LG FLATRON L3000H User manual

MAIN
COLOR MONITOR
SERVICE MANUAL
Website:http://biz.LGservice.com
E-mail:http://www.LGEservice.com/techsup.html
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS NO. : CL-49
MODEL: L3000H(L3000HL-AL**A, AG**A)
( ) **Same model for Service

1. LCD CHARACTERISTICS
Type : TFT Color LCD Module
Size : 30inch
Pixel Pitch : 0.5025 x 0.1675 x RGB
Color Depth : 8-bit, 16,777,216 colors
Electrical Interface : LVDS
Active Display Area :
643.2mm x 385.92mm -LPL Module
: 683.6mm x 433.6mm -CMO Module
Surface Treatment :
Anti-Glare, Hard Coating(3H) -LPL Module
: Anti-Glare, Hard Coating(2H) -CMO Module
Operating Mode : Normally Black, Transmissive
Backlight Unit : 16-CCFL (Cold Cathode
Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥
10
Left : -80° min., -85°(Typ)
Right : +80° min., +85°(Typ)
Top : +80° min., +85°(Typ)
Bottom : -80° min., -85°(Typ)
2-2. Luminance : 380(min), 450(Typ)
-LPL Module
450(min), 500(Typ) -CMO Module
2-3. Contrast Ratio : 280(min), 350(Typ) -LPL Module
500(Typ) -CMO Module
3. SIGNAL (Refer to the Timing Chart)
3-1. PC & Video Input
1)Signal Input : S-video,RCA, Component
2)Input Form : D-SUB Analog, DVI-D,V1(CVBS)
V2(SVHS), DVD(Ycbcr),HDTV(YPbPr),
NTSC
3)Resolution(max) : Analog -1280 x 1024
Digital -1280 x 1024
3-2. Audio Signal
1) Input: PC : 700mVrms
AV : 450mVrms
2) Output: PC : 8W
AV : 8W
3-3. Sync Input
Horizontal : 30 ~ 66kHz(Digital: 30~63kHz)
Vertical : 56 ~ 85Hz
Input Form : Separate, TTL,
Positive/Negative Digital
4. POWER SUPPLY
4-1. Power Adaptor
Input : AC 100~240V, 50/60Hz , 2.0A
Output : DC 5V 0.9A, DC12V 1.5A
DC18V 1.0A, DC24V 5.0A
4-2. Power Consumption
5. ENVIRONMENT
6-1. Operating Temperature: 10°C~35°C (50°F~95°F)
6-2. Operating Humidity : 10%~80%
6-3. MTBF : 50,000 Hours(Min.)
6. DIMENSIONS
Width : 734 mm (28.90'')
Height : 99 mm (3.89'')
Depth : 538 mm (21.18')
7. WEIGHT
excl. Package : 14.2kg (31.31 lbs)
CONTENTS
SPECIFICATIONS
- 2 -
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 4
TIMING CHART ....................................................... 5
OPERATING INSTRUCTIONS ................................ 6
BLOCK DIAGRAM ................................................. 10
DESCRIPTION OF BLOCK DIAGRAM...................11
ADJUSTMENT ...................................................... 12
TROUBLESHOOTING GUIDE .............................. 14
WIRING DIAGRAM ............................................... 20
EXPLODED VIEW...................................................22
REPLACEMENT PARTS LIST ...............................24
SCHEMATIC DIAGRAM......................................... 34
MODE
POWER ON (NORMAL)
STAND-BY
SUSPEND
POWER OFF
CUT-OFF SWITCHOFF
H/V SYNC
ON/ON
OFF/ON
ON/OFF
OFF/OFF
-
POWER CONSUMPTION
less than 160 W
less than 5 W
less than 5 W
less than 5 W
less than 1 W
LED COLOR
GREEN
AMBER
AMBER
AMBER
OFF
VIDEO
ACTIVE
OFF
OFF
OFF
-

- 3 -
Signal Connector Pin Assignment
Pin Signal (DVI-D)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
T. M. D. S. Data2-
T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4-
T. M. D. S. Data4+
DDC Clock
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1-
T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3-
T. M. D. S. Data3+
+5V Power
Ground
(return for +5V,
H. Sync. and V. Sync.)
Pin Signal (DVI-D)
18
9
17 24
16
16
17
18
19
20
21
22
23
24
Hot Plug Detect
T. M. D. S. Data0-
T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5-
T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
T. M. D. S. (Transition Minimized Differential Signaling)
• DVI-D Connector (Digital)

- 4 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
•There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
•Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
•Must mount the module using mounting holes arranged
in four corners.
•Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
•Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
•Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
•Make certain that treatment person’s body are
grounded through wrist band.
•Do not leave the module in high temperature and in
areas of high humidity for a long time.
•The module not be exposed to the direct sunlight.
•Avoid contact with water as it may a short circuit within
the module.
•If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
•If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
•Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
PRECAUTION
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

TIMING CHART
- 5 -
VIDEO
SYNC
B
D
CFE
A
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H + 31.469 800 640 16 96 48
V–70.8 449 350 37 2 60
H–43.269 832 640 56 56 80
V–85.0 509 480 1 3 25
H–31.469 800 640 16 96 48
V–59.94 525 480 10 2 33
H–37.5 840 640 16 64 120
V–75 500 480 1 3 16
H–31.468 900 720 18 108 54
V + 70.8 449 400 12 2 35
H + 37.879 1056 800 40 128 88
V + 60.317 628 600 1 4 23
H + 46.875 1056 800 16 80 160
V + 75.0 625 600 1 3 21
H + 53.674 1048 800 32 64 152
V + 85.061 631 600 1 3 27
H+/–49.725 1152 832 32 64 224
V+/–74.55 667 624 1 3 39
H–48.363 1344 1024 24 136 160
V–60.0 806 768 3 6 29
H–60.123 1312 1024 16 96 176
V–75.029 800 768 1 3 28
H + 63.981 1688 1280 48 112 248
V + 60.02 1066 1024 1 3 38
H + 47.7 1680 1280 66 134 200
V + 60 795 768 1 3 23
Mode H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
25.175
28.321
25.175
31.5
36.0
40.0
49.5
56.25
57.283
65.0
78.75
108.0
80.14
640x350
70Hz
640x480
85Hz
640x480
60Hz
640x480
75Hz
720x400
70Hz
800x600
60Hz
800x600
75Hz
800x600
85Hz
832x624
75Hz
1024x768
60Hz
1024x768
75Hz
1280x1024
60Hz
1280x768
60Hz
Sync
Polarity Frequency
Dot
Clock Total Period
(E)
Video Active Time
(A)
Sync Duration
(D)
Back Porch
(F)
Front Porch
(C)
Resolution

- 6 -
FRONT VIEW
REAR VIEW CONNECTOR PANEL
REAR VIEW
OPERATING INSTRUCTIONS
Front Control Panel(P7)
RS-232C
RS-232C
Theft prevention
locking device Theft prevention
locking device
1. RS-232CTerminal
:TheRS-232Cprotocolisusedforcommunication
betweenthePCandmonitor.Youcanturnthe
monitoron/off,seslectaninputsourceoradjustthe
OSDmenufromyourPC.
ThecableforRS-232Cterminalconnectionisnotan
accessoryincludedintheproduct.
Pleasepurchase thecable.
2.DVIDigitalSignalConnector
3.D-SUBAnalogSignalConnector
4. Connectthepowercord
5. SpeakerTerminal:Connectthespeaker
PC Audio InputTerminal
-Connect the audio cable
to the LINE OUT jack in the
PC sound card
Headphone/earphone
ConnectionTerminal
S-VideoInput Terminal
AVOutput Terminal
(Audio)
DVDInput Terminal
AVInput Terminal(Audio)
AVOutput Terminal
(Video)
AVInput Terminal(Video)
HDTVInput Terminal
MAIN

- 7 -
OPERATING INSTRUCTIONS
Front Control Panel
MAIN
MAIN
7
2
1568 3 4
•Press the button to turn on the power. Press the button again to turn it off.
•This Indicator lights up green when the display operates normally. If the display is in
DPM (Energy Saving) mode, this indicator color changes to amber.
Power Button
Power (DPMS)
Indicator
Adjust the volume
•Use this button to directly control
brightness and contrast of the PC signal
(DSUB/DVI).
•Use this button toshow/hide the OSD(on Screen Display) menu screen.
MENU Button
• Use the button to select an icon or adjust the setting in the OSD screen .
OSD Buttons
[For DSUB signal]
•Select the icon to adjust on the OSD screen.
•If you press the [AUTO/SELECT] button,
automatic screen adjustment will be started.
AUTO/SELECT Button
1
2
3
4
5
6
8
7
Use this button to lock/unlock OSD screen adjustment.
(Activated when pressed together longer than 5 seconds.)
• Use this button to select an input signal.
•DVI DIGITAL: DVI digital signal
•DSUB ANALOG: 15-pin D-sub analog signal
•VIDEO1 (CVBS): Composite video
•VIDEO2 (S-Video): S-video
•DVD(Y, Cb, Cr): DVD
•HDTV(Y, Pb, Pr): HD television
SOURCE
Button
CONTROLS LOCKED/UNLOCKED :
MENU and
•The unit that receives the signal from the remote controller.
Main Power Switch
AUTO/SELECT
SOURCE
[Other signals that DSUB]
•The current signal and mode information will
be displayed.
•Use this button to turn on/off the monitor.
• OSD is locked
• OSD is unlocked.

- 8 -
Remote Controller Buttons
Power On/Off Button
• Input Select Button
•
AV Button
(See next page)
Sleep Button
When watching AV/DVD/HDTV
- The monitor will be automatically turned off
after a certain period of time.
Press this button repetitively to select an
appropriate time duration
PSM Button
When watching AV/DVD/HDTV
- Automatically adjusts the image.
Press this button repetitively to set the
intended screen.
CAPTION Button
- (Only U.S.A)
There is not a function
which is supported
• Menu Button
• Exit Button
Auto Channel Button
PC: Automatic adjustment function
(Operational for the analog signal only)
There is not a function
which is supported
Check Button
Sound Mode Select
Select the sound mode:
MONO/STEREO
Video Operation Button
Applicable for LG products only
Volume Button
Mute button

- 9 -
1. PIP (Picture in Picture) Button
The sub-screen moves to the next mode whenever you press this button.
: Small -> Large -> Off
2. POP (Picture out Picture) Button
The sub-screen moves to the next mode whenever you press this button.
: POP ON -> PBP(FULL) -> PBP(4:3) -> OFF
If you press the button once,
the following Input Signal
Window will appear. Select
the signal type you want
using the button.
This button will be enabled only
when you selected the AV signal.
The signal type will be changed
with the following order. Set the
signal type you want.
POP ON PBP (FULL) PBP (4:3)
• Input Select Button
• AV Button
3. Swap Button
You can swap the main screen and the sub-screen when the PIP/POP/PBP
function is used..
When 'Input Signal 1' comes on in the main screen, only
'Input Signal 2' can be displayed on the sub-screen. On the
contrary, if the main screen displays 'Input Signal 2', the sub-
screen can display 'Input Signal 1' only. You can swap 'Input
Signal 1' and 'Input Signal 2' using the SWAP button.
<Tableof PIP/POP/PBP Function Support>
VIDEO1 VEDIO2 DVD HDTV
SWAP
SWAP
PIP
POP
PBP

- 10 -
DVI-D
D-SUB
CVBS Out
S/W
(CXA2040AQ)
DC/DC
Regulator
LCD
Module
12V
5V 3.3V
128Mb
DDR
SDRAM
(HY5DU283222Q4)
EEPROM
System
8V
2.5V
Y/C-in
H/ V Sync
3.3V
2.5V
2.5V
12V
Data (FSD0 ..31) (FSA0 ..11)
PCB_PWR
Only USA
INV_PWR LCM_PWR AMP_PWR
Control Signals
R,G,B
Even
RGB
Format Converter
Circuit
YPbPr
CVBS 2(Tuner)
CVBS Audio
Out
CVBS Out
1.8V
Built-in
Power
24V
(LPL)
5V 12V
(CMO)
4Mb Flash
Memory
(29LV040B)
Data (OCMD 0..7) (OCMA 0..19)
3.3V
1.8V
Serial
Port
H/ V Sync
MAX232C RXD
TXD
Video Signal
Processor
(gm1501)
Caption/V-Chip (M37136)
64Mb
SDRAM
(HY57V643220)
PCB_PWR INV_PWR LCM_PWR AMP_PWR
Analog Signal
Analog
Switch
(BA7657F)
Digital Signal
YUV
Deinterlacer
(FLI2310)
HDTV
EEPROM
DDC-A
EEPROM
DDC-D
Video Signal
3D CombFilter
(UPD64083)
Video
Decoder
(VPC3230)
Y/C-out
CVBS PAL
C-out
16 Bit
24Bit
Y/Cb/Cr
DVD
Video Out
CVBS 1 Y-out
Video Filter(5.2Mhz)
SP (R)
Audio
Decoder
(MSP3420G)
Audio
Amp
(TPA3004D2)
TPA6110
VAROUTR/L
PC Audio
DTV Audio
DVD Audio
CVBS Audio
BLOCK DIAGRAM

- 11 -
DESCRIPTION OF BLOCK DIAGRAM
1. Input Selection Circuit
1) Analog Input Selection
This block is composed of BA7657F(U103) and
peripheral devices.
There are analog H/V Syncs. BA7657F IC chooses one
input and outputs selected input through sync selection
pin (Pin 1).
2) Video Input Selection
This block is composed of video S/W IC (CXA2040Q,
U3) and peripheral devices. There are three inputs in
CXA2040Q IC(CVBS video signal through RF tuner,
video input CVBS, S-video signal). One selected video
signal is transmitted a video decoder IC (VPC3230, U1)
2. DDC controller
This block is composed of GM1501(U402) and
peripheral EEPROM IC(U107,U108).
GM1501(U402) controls peripheral devices through IIC
line.
Major functions are (1) to control Flash memory
through DDC-SCLA, DDC-SDAA of D-sub and (2) to
store EDID data in the EEPROM (U107,U108).
3. Video Decoder
This block is composed of VPC 3230 (U1) and
peripheral devices.
GM 1501 controls this IC through IIC Line.
This IC analyzes input signal of CVBS, Y/C and output
analyzed signal (8bit interlace signal) to De-interlace
block.
Analyzed signal has video control signals like Contrast,
Brightness, Sharpness, Color, tint signals Including
Adaptive Comb Filter.
4. Audio Decoder
This block is composed of MSP3420G (U503) and
peripheral devices.
GM 1501 controls this IC through IIC Line.
This IC analyzes audio input signal through A/V Jack
and PC audio.
The analyzed signals transmitted to audio amplifier
(TPA3004, U505).
5. Audio Amplifier
This block is composed of TPA3004 (U505) and
peripheral devices.
The function of the audio amplifier is that to amplify
audio L/R signal transmitted from audio decoder. The
audio signal is amplified according to pre-defined DC
volume control curve. Also, Headphone
amplifier(Tpa6110, U501) is controlled through Line-
out.
6. De-interlacer
This block is composed of FLI 2310(U301) and
peripheral devices.
GM1501 (U402) controls this IC through IIC Line.
And this IC converts 8 Bit Interlaced Y/UV signal to De-
interlaced signal.
It output converted signal to Format Converter IC(GM
1501, U402).
7. Format Converter
This block is composed of GM 1501(U402) and
peripheral devices. GM 1501(Scaler,U402) contains
MICOM.
1) This IC contain A/D converter, Pre-amp and PLL
circuit that converting analog video signal(0.7Vp-p)
through D-sub(J103) Pin to digital signal.
2) This IC Decode TMDS signals of 8 line from DVI-D
Pin (J202) and transmit to LVDS Transmitter.
GM 1501 is Format Converter IC that receives Digital
signal and outputs proper frame signal to LCD Module
Timing(1280x768,WXGA).
8. DC/DC Converter block
DC/DC Converter convert the input 12V, 24V to proper
2.5V, 3.3V, 5V, 1.8V for main control system.
For shooting heat trouble, we use the DC/DC
converting IC.
9. Caption/V-CHIP block -Only U.S.A
This block is composed of M37136(U202) and
peripheral devices. M37136 IC is useful for channel
selection system for TV with a closed caption decoder.
It receives text information signal and displays text
information through text receiver decoder. It called
multi-text broadcast.
10. Power Supply Block
This Block generates DC Voltages(12V, 24V) to Main
Control system from AC Power(100-240 V, 50/60 Hz,
1.0 A).
This Circuit contains PFC(Power Factor correction)
circuit.
The Minimum of Power efficiency is about 75%.

- 12 -
DVI-D Connector
RS-232C EXT.
220
IBM
Compatible PC
Parallel Port
Power inlet (required)
Power LED
ST Switch
Power Select Switch
(110V/220V)
Control Line
Not used
RS232C
PARALLEL
V-SYNC POWER
ST
VGS MONITOR
E
V-Sync On/Off Switch
(Switch must be ON.)
F
A
B
C5V
E
F
A
B
C
1510
5
569
1
1
1
14
13
25
6
5V
5V
4.7K
4.7K
4.7K
74LS06
74LS06
OFF ON
OFF
ON
11
Figure 1. Cable Connection
ADJUSTMENT
Windows EDID V1.0 User Manual
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Don’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available to LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys”file to
“c:\WINNT\system32\drivers”folder
b) Run Userport.exe
c) Remove all default number
d) Add 300-3FF
e) Click Start button.
f) Click Exit button.
2. EDID Read & Write
1) Run WinEDID.exe
2) Edit Week of Manufacture, Year of Manufacture,
Serial Number
a) Input User Info Data
b) Click “Update”button
c) Click “Write”button

- 13 -
123CONTRAST
ADJUSTMENT
123BRIGHTNESS
COLOR
1. Input Analog signal through D-sub.
2. Press MENU Key and 3, 0, 2, 0 Num.key
NVRAM INITIAL
MICOM VERSION Ver. 49
VCHIP TEST
OFF
OFF
L3000HLMODEL
ELAPSED TIME 21 H
WB 0
SETUP
NVRAM INITIAL
MICOM VERSION Ver. 49
VCHIP TEST
OFF
OFF
L3000HLMODEL
ELAPSED TIME 21 H
WB 0
SETUP
NVRAM INITIAL
MICOM VERSION Ver. 49
VCHIP TEST
OFF
OFF
L3000HLMODEL
ELAPSED TIME 21 H
WB 1
SETUP
3. Then move SETUP. You can see SVC OSD.
ADJUST WHITE BALANCE
4. Press Down key to move WB 5. Input Full Black signal through D-Sub and the
number beside WB changes 1
NVRAM INITIAL
MICOM VERSION Ver. 49
VCHIP TEST
OFF
OFF
L3000HLMODEL
ELAPSED TIME 21 H
WB 2
SETUP
7. Input Full White signal through D-Sub and PRESS
RIGHT Key.
8. The number beside WB changes 2.
White balance adjustment is over.

- 14 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK POWER BOARD
CHECK J601
VOLTAGE
(18V, 12V, 5V)?
NO
CHECK POWER BOARD
CHECK
J602 VOLTAGE
(LPL: 24V,
CMO: 12V) ?
NO
CHECK KEY
CONTROL BOARD
YES
YES
YES
YES
CHECK X401
CHECK
X401
(14.318MHz) ? NO
CHECK MICOM(U402)
SUB POWER PORT(R419)
CHECK
J601
(SUB POWER) ? NO

- 15 -
2. NO RASTER(OSD IS NOT DISPLAYED)
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK THE PERIPHERAL
IC U402
CHECK U402? NO
CHECK THE PERIPHERAL
IC U402
CHECK
LVDS OUTPUT
(J403)?
NO
CHECK INVERTER
YES
YES
YES
YES
CHECK U604 AND THE
PERIPHERAL IC U604
CHECK
INVERTER POWER
(LPL: J604, J605
CMO: J606, J607) ?
NO

- 16 -
3. NO RASTER ON VIDEO SIGNAL INPUT
NO RASTER ON VIDEO SIGNAL
CHECK CABLE OF
VIDEO/COMPONENT
CHECK THE PERIPHERAL
UPD64083(U6)
CHECK THE PERIPHERAL IC
OF VPC3230(U1)
CHECK THE PERIPHERAL IC
OF VPC3230, FLI2310, SDRAM
CHECK THE PERIPHERAL IC
OF GM1501(U402)
CHECK UPD64083(U6)I/O
SIGNAL
CHECK VPC3230(U1) I/O
SIGNAL
CHECK FLI2310(U301) AND
SDRAM(U302) I/O SIGNAL
CHECK GM1501(U402)AND
SDRAM(U401)
POWER CHECK OF CXA2040(U3) : L3(9V)
POWER CHECK OF UPD64083(U6) : U5(3.3V), L17(2.5V)
POWER CHECK OF FLI2310(U301) : L307(3.3V), L302(3.3V), L308(1.8V), L301(1.8V)
POWER CHECK OF GM1501(U402)
NO INPUT SIGNAL
NO INPUT SIGNAL
NO OUTPUT SIGNAL
NO INPUT SIGNAL
NO OUTPUT SIGNAL
NO INPUT SIGNAL

- 17 -
4. SOUND TROBLE SHOOTING
NO SOUND OUTPUT
CHECK SOUND OF VCR,DVD,PC
(TV)CHECK OF CONNECTION OF
TUNER AND ANTENNA
CHECK THE PERIPHERAL IC
OF MSP3420G(U503)
CHECK THE PERIPHERAL IC
OF TPA3004(U505)
CHECK CONNECTION OF
SPEAKER ON MONITOR
CHECK SOUND INPUT
=>PC SOUND(J804)
=>VIDEO, DVD, DTV SOUND
(RED, WHITE OF J809, J808)
CHECK THE PERIPHERAL IC OF
MSP3420G(U503)
CHECK MSP3420G(U503) I/O SIGNAL
CHECK TPA3004(U505) I/O SIGNAL
CONNECTOR CHECK
POWER CHECK OF MSP3420G(U503) : L514(8V), L509(5V), L512(5V)
POWER CHECK OF TPA3004(U505) : C587(18V)
NO OUTPUT SIGNAL
NO OUTPUT SIGNAL
NO INPUT SIGNAL
NO INPUT SIGNAL
NO INPUT SIGNAL

- 18 -
5. NO RASTER STATE ON ANALOG SIGNAL
NO RASTER ON ANALOG SIGNAL
CONNECTOR(J103) CHECK
CHECK THE PERIPHERAL IC
OF GM1501(U402)
CHECK THE PERIPHERAL IC
OF GM1501(U402)
CHECK THE PERIPHERAL IC
OF GM1501(U402)
CHECK THE PERIPHERAL IC
OF D-SUB(J103)
CHECK I/O SYNC OF BA7657(U103)
CHECK ADC I/O SIGNAL IN
GN1501(U402)
CHECK GM1501(U402) I/O SIGNAL
CHECK LVDS I/O SIGNAL
POWER CHECK OF BA7657(U103) : L102(5V)
POWER CHECK OF GM1501(U402)
POWER CHECK OF LVDS OUTPUT: J403
NO OUTPUT SIGNAL
NO INPUT SIGNAL
NO OUTPUT SIGNAL
NO INPUT SIGNAL
NO OUTPUT SIGNAL
NO INPUT SIGNAL

- 19 -
6. NO RASTER STATE ON DIGITAL SIGNAL
NO RASTER STATEON DIGITAL SIGNAL
CONNECTOR(J102) CHECK
CHECK THE PERIPHERAL IC
OF GM1501(U402)
CHECK THE PERIPHERAL IC
OF GM1501(U402)
CHECK GM1501(U402) I/O SIGNAL
CHECK LVDS I/O SIGNAL
POWER CHECK OF GM1501(U402)
POWER CHECK OF LVDS OUTPUT: J403
NO OUTPUT SIGNAL
NO OUTPUT SIGNAL
NO INPUT SIGNAL
NO INPUT SIGNAL

- 20 -
WIRING DIAGRAM(LPL Module)
CN1
CN1
J503
J506
J602
J108
J601
J604
J605 J401
J402
J201
J505
J801
J802
J803
J804
Connector Ass’y P/N:
6631T11016A
Connector Ass’y P/N:
6631T20029C
Connector Ass’y P/N:
6631T20028D
Connector Ass’y P/N:
6631T20028C
Connector Ass’y P/N:
6631T12002P
Connector Ass’y P/N:
6631T12002N
Connector Ass’y P/N:
6631T20029B
Connector Ass’y P/N:
6631T20028E
Connector Ass’y P/N:
6631T20028B