LG Flatron L1515S User manual

COLOR MONITOR
SERVICE MANUAL
Website:http://biz.LGservice.com
E-mail:http://www.LGEservice.com/techsup.html
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS NO. : CL-61
MODEL: L1515S (L1515SM-AL**R, AG**R)
L1515S(S) (L1515SM-AG**S)
L1515S(K) (L1515SM-AG**B)
( ) **Same model for Service
*Same looking with new chassis

CONTENTS
SPECIFICATIONS
- 2 -
1. LCD CHARACTERISTICS
Type : TFT XGA LCD Module
Size : 352.0(H) x 263.5(V) x 14.0(T)
Pixel Pitch : 0.297mm x 0.297mm
Color Depth :
6bits(with FRC)/ 16M colors
Active Video Area : 15.0inch
(304.128 x 228.096)
Surface Treatment : Anti-Glare, Hard Coating (3H)
Backlight Unit : Top/Bottom edge side 2CCFL
Electrical Interface : LVDS interface
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥
10
(LPL Module)
Left : 55° min. 65° typ. Right: 55° min. 65° typ.
Top : 45° min. 45° typ. Bottom: 50° min. 55° typ.
(CMO Module)
Left : 50° min. 60° typ. Right: 50° min. 60° typ.
Top : 30° min. 40° typ. Bottom: 50° min. 60° typ.
2-2. Luminance
:
200(min.), 250(typ.) at Center point
2-3. Contrast Ratio :300(min.), 400(typ.)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
1) Type : Separate Sync. (Horizontal & Vertical)
2) Input Voltage Level: Low=0~0.8V, High=2.1~5.5V
3) Sync Polarity : Positive or Negative
3-2. Video Input Signal
1) Type : R, G, B Analog
2) Voltage Level : 0~0.7 V
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.35 Vp-p
c) Color 15, 0 : 0.7 Vp-p
3) Input Impedance : 75 Ω
3-3. Operating Frequency
Horizontal : 30 ~ 63kHz
Vertical : 56 ~ 75Hz
4. POWER SUPPLY
4-1. Power
100-240V~, 50/60Hz 0.6A
4-2. Power Consumption
5. ENVIRONMENT
5-1. Operating Temperature: 10°C~35°C (50°F~95°F)
5-2. Operating Humidity : 10%~80%
5-3. MTBF : 50,000 Hours (Min.)
Lamp Life : 40,000 Hours (Min.)
6. DIMENSIONS (with TILT/SWIVEL)
(FULL Up Position)
Width : 350mm (13.78'')
Depth : 133mm (5.24'')
Height : 318mm (12.52'')
(Folded Position)
Width : 350mm (13.78'')
Depth : 64mm (2.52'')
Height : 334mm (13.15'')
7. WEIGHT (with TILT/SWIVEL)
Net. Weight : 2.5kg (5.51 lbs)
Gross Weight : 5.5kg (12.13 lbs)
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 3
TIMING CHART ....................................................... 4
OPERATING INSTRUCTIONS ................................ 5
WIRING DIAGRAM ................................................. 6
BLOCK DIAGRAM ................................................... 7
DESCRIPTION OF BLOCK DIAGRAM ................... 8
ADJUSTMENT ...................................................... 10
TROUBLESHOOTING GUIDE .............................. 12
EXPLODED VIEW...................................................17
REPLACEMENT PARTS LIST ...............................18
SCHEMATIC DIAGRAM......................................... 20
MODE
POWER ON (NORMAL)
STAND-BY
SUSPEND
DPM OFF
POWER S/W OFF
H/V SYNC
ON/ON
OFF/ON
ON/OFF
OFF
-
POWER CONSUMPTION
less than 25 W
less than 1 W
less than 1 W
less than 1 W
less than 1 W
LED COLOR
GREEN
AMBER
AMBER
AMBER
OFF
VIDEO
ACTIVE
OFF
OFF
OFF
-

- 3 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
• There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
• Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
• Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
• Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
• If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
• Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
PRECAUTION
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

TIMING CHART
- 4 -
VIDEO
SYNC
B
D
CFE
A
H / V
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
H (Pixels)
V (Lines)
Sync
Polarity
+
–
–
+
–
–
–
–
–
–
–
–
+
+
+
+
+
+
+
+
–
–
–
–
–
–
+
+
Dot
Clock
25.175
28.322
25.175
30.24
31.5
31.5
36.0
40.0
50.0
49.5
57.2832
65
75
78.75
Frequency
31.468 KHz
70.0 Hz
31.468 KHz
70.0 Hz
31.469 KHz
60.0 Hz
35.00 KHz
66.67 Hz
37.861 KHz
72.8 Hz
37.50 KHz
75.0 Hz
35.156KHz
56.25 Hz
37.879 KHz
60.3 Hz
48.077 KHz
72.188 Hz
46.875 KHz
75.0 Hz
49.725 KHz
74.55 Hz
48.363 KHz
60.0 Hz
56.476 KHz
70.0 Hz
60.023 KHz
75.0 Hz
Resolution
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
Total
Period
( E )
800
449
900
449
800
525
864
525
832
520
840
500
1024
625
1056
628
1040
666
1056
625
1152
667
1344
806
1328
806
1312
800
Video
Active
Time ( A )
640
350
720
400
640
480
640
480
640
480
640
480
800
600
800
600
800
600
800
600
832
624
1024
768
1024
768
1024
768
Blanking
Time
( B )
160
99
180
49
160
45
224
45
192
40
200
20
224
25
256
28
240
66
256
25
320
43
320
38
304
38
288
32
Sync
Duration
( D )
96
2
108
2
96
2
64
3
40
3
64
3
72
2
128
4
120
6
80
3
64
3
136
6
136
6
96
3
Back
Porch
( F )
48
60
55
34
48
33
96
39
128
28
120
16
128
22
88
23
64
23
160
21
224
39
160
29
144
29
176
28
Front
Porch
( C )
16
37
17
13
16
10
64
3
24
9
16
1
24
1
40
1
56
37
16
1
32
1
24
3
24
3
16
1
MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
(MAC)
(TEXT)

- 5 -
1. Power ON/OFF Button
Use this button to turn the monitor on or off.
Power Indicator
This indicator lights up green when the monitor
operates normally. If the display is in DPM(Energy
Saving)mode, this indicator color change to amber.
2. MENU Button
Use this button to enter or exit the On Screen Display.
3. Button
Use these buttons to choose or adjust items in the On
Screen Display.
4. SELECT / AUTO Button
Use this button to enter a selection in the On Screen Display.
FRONT VIEW REAR VIEW
OPERATING INSTRUCTIONS
D-Sub Signal
Connect
Front Control Panel
132 4
100
100
When adjusting your display settings,
always press the AUTO/SELECT button
before entering the On Screen
Display(OSD). This will automatically
adjust your display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is 1024x768@60Hz.
This feature lets you easily select the best desired image
condition optimized to the environment (ambient
illumination, image types etc.).
•DAY : Bright ambient illumination
•NIGHT : Dark ambient illumination
•TEXT : For text images (Word processing etc.)
•MOVIE : For animation images in videos or movies
•PHOTO : For pictures or drawings
•USER MODE : For use under user setup image
conditions (Brightness, contrast and color tint are
selected by the user in OSD Screen Setup Menu.)
See Front Control Panel
Power Connect
Bring up Contrast and Brightness adjustment.

- 6 -
J706
J704
CN1
CN2 J707
J8
J1
WIRING DIAGRAM
Connector Ass’y P/N:
6631T20024B
Connector Ass’y P/N:
6631T11012R-LPL Module
6631T11021V-CMO Module
This function allows you to secure the current control settings, so that they cannot be inadvertently
changed. Press and hold the MENU button and button for 3 seconds: the message “CONTROLS
LOCKED”appears.
You can unlock the OSD controls at any time by pushing the MENU button and button for 3 seconds:
the message “CONTROLS UNLOCKED”will appear.
CONTROLS LOCKED/UNLOCKED
:
MENU and

- 7 -
BLOCK DIAGRAM
D-SUB
MST9111B
including
(ADC/LVDS/SCALER )
MTV312
Micom
LCD Module
R,G,B
differential
LL
LLVV
VVDD
DDSS
SS
((
((LL
LLoo
ooww
ww VV
VVoo
oollllttttaa
aagg
ggee
ee
DD
DDiiiiffffffffee
eerr
rree
eenn
nnttttiiiiaa
aallll SS
SSiiiigg
ggnn
nnaa
aalllliiiinn
nngg
gg))
))
LIPS
5V
5V
AC Input
3.3V
Reg. Diode
KDS184
5V 3.3V
12V
R,G,B, H/V Sync
3.3V 2.5V
3.3V 2.5V

DESCRIPTION OF BLOCK DIAGRAM
- 8 -
1. Video Controller Part.
This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the
digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 135MHz.
This part consists of the Scaler, ADC, LVDS transmitter.
The Scaler gets the video signal converted analog to digital, interpolates input to 1280 X 1024 resolution signal and
outputs 8-bit R, G, B signal to transmitter.
2. Power Part.
This part consists of the one 3.3V regulator, and two 2.5V drop diodes to convert power which is provided 12V, 5V in
Power board.
5V is provided for LCD panel and Micom.
Also, 5V is converted 3.3V by regulator and 3.3V is converted 2.5V by drop diode.
Converted power is provided for IC in the main board.
3. MICOM Part.
This part consists of EEPROM IC which stores control data, Reset IC and the Micom.
The Micom distinguishes polarity and frequency of the H/V sync are supplied from signal cable.
The controlled data of each modes is stored in EEPROM.

- 9 -
EMI
COMPONENTS
LINE
100 ~ 240V
INPUT RECTIFIER
AND FILTER ENERGY TRANSFER OUTPUT RECTIFIER AND FILTER
12V
5V
GND
SIGNAL
COLLECTI
ON
PHOTO-
COUPLER
ISOLATION
PWM
CONTROL
CIRCUIT
HVDC 100KHz
PRIMARY SECONDARY
50 ~ 60Hz
Operation description_LIPS
LIPS Board Block Diagram
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and also
the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor.

- 10 -
ADJUSTMENT
Windows EDID V1.0 User Manual
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Don’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available to LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys”file to
“c:\WINNT\system32\drivers”folder
b) Run Userport.exe
c) Remove all default number
d) Add 300-3FF
e) Click Start button.
f) Click Exit button.
2. EDID Read & Write
1) Run WinEDID.exe
2) Edit Week of Manufacture, Year of Manufacture,
Serial Number
a) Input User Info Data
b) Click “Update”button
c) Click “Write”button

- 11 -
Figure 1. Cable Connection
220
IBM
Compatible PC
Video Signal
Generator
PARALLEL PORT
Power inlet (required)
Power LED
ST Switch
Power Select Switch
(110V/220V)
Control Line
Not used
RS232C
PARALLEL
V-SYNC POWER
ST
VGS MONITOR
E
E
V-Sync On/Off Switch
(Switch must be ON.)
F
F
A
A
B
B
C
C
1510
5
569
1
1
1
14
13
25
6
5V
5V
5V
4.7K
4.7K
4.7K
74LS06
74LS06
OFF ON
OFF
ON
11
SERVICE OSD
1) Turn off the power switch at the front side of the display.
2) Wait for about 3 seconds and press MENU, POWER switch with 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
a) MODULE : To select applied module.
b) NVRAM INIT : EEPROM initialize(24C08)
c) ADC OFFSET : The lowest value of input leves sets to digitally 0(zero).
d) ADC GAIN : The highest value of input levels sets to digitally 255.
e) ADC CAL : W/B balance sets the gain and offset value.
f) ELAPSED CLEAR : To initialize using time.

- 12 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK POWER
BOARD, AND FIND
OUT A SHORT POINT
AS OPENING
EACH POWER LINE
CHECK J705
VOLTAGE
PIN5, PIN6 (5V)?
NO
CHECK 5VS LINE
(OPEN CHECK)
CHECK
U501 PIN 8 Voltage
(5V) ?
NO
NO
NO
CHECK U201 PIN 122
PULSE
CHECK U201
CHECK 3.3V LINE
CHECK X-TAL
IS U201
PIN114 (3.3V)
VOLTAGE ?
YES
YES NO PROBLEM
YES
CHECK KEY CONTROL
CONNECTOR ROUTINE
YES

- 13 -
2. NO RASTER (OSD IS NOT DISPLAYED) –LIPS
CHECK MICOM INV
ON/OFF PORT.
J705 PIN9
5V? NO
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK LIPS
J705
PIN5, PIN6
5V?
NO
1. CONFIRM BRIGHTNESS
OSD CONTRL STATE.
2. CHECK MICOM DIM-ADJ
PORT
J705 PIN10
5V? NO
LIPS
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL.
(CONTACT PROBE TO
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
NO
REPLACE CCFL LAMP
IN THE LCD MODULE
YES
YES
YES
YES

- 14 -
1. CHECK PIN122, 123
SOLDERING CONDITION
2. CHECK X501
3. TROUBLE IN U201
U201
POWER PIN8, 114
3.3V?
NO CHECK U801
U201
PIN122, 123
OSCILLATE AS
12MHZ?
CHECK CONNECTION LINE
FROM D-SUB TO U501
TROUBLE IN CABLE
OR LCD MODULE
YES
YES
YES
3. NO RASTER (OSD IS NOT DISPLAYED) –MST9011B
NO RASTER
(OSD IS NOT DISPLAYED)
U501
PIN43 IS 48KHz H-SYNC?
PIN44 IS 60Hz V-SYNC?
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
NO
NO

- 15 -
4. TROUBLE IN DPM
TROUBLE IN DPM
TROUBLE IN U501
CHECK PC
PC IS NOT GOING
INTO DPM OFF MODE
NO
CHECK H/V SYNC
LINE
NO
YES
YES
CHECK
R773, R775
(SYNC) ?
CHECK
U501 PIN 43.44
SYNC PULSE ?

- 16 -
EXPLODED VIEW
1
2
3
4
5
6
7
9
810
11

- 17 -
EXPLODED VIEW PARTS LIST
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
Part No.
3091TKL068A
3091TKL068Q
3091TKL068R
3091TKL068H
3091TKL068S
6304FLP068A
or 6304FLP092A
or 6304FLP074A
6304FCI002A
3809TKL047A
3809TKL047H
3809TKL047J
3043TKK122M
3043TKK122Q
3043TKK122S
6871TST393A
3313TL5084A
6871TPT271A
6631T11012R
6631T11012V
4951TKS104N
4814TKK236A
4814TKK237A
Description
CABINET ASSEMBLY, LS1515SL BRAND 3090TKL065 .. -L1515S
CABINET ASSEMBLY, L1515SL BRAND 3090TKL065 PC+ABS,SILVER -L1515S(S)
CABINET ASSEMBLY, L1515SL BRAND..BK PC+ABS, BK SPRAY -L1515S(K)
CABINET ASSEMBLY, L1515SL BRAND 3090TKL065(LG-LOGO) -L1515S(For PANAMA)
CABINET ASSEMBLY, L1515SL BRAND TKL065 SILVER SPRAY LIFE IS GOOD ABS -L1515S(S)(For AUSTRALIA)
LCD(LIQUID CRYSTAL DISPLAY), LM150X06-A4C3 LG PHILPS TFT COLOR LPL
LCD(LIQUID CRYSTAL DISPLAY), LM150X06-A4N6 LG PHILPS TFT COLOR LVDS 250NIT XGA
LCD(LIQUID CRYSTAL DISPLAY), LM150X06-A4K8 LG PHILPS TFT COLOR 5MASK
LCD(LIQUID CRYSTAL DISPLAY), M150X4-L06 CHIMEI TFT COLOR CMO 15"" TFT"
BACK COVER ASSEMBLY, L1515SL 3808TKL051 .. -L1515S
BACK COVER ASSEMBLY, L1515SL .. BK,PC+ABS" -L1515S(S),(K)
BACK COVER ASSEMBLY, L1515SL . BK,ABS -L1515S(S)(For AUSTRALIA)
TILT SWIVEL ASSEMBLY, L1515SL .. STAND ASSY+B/C ASSY -L1515S
TILT SWIVEL ASSEMBLY, L1515SL .. B/C:BK,PC+ABS" -L1515S(S),(K)
TILT SWIVEL ASSEMBLY, L1515SL BK.AB" -L1515S(S)(For AUSTRALIA)
PWB(PCB) ASSEMBLY, SUB, L1515SL CONTROL TOTAL BRAND CL-32
MAIN TOTAL ASSEMBLY, L1515SM BRAND CL-61
PWB(PCB) ASSEMBLY, POWER, 15" M-CHASSIS POWER TOTAL LIEN CHANG "A INTEGRATED LIPS"
CONNECTOR ASSEMBLY, 20P H-H 140MM UL20276 PANEL LINK CABLE LM567D -LG PHILPS TFT COLOR Module
CONNECTOR ASSEMBLY, 20P H-H 120MM UL20276 UNIXTAR LB500J -CHIMEI TFT COLOR Module
METAL ASSEMBLY, FRAME MULTI-FRAME(LPL, ACMO)_ANAOLOG
SHIELD, INVERTER WIRE SHIELD(TOP)
SHIELD, INVERTER SHIELD CAP(BOTTOM)

