Lg Mt-42pz40/v/b/r/s User manual

PLASMA MONITOR

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : RF-02RA

MODEL : MT-42PZ40/V/B/R/S

MODEL : MT-42PZ41/V/B/R/S/VB

MODEL : MT/MZ-42PZ42/V/B/R/S

MODEL : MT/MZ-42PZ43/V/B/R/S/VS

website:http://biz.LGservice.com

e-mail:http://www.LGEservice.com/techsup.html

Jan., 2003

Printed in KoreaP/NO : 3828VD0129E

- 2 -

CONTENTS

SAFETY PRECAUTIONS ...................................................................................3

DESCRIPTION OF CONTROLS ........................................................................ 4

SPECIFICATIONS .............................................................................................. 7

ADJUSTMENT INSTRUCTIONS ......................................................................10

BLOCK DIAGRAM.............................................................................................13

ASSEMBLY METHOD........................................................................................14

EXPLODED VIEW..............................................................................................16

EXPLODED VIEW PARTS LIST ........................................................................17

REPLACEMENT PARTS LIST...........................................................................18

SCHEMATIC DIAGRAM ........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in

the Schematic Diagram and Replacement Parts List.

It is essential that these special safety parts should be replaced with the same components as recommended in this manual to

prevent X-RADIATION, Shock, Fire, or other Hazards.

Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during

the servicing of a receiver whose chassis is not isolated from

the AC power line. Use a transformer of adequate power rating

as this protects the technician from accidents resulting in

personal injury from electrical shocks.

It will also protect the receiver and it's components from being

damaged by accidental shorts of the circuitry that may be

inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replace

it with the specified.

When replacing a high wattage resistor (Oxide Metal Film

Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,

extreme care should be used in handling the Picture Tube.

Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source,

connect an electrical jumper across the two AC plug prongs.

Place the AC switch in the on position, connect one lead of

ohm-meter to the AC plug prongs tied together and touch other

ohm-meter lead in turn to each exposed metallic parts such as

antenna terminals, phone jacks, etc.

If the exposed metallic part has a return path to the chassis, the

measured resistance should be between 1MΩ and 5.2MΩ.

When the exposed metal has no return path to the chassis the

reading must be infinite.

An other abnormality exists that must be corrected before the

receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor

between a known good earth ground (Water Pipe, Conduit, etc.)

and the exposed metallic parts.

Measure the AC voltage across the resistor using AC

voltmeter with 1000 ohms/volt or more sensitivity.

Reverse plug the AC cord into the AC outlet and repeat AC

voltage measurements for each exposed metallic part. Any

voltage measured must not exceed 0.75 volt RMS which is

corresponds to 0.5mA.

In case any measurement is out of the limits specified, there is

possibility of shock hazard and the set must be checked and

repaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument's

exposed 

METALLIC PARTS

Good Earth Ground

such as WATER PIPE,

CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

- 4 -

DESCRIPTION OF CONTROLS

Connection to PC

Note: All cables shown are not provided with the Monitor, except:

A D-sub 15 pin cable and DVI cable is supplied to connect the Monitor to a PC.

Connection to AV equipment

( )( )

R

( )( )

L

REMOTE

CONTROL

RGB2 INPUT

(DIGITAL RGB INPUT)

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

LOCK

CONTROL

ON/ OFF

YP

B

P

R

(MONO)

R

AUDIO

L

R

AUDIO

L

S-VIDEO

VIDEO INPUT

AC INPUTAUDIO INPUTAUDIO INPUT

COMPONENT(480i/480p)

(DVD INPUT)

RGB1 INPUT

(PC INPUT)

RGB1 OUTPUT

(PC OUTPUT)

AUDIO INPUT

VOL.MENU

INPUT 

SELECT

ON/OFF



Main Power Button INPUT SELECT Button

VOLUME (F,G) Buttons

Power Standby Indicator

Illuminates red in standby mode,

Illuminates green when the

Monitor is turned on

Remote Control Sensor

MENU Button

D,EButtons

AUDIO

INPUT

VIDEO INPUT

S-VIDEO

INPUT

COMPONENT

AUDIO INPUT

RS-232C

INPUT

RGB2 INPUT

(DIGITAL

RGB INPUT) RGB1

INPUT

(PC

INPUT)

RGB AUDIO

INPUT

COMPO-

NENT(480i/480p)

(DVD INPUT)

- 5 -

( )( )

R

( )( )

L

REMOTE

CONTROL

RGB2 INPUT

(DIGITAL RGB INPUT)

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

LOCK

CONTROL

ON/ OFF

AC INPUT

RGB1 INPUT

(PC INPUT)

RGB1 OUTPUT

(PC OUTPUT)

AUDIO INPUT

AV1AV1

RCA Type

Scart Type

5

( )( )

R

( )( )

L

REMOTE

CONTROL

RGB2 INPUT

(DIGITAL RGB INPUT)

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

LOCK

CONTROL

ON/ OFF

Y P

B

P

R

(MONO)

R

AUDIO

L

R

AUDIO

L

S-VIDEO

VIDEO INPUT

AC INPUTAUDIO INPUTAUDIO INPUT

COMPONENT(480i/480p)

(DVD INPUT)

RGB1 INPUT

(PC INPUT)

RGB1 OUTPUT

(PC OUTPUT)

AUDIO INPUT

1 2 3 64 5

1. EXTERNAL SPEAKER (8 ohm output)

Connect to optional external speaker(s).

*For further information, refer to ÔSpeaker & Speaker StandÕ

manual.

2. RS-232C INPUT(CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

3. RGB2 INPUT(DIGITAL RGB INPUT)/RGB1 INPUT(PC

INPUT)/AUDIO INPUT SOCKET

Connect the monitor output socket of the PERSONAL COM-

PUTER to this socket.

RGB1 OUTPUT(PC OUTPUT) SOCKET

You can watch the RGB1 signal on another monitor, connect

RGB1 OUTPUT (PC OUTPUT) to another monitorÕs PC

input port. When the monitor is in standby mode, you can not

watch the RGB1 signal on another monitor.

4. CONTROL LOCK Switch

REMOTE CONTROL

When ÒCONTROL LOCKÓ is set ÒONÓ, Monitor is operated by

the external control device.

5. AUDIO / COMPