LG BEJLB504N User manual

APPENDIX G :
FCC ID : BEJLB504N
USER’S MANUAL

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Important Precautions

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.

A3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Positioning your display
1.Remove the tape.
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
Height Range : maximun 3.39inch (86.1mm)
Landscape & Portrait : You can rotate the panel 90o clockwise.
(* For detailed information, please refer to the Pivot Sofeware CD provided.)
2. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -24˚~145˚
145˚ -24˚
* Make sure not to
touch the floor
when the head
rotates to use the
Pivot function.
<Image 1>
Put the set as the
picture below
<Image 1> to
remove the tape.
Do not remove the tape
with the set up side
down as the <Image 2>
The base part may
spring up to injure your
hand.
<Image 2>

A4
Connecting the Display
Using the Computer
1.Connect the signal cable. When attached, tighten the thumbscrews to secure
the connection.
2.Connect the power cord into a proper power outlet that is easily accessible and
close to the display.
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
Wall-outlet type*
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display
may differ from the view as shown.
PC-outlet type*
PC
MAC
Power Cord Signal Cable
Digital signal
- DVI*Analog signal
D-sub*
* Varies according to model.

A5
Control Panel Functions
Front Panel Controls
Buttons
Use these buttons to choose or adjust items in
the On Screen Display.
MENU Button
Use this button to enter or exit the On Screen
Display.
Use this button to turn the display on or off.
This Indicator lights up green when the display
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
Power Button
Power (DPMS)
Indicator
Use this button to enter a selection in the On Screen
Display.
SELECT/SOURCE
Button
Control Function

A6
Control Panel Functions
Control Direct Access Function
Bring up Contrast and Brightness adjustment.
100
100
PROCESSING
AUTO CONFIGURATION
When adjusting your display settings, always press the
/AUTO button before entering the On Screen
Display(OSD). This will automatically adjust your display image
to the ideal settings for the current screen resolution size
(display mode).
The best display mode is 1024x768.
AUTO adjustment function
CONTROLS LOCKED
CONTROLS UNLOCKED
This function allows you to secure the current control settings,
so that they cannot be inadvertently changed. Press and hold
the MENU button and button for 3 seconds: the message
“CONTROLS LOCKED” appears.
You can unlock the OSD controls at any time by pushing the
MENU button and button for 3 seconds:
the message “CONTROLS UNLOCKED” will appear.
CONTROLS LOCKED/UNLOCKED
:
MENU and
Use this button to make Dsub or DVI connector active. This
feature is used when two computers are connected to the
display. The default setting is Dsub.
SOURCE

A7
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the or Buttons. When the icon you want
becomes highlighted, press the SELECT/SOURCE Button.
Use the Buttons to adjust the item to the desired level.
Accept the changes by pressing the SELECT/SOURCE Button.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
SELECT/SOURCE
SELECT/SOURCE
MENU
MENU

A8
NOTE
The order of icons may differ depending on the model (A8~A10).
* This function is available for designated models only.
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
To adjust the brightness and
contrast of the screen
BRIGHTNESS
CONTRAST
COLOR
POSITION
TRACKING
SETUP
Main menu Sub menu A D Reference
PRESET 9300K
6500K
R/G/B(User Color)
To adjust the position of the
screen
To customize the color of the
screen
To customize the screen status
for a user's operating environment
To improve the clarity and
stability of the screen
: Adjustable
A : Analog Input
D : Digital Input
BRIGHTNESS
CONTRAST
V POSITION
H POSITION
CLOCK
PHASE
LANGUAGE *
IMAGE SIZE *
OSD POSITION *
SIGNAL *

A9
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
OSD Adjust Description
BRIGHTNESS
To adjust the brightness of the screen.
CONTRAST
To adjust the contrast of the screen.
Vertical Position
To move image up and down.
Horizontal Position
To move image left and right.
To adjust the brightness and contrast of the screen
To adjust the position of the screen
OSD Adjust Description
BRIGHTNESS / CONTRAST
88
100
PRESET
RED
GREEN
BLUE
9300K/6500K
Select the screen color.
• 9300K: Slightly bluish white.
• 6500K: Slightly reddish white.
Set your own color levels.
To customize the color of the screen
OSD Adjust Description
COLOR
PRESET 9300K 6500K
RED
GREEN
BLUE
POSITION
61
39

A10
On Screen Display(OSD) Selection and Adjustment
To improve the clarity and stability of the screen
OSD Adjust Description
TRACKING
CLOCK
PHASE
To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
CLOCK
PHASE
To customize the screen status for a user's operating environment
OSD Adjust Description
NOTE
* This function is available for designated models only.
LANGUAGE ENGLISH
FULL
IMAGE SIZE
SETUP
OSD POSITION
SIGNAL DSUB ANALOG
ELAPSED TIME H
0
1024x768/60Hz
PRESET MODE
DSUB ANALOG INPUT
To choose the language in which the
control names are displayed.
This function displays the image in its
original size or enlarged size so as to
fit in the full screen of the LCD panel.
To adjust position of the OSD window
on the screen.
To select DSUB ANALOG, DVI
DIGITAL or DVI ANALOG / as the
active input. This feature is used
when two computers are connected
to the display. The display
automatically detects the proper input
when only one video source is
connected.
ELAPSED TIME
To display the use time of display.
LANGUAGE*
IMAGE SIZE*
OSD POSITION*
SIGNAL*

A11
Troubleshooting
Check the following before calling for service.
No image appears
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator green?
Is the power indicator
amber?
Do you see an "INPUT
SIGNAL OUT OF
RANGE" message on
the screen?
Do you see a "NO
SIGNAL" message on
the screen?
Check and see if the power cord is
connected properly to the power outlet.
Press the Power button.
Adjust the brightness and the contrast.
If the display is in power saving mode, try
moving the mouse or pressing any key on
the keyboard to bring up the screen.
This message appears when the signal
from the PC (video card) is out of horizontal
or vertical frequency range of the display.
See the 'Specifications' section of this
manual and configure your display again.
This message appears when the signal
cable between your PC and your display is
not connected. Check the signal cable and
try again.
Have you installed the
display driver? Be sure to install the display driver from the
display driver CD (or diskette) that comes
with your display. Or, you can also
download the driver from our web site:
http://www.lge.com.
Have you installed the display driver?

A12
Troubleshooting
Display Position is
incorrect.
On the screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Press the /AUTO button to
automatically adjust your display image to
the ideal setting.
If the results are unsatisfactory, adjust the
image position using the H position and V
position icon in the on screen display.
Press the /AUTO button to
automatically adjust your display image to
the ideal setting.
If the results are unsatisfactory, decrease
the vertical bars or stripes using the
CLOCK icon in the on screen display.
Press the /AUTO button to
automatically adjust your display image to
the ideal setting.
If the results are unsatisfactory, decrease
the horizontal bars using the PHASE icon in
the on screen display.
Display image is incorrect

A13
Specifications
NOTE
Information in this document is subject to change without notice.
15 inches (38.1cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
15 inches viewable
0.3 mm pixel pitch
Horizontal Freq. 31 - 63kHz (Automatic)
Vertical Freq. 56 - 75Hz (Automatic)
Input Form Separate TTL, Positive/Negative
Composite TTL, Positive/Negative
SOG (Sync On Green)
Digital
Signal Input 15 pin D-Sub Connector
DVI - I connector (Digital/Analog)
Input Form RGB Analog (0.7Vp-p/75ohm), Digital
Max Digital : VESA 1024 x 768@60Hz
Analog : VESA 1024 x 768@75Hz
Recommend VESA 1024 x 768@60Hz
DDC 2B
Normal :
30W
Stand-by/Suspend ≤3W
Power Off ≤3W
Full Up Position Folded Position
Width 35.60 cm / 14.02 inches 35.60 cm / 14.02 inches
Height 38.00 cm / 14.96 inches 10.33 cm / 4.07 inches
Depth 22.90 cm / 9.02 inches 29.14 cm / 11.47 inches
Net 5.1 kg (11.46 lbs)
Tilt Range -24˚~145˚ (Head)
Height Range 3.89inch (86.1mm)
Rotate 90˚ clockwise (Landscape->Portrait)
AC 100-240V 50/60Hz 0.6A
Operating Conditions
Temperature 10˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity 5 % to 95 % non-Condensing
Attached( O ), Detached ( )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
TCO99
Display
Sync Input
Video Input
Resolution
Plug&Play
Power
Consumption
Dimensions
&Weight
(with tilt stand)
Tilt Range
Power Input
Environmental
Conditions
Tilt Stand
Signal cable
Power cord
Regulations

A14
Specifications
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
*12
13
14
*Recommended
Unlike CRT monitors, which require a high refresh rate to minimize flickering, TFT
technology is inherently flicker-free. If possible, configure your computer for 1024 x 768
addressability at 60Hz vertical refresh rate.
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
31.468
31.468
31.469
35.000
37.861
37.500
35.156
37.879
48.077
46.875
49.725
48.363
56.476
60.023
70
70
60
66.67
72.8
75
56.25
60
72
75
75
60
70
75
VGA
VGA
VGA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
VESA wall mounting
Connected to another object (stand
type and wall-mounted type. This
monitor accepts a VESA-compliant
mounting interface pad.)
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most computer
stores

Specifications
A15
Signal Connector Pin Assignment
18
9
17 24
16
C1
C4
C3
C2
C5
Pin Signal(DVI-I)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
T. M. D. S. Data2-
T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4-
T. M. D. S. Data4+
DDC Clock
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1-
T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3-
T. M. D. S. Data3+
+5V Power
Ground
(return for +5V,
H. Sync. and V. Sync.)
Pin Signal(DVI-I)
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Hot Plug Detect
T. M. D. S. Data0-
T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5-
T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
Analog Red
Analog Green
Analog Blue
Analog H. Sync.
Analog Ground
T. M. D. S. (Transition Minimized Differential Signaling)
DVI-I Connector

A16
Making use of USB (Universal Serial Bus)
- Optional
USB (Universal Serial Bus) is an innovation in connecting your different
desktop peripherals conveniently to your computer. By using the USB, you will
be able to connect your mouse, keyboard, and other peripherals to your display
instead of having to connect them to your computer. This will give you greater
flexibility in setting up your system. USB allows you to connect a chain of up to
120 devices on a single USB port; and you can “hot” plug (attach them while
the computer is running) or unplug them while maintaining the Plug and the
Plug auto detection and configuration. This display has an integrated BUS-
powered USB hub, allowing up to 2 other USB devices to be attached it.
USB connection
1. Connect the upstream port of the display to the downstream port of the USB
compliant PC or another hub using the USB cable. (Computer must have a
USB port)
2. Connect the USB compliant peripherals to the downstream ports of the
display.
NOTE
To activate the USB hub function, the display must be connected to a USB compliant PC(OS)
or another hub with the USB cable(enclosed).
When connecting the USB cable, check that the shape of the connector at the cable side
matches the shape at the connecting side.
Even if the display is in a power saving mode, USB compliant devices will function when they
are connected the USB ports(both the upstream and downstream) of the display.
USB downstream Port
connect the cables from USB
compliant peripherals-such as
keyboard, mouse, etc
This is a simplified representation
of rear view.
To USB downstream port of
the USB compliant PC or
another hub cable
USB upstream Port

A17
Making use of USB (Universal Serial Bus)
- Optional
IMPORTANT: These USB connectors are not designed for use with high-power USB devices
such as a video camera, scanner, etc. LGE recommends connecting high-power USB devices
directly to the computer
Rev. 1.1 complied BUS-powered hub
100mA for each (MAX)
12 Mbps (full), 1.5 Mbps (low)
1 Upstream port
2 Downstream ports
USB standard
Downstream power supply
Communication speed
USB port
USB Specifications

Reference Guide
for Precaution,
Service, Warranty
and Diskette Install
English
Deutsch
Français
Italiano
Español
Nederlands
Português

i
Monitor Registration
The model and serial numbers are found
on the rear of this unit. These numbers
are unique to this unit and not available to
others. You should record requested
information here and retain this guide as
a permanent record of your purchase.
Staple your receipt here.
Date of Purchase :
Dealer Purchased From
:
Dealer Address :
Dealer Phone No. :
Model No. :
Serial No. :
English
Important Precautions ..................................................1
DDC (Display Data Channel) .......................................1
Energy Saving Design .................................................2
Service ..........................................................................2
Deutsch
Wichtige Hinweise ........................................................2
DDC (Display Data Channel) ......................................3
Energieversorgung .......................................................3
Wartung ........................................................................3
Français
Consignes de Sécurité ..................................................4
DDC (Display Data Channel) .......................................4
Caractéristique D’économie D’énergie ........................5
Maintenance du Moniteur .............................................5
Italiano
Precauzioni Importanti ..................................................5
DDC (Display Data Channel) Canale Dati del Monitor 6
Modello Conforme alla Normativa sul Risparmio
Energetico ......................................................................6
Manutenzione ................................................................6
Español
Precauciones Importantes ............................................7
DDC (Canal de despliegue de información) ................7
Diseño de Ahorro de Energía .......................................8
Servicio ..........................................................................8
Nederlands
Belangrijke voorzorgsmaatregelen ..............................8
DDC (Display Data Channel) .......................................9
Energiebesparingssysteem ..........................................9
Onderhoud .....................................................................9
Português
Precauções Importantes .............................................10
DDC (Display Data Channel) .....................................10
Sistema de Gerenciamento de Energia ....................11
Manutenção .................................................................11
Regulatory Information
FCC Compliance Statement .....................................11
Canadian DOC Notice ................................................11
CE Conformity Notice (for Europe) .............................12
Low Radiation Compliance (MPR II)...........................12
TCO95 ..........................................................................12
TCO99 ..........................................................................13
EPA (U.S.A only)..........................................................14
NOM MARK (Mexico only)..........................................14
Warranty
the United States and Canada - CDT Monitor ...........15
the United States and Canada - LCD Monitor............16
Australia - CDT & LCD Monitor...................................17
Brazil - CDT & LCD Monitor ........................................18
Mexico - CDT Monitor..................................................19
the United Kingdom - CDT&LCD Monitor ..................21
Monitor Driver Installation
Monitor Driver Installation ..........................................22
USB Install Guide ........................................................22