- 18 -
DATE: 2004. 2. 11.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C204 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C205 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C206 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C207 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C208 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C209 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C210 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C211 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C214 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C215 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C216 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C217 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C218 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C219 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C220 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C221 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C222 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C223 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C225 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C226 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C227 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C230 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C231 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C232 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C233 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C251 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C501 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C502 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C503 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C504 0CH8106F611 10UF 16V M 85STD(CYL) R/TP
C506 0CC030CK01A 3PF 1608 50V 0.25 PF R/TP NP
C507 0CC180CK41A 18PF 1608 50V 5% R/TP NP0
C508 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C701 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C703 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C708 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C709 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C710 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C711 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C717 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C718 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C719 0CC680CK41A 68PF 1608 50V 5% R/TP NP0
C720 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C721 0CC680CK41A 68PF 1608 50V 5% R/TP NP0
C727 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C732 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C733 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C734 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C735 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C760 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C801 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C803 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
DATE: 2004. 2. 11.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C804 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C805 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C806 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C807 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C808 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C809 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C810 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C812 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C814 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C815 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C816 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
D701 0DS226009AA KDS226 TP KEC SOT-23 80V 30
D702 0DS226009AA KDS226 TP KEC SOT-23 80V 30
D706 0DS226009AA KDS226 TP KEC SOT-23 80V 30
D707 0DD184009AA KDS184 TP KEC - 85V - - - 30
D804 0DD184009AA KDS184 TP KEC - 85V - - - 30
D805 0DD184009AA KDS184 TP KEC - 85V - - - 30
ZD701 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
ZD702 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
ZD703 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
ZD704 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
ZD705 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
ZD711 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
U201 0IPRPM3007B "MST9011B(ANALOG) MSTAR 128P,"
U501 0IZZTSZ358A MYSON 44P MTV312 L1515SM - E
U502 0ISG240860B M24C08W6 SGS-THOMSON 8SOP R/
U801 0IPMGKE011A KIA78D33F KEC DPAK R/TP 3.3V
U803 0IPMGK2001B AIC1117A-33CYTR(BS33) AIC SO
Q503 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q504 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q505 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q703 0TR390609FA KST3906-MTF TP SAMSUNG SOT2
Q704 0TR390609FA KST3906-MTF TP SAMSUNG SOT2
Q706 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q707 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q801 0TR127309AA KTA1273-Y(KTA966A) TP KEC TO
Q802 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
R201 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R202 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R203 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R207 0RJ3900D677 390 OHM 1/10 W 5% 1608 R/TP
R208 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
MAIN BOARD
CAPACITORS
ICs
DIODEs
TRANSISTOR
RESISTORs

DATE: 2004. 2. 11.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R209 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R210 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R213 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R214 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R220 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R506 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R508 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R512 0RJ2000D677 200 OHM 1/10 W 5% 1608 R/TP
R513 0RJ2000D677 200 OHM 1/10 W 5% 1608 R/TP
R514 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R515 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R516 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R518 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R519 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R520 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R521 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R522 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R523 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R524 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R525 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R526 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R527 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R528 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R529 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R531 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R532 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R534 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R535 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R537 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R541 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R542 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R543 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R544 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R545 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R546 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R547 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R548 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R549 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R555 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R556 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R557 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R560 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R561 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R563 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R564 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R565 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R701 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R703 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R706 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R708 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R709 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R716 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R717 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R722 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R723 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R724 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R725 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R726 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R727 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R728 0RJ1502D677 15K OHM 1/10 W 5% 1608 R/TP
R735 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R744 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
DATE: 2004. 2. 11.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R745 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R747 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R748 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R749 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R770 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R771 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R772 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R773 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R774 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R775 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R779 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R780 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TP
R781 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TP
R782 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP
R783 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP
R802 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R804 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R805 0RJ2000D677 200 OHM 1/10 W 5% 1608 R/TP
R806 0RJ2000D677 200 OHM 1/10 W 5% 1608 R/TP
R807 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R808 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R825 0RX0470J609 0.47 OHM 1 W 5% TA52
X501 6212AA2004A HC-49U TXC 12.0MHZ +/- 30 PP
LED1 0DLLT0089AA LITEON LTL-1BEDJ-0C2 TP GREE
R1 0RD4701Q609 4.70K 1/4W(3 5% TA52
R2 0RD4701Q609 4.70K 1/4W(3 5% TA52
R3 0RD1501Q609 1.50K 1/4W(3 5% TA52
R4 0RD1501Q609 1.50K 1/4W(3 5% TA52
R5 0RD3301Q609 3.30K 1/4W(3 5% TA52
R6 0RD3301Q609 3.30K 1/4W(3 5% TA52
R7 0RD9101Q609 9.10K 1/4W(3 5% TA52
SW1 140-058E SKHV10910B LGEC NON 12V 20A
SW2 140-058E SKHV10910B LGEC NON 12V 20A
SW3 140-058E SKHV10910B LGEC NON 12V 20A
SW4 140-058E SKHV10910B LGEC NON 12V 20A
SW5 140-058E SKHV10910B LGEC NON 12V 20A
SW6 140-058E SKHV10910B LGEC NON 12V 20A
SW7 140-058E SKHV10910B LGEC NON 12V 20A
ZD1 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 500
ZD2 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 500
- 19 -
OTHERs
CONTROL BOARD

SCHEMATIC DIAGRAM
- 20 -
1. SCALER
1