to
the screen and this must not be removed.
Separate purchase
Separate purchase items can be changed or
modied for quality improvement without any
notication. Contact your dealer to buy these
items. These devices only work with certain
models.
The model name or design may be changed
depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
(Depending on model)
AG-F***
Cinema 3D
Glasses
AN-MR600
Magic Remote
AN-VC550
Smart
Camera
AG-F***DP
Dual Play
Glasses
LG Audio
Device
Maintenance
Cleaning your TV
Clean yourTV regularly to keep the best
performance and to extend the product
lifespan.
• Make sure to turn the power o and
disconnect the power cord and all other
cables rst.
• When theTV is left unattended and unused
for a long time, disconnect the power cord
from the wall outlet to prevent possible
damage from lightning or power surges.
Screen, frame, cabinet and
stand
To remove dust or light dirt, wipe the surface
with a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a
soft cloth dampened in clean water or a diluted
mild detergent.Then wipe immediately with a
dry cloth.
• Avoid touching the screen at all times, as
this may result in damage to the screen.
• Do not push, rub, or hit the screen surface
with your ngernail or a sharp object, as
this may result in scratches and image
distortions.

ENGLISH
13
• Do not use any chemicals as this may
damage the product.
• Do not spray liquid onto the surface. If water
enters theTV, it may result in re, electric
shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the
power cord regularly.
Lifting and moving
the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
• It is recommended to move the TV in the box
or packing material that theTV originally
came in.
• Before moving or lifting theTV, disconnect
the power cord and all cables.
• When holding theTV, the screen should face
away from you to avoid damage.
• Hold the top and bottom of the TV frame
rmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
• When transporting a largeTV, there should
be at least 2 people.
• When transporting the TV by hand, hold the
TV as shown in the following illustration.
• When transporting the TV, do not expose the
TV to jolts or excessive vibration.
• When transporting the TV, keep theTV
upright, never turn theTV on its side or tilt
towards the left or right.
• Do not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
• When handling theTV, be careful not to
damage the protruding joystick button.
CAUTION
• Avoid touching the screen at all times, as
this may result in damage to the screen.
• Do not move theTV by holding the cable
holders, as the cable holders may break, and
injuries and damage to theTV may occur.
Using the joystick
button
You can simply operate theTV functions,
pressing or moving the joystick button up,
down, left or right.

14
ENGLISH
Joystick Button
Basic functions
Power On
When theTV is turned
o, place your nger
on the joystick button
and press it once and
release it.
Power O
When theTV is turned
on, place your nger
on the joystick button
and press it once for
a few seconds and
release it. All running
apps will close, and
any recording in
progress will stop.
Volume
Control
If you place your
nger over the joystick
button and move it left
or right, you can adjust
the volume level you
want.
Programmes
Control
If you place your
nger over the joystick
button and move it
up or down, you can
scrolls through the
saved programmes you
want.
Adjusting the menu
When theTV is turned on, press the joystick
button one time. You can adjust the Menu
items moving the joystick button up, down, left
or right.
Turns the power o.
Clears on-screen displays and returns
toTV viewing.
Changes the input source.
Accesses the quick settings.
NOTE
• When your nger over the joystick button
and push it to the up, down, left or right, be
careful not to press the joystick button. If
you press the joystick button rst, you may
not be able to adjust the volume level and
saved programmes.
Mounting on a
table
(Depending on model)
1Lift and tilt theTV into its upright position on
a table.
• Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2Connect the power cord to a wall outlet.

ENGLISH
15
CAUTION
• Do not place theTV near or on sources
of heat, as this may result in re or other
damage.
Using the kensington
security system
(This is not available for all models.)
• Image shown may dier from your TV.
The Kensington security system connector
is located at the rear of theTV. For more
information of installation and using, refer
to the manual provided with the Kensington
security system or visit http://www.kensington.
com. Connect the Kensington security system
cable between theTV and a table.
Securing the TV to a
wall
(This feature is not available for all models.)
1Insert and tighten the eye-bolts, orTV
brackets and bolts on the back of theTV.
• If there are bolts inserted at the eye-bolts
position, remove the bolts rst.
2Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of theTV.
3Connect the eye-bolts and wall brackets
tightly with a sturdy rope. Make sure to keep
the rope horizontal with the at surface.
CAUTION
• Make sure that children do not climb on or
hang on theTV.
NOTE
• Use a platform or cabinet that is strong and
large enough to support theTV securely.
• Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the
rear of theTV carefully and install the wall
mount bracket on a solid wall perpendicular
to the oor.When you attach theTV to other
building materials, please contact qualied
personnel. LG recommends that wall mounting
be performed by a qualied professional
installer. We recommend the use of LG’s wall
mount bracket.When you do not use LG’s wall
mount bracket, please use a wall mount bracket
where the device is adequately secured to the
wall with enough space to allow connectivity to
external devices.

16
ENGLISH
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet theVESA standard. Standard
dimensions for the wall mount kits are
described in the following table.
Separate purchase(Wall
mounting bracket)
Model 32/40/43LF63**
32LF65** 49/55LF63**
VESA (A x B) 200 x 200 300 x 300
Standard
screw M6 M6
Number of
screws 4 4
Wall mount
bracket LSW240B
MSW240
LSW350B
MSW240
Model 42/50/55LF65**
VESA (A x B) 400 x 400
Standard
screw M6
Number of
screws 4
Wall mount
bracket LSW440B
MSW240
A
B
CAUTION
• Disconnect the power rst, and then move
or install theTV. Otherwise electric shock
may occur.
• Remove the stand before installing theTV
on a wall mount by performing the stand
attachment in reverse.
• If you install theTV on a ceiling or slanted
wall, it may fall and result in severe
injury. Use an authorised LG wall mount
and contact the local dealer or qualied
personnel.
• Do not over tighten the screws as this may
cause damage to theTV and void your
warranty.
• Use the screws and wall mounts that meet
theVESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
NOTE
• Use the screws that are listed on theVESA
standard screw specications.
• The wall mount kit includes an installation
manual and necessary parts.
• The wall mount bracket is not provided.You
can obtain additional accessories from your
local dealer.
• The length of screws may dier depending
on the wall mount. Make sure to use the
proper length.
• For more information, refer to the manual
supplied with the wall mount.
• When installing the wall mounting bracket,
use the Adhesive Label.The Adhesive Label
will protect the opening from accumulating
dust and dirt. (Only when the item of the
following form is provided)

ENGLISH
17
Provided Item
Adhesive Label
• When attaching a wall mounting bracket
to theTV, insert the wall mount spacers
into theTV wall mount holes to adjust the
vertical angle of the TV. (Only when the
item of the following form is provided)
Provided Item
Wall Mount Spacer
Connections
(notications)
Connect various external devices to theTV and
switch input modes to select an external device.
For more information of external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers,
DVD players,VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
NOTE
• The external device connection may dier
from the model.
• Connect external devices to theTV
regardless of the order of theTV port.
• If you record a TV program on a DVD recorder
orVCR, make sure to connect theTV signal
input cable to theTV through a DVD recorder
orVCR. For more information of recording,
refer to the manual provided with the
connected device.
• Refer to the external equipment’s manual
for operating instructions.
• If you connect a gaming device to theTV, use
the cable supplied with the gaming device.
• In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust
the brightness and contrast on the PICTURE
menu until the picture is clear.
• In PC mode, some resolution settings
may not work properly depending on the
graphics card.
Antenna connection
Connect theTV to a wall antenna socket with an
RF cable (75 Ω).
• Use a signal splitter to use more than 2TVs.
• If the image quality is poor, install a signal
amplier properly to improve the image
quality.
• If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
• An antenna cable and converter are not
supplied.
• Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC

18
ENGLISH
Satellite dish
connection
(Only satellite models)
Connect theTV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digitalTV
mode.
NOTE
• Check if the CI module is inserted into the
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to theTV and the PCMCIA
card slot.
• If theTV does not display any video and
audio when CI+ CAM is connected, please
contact to theTerrestrial/Cable/Satellite
Service Operator.
Euro scart connection
(Depending on model)
Transmits the video and audio signals from
an external device to theTV set. Connect the
external device and theTV set with the euro
scart cable as shown.
Output
Type
Current
input mode
AV1
(TV Out1)
DigitalTV DigitalTV
AnalogueTV, AV
AnalogueTV
Component
HDMI
1 TV Out : Outputs AnalogueTV or DigitalTV
signals.
• Any Euro scart cable used must be signal
shielded.
• When watching digitalTV in 3D imaging
mode, only 2D out signals can be output
through the SCART cable. (Only 3D models)
• If you use theTime Machine function on
digitalTV, monitor out signals cannot be
output through the SCART cable. (Only 3D
models)
Other connections
Connect yourTV to external devices. For the
best picture and audio quality, connect the
external device and theTV with the HDMI cable.
Some separate cable is not provided.
Remote control
(Depending on model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use theTV correctly.
To replace batteries, open the battery cover,
replace batteries (1.5V AAA) matching
the and ends to the label inside the
compartment, and close the battery cover. To
remove the batteries, perform the installation
actions in reverse.
CAUTION
• Do not mix old and new batteries, as this
may damage the remote control.
• The remote control will not be included for
all sales market.

ENGLISH
19
Make sure to point the remote control toward
the remote control sensor on the TV.
P
A
G
E
FAV
MUTE
INPUT
EXIT
OK
LIVE MENU
MY APPS
LIVE TV
REC/
TEXT T.OPT
APP/
AD
BACK
TV/RAD
Q.MENU
RECENT
SUBTITLE
1 .,;@ 2 abc 3 def
4 ghi 5 jkl 6 mno
7 pqrs 8 tuv
0
9
wxyz
GUIDE
Q.VIEW
INFO
2 3
4
1
5
A
B
A
(POWER) Turns theTV on or o.
1Changes the input source.
(Depending on model)
1Changes the input source.
(Depending on model)
2/ (Q.Settings) Accesses the
quick settings. (Depending on model)
2Accesses the quick settings.
(Depending on model)
3Resizes an image. (Depending on
model)
3Views the information of the
current programme and screen. (Depending
on model)
(User Guide) Sees user-guide.
B
Number buttons Enters numbers.
Shows programme guide.
(Space) Opens an empty space on the
screen keyboard.
Returns to the previously viewed
programme.
Adjusts the volume level.
Accesses your favourite programme list.
4Views the information of the
current programme and screen. (Depending
on model)
4Used for viewing 3D video.
(Depending on model)
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next
screen.
P
A
G
E
FAV
MUTE
INPUT
EXIT
OK
LIVE MENU
MY APPS
LIVE TV
REC/
TEXT T.OPT
APP/
AD
BACK
TV/RAD
Q.MENU
RECENT
SUBTITLE
1 .,;@ 2 abc 3 def
4 ghi 5 jkl 6 mno
7 pqrs 8 tuv
0
9
wxyz
GUIDE
Q.VIEW
INFO
2 3
4
1
5
6
D
C
C
Shows the previous history.
5(HOME) Accesses the Home menu.
(Depending on model)
5Accesses the Home menu.
(Depending on model)
Shows the list of Apps.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
Selects menus or options and conrms
your input.
Returns to the previous level.
Shows the list of Recommended,
Programmes, Search and Recorded.
(Depending on model)
Clears on-screen displays and returns to
TV viewing.

20
ENGLISH
D
6Coloured buttons These access special
functions in some menus.
( : Red, : Green, :Yellow, : Blue)
TELETEXT buttons( , ) These
buttons are used for teletext.
Returns to LIVETV.
Selects the MHPTV menu source.
(Only Italy) (Depending on model)
Control buttons ( ) Controls
the Premium contents,Time MachineReady
or SmartShare menus or the SIMPLINK
compatible devices (USB or SIMPLINK orTime
MachineReady).
Starts to record and displays record
menu. (Only Time MachineReady supported
model) (Depending on model)
Recalls your preferred subtitle in
digital mode.
By Pressing AD button, audio descriptions
function will be enabled.
Selects Radio,TV and DTV
programme.
Magic remote
functions
(Depending on model)
When the message“Magic remote battery is
low. Change the battery.”is displayed, replace
the battery.
To replace batteries, open the battery
cover, replace batteries (1.5 V AA) matching
the and ends to the label inside the
compartment, and close the battery cover. Be
sure to point the magic remote toward the
remote control sensor on the TV. To remove the
batteries, perform the installation actions in
reverse.
CAUTION
• Do not mix old and new batteries, as this
may damage the remote control.
6 mno
9 wxyz
3 def
2 abc
1 . @
4 ghi
8 tuv
7 pqrs
0
5 jkl
GUIDE
LIST INFO
EXIT
TEXT T.OPT
SUBT.
A
B
A
(POWER) Turns theTV on or o.
(INPUT) Changes the input source.
* Pressing and holding the button displays
all the lists of external inputs.
Number buttons Enters numbers.
Accesses the saved programme list.
(Space) Opens an empty space on the
screen keyboard.
Views the information of the current
programme and screen.
B
Adjusts the volume level.
P Scrolls through the saved
programmes.
(MUTE) Mutes all sounds.
* By pressing and holding the button,
audio descriptions function will be enabled.
(Depending on model)
(HOME) Accesses the Home menu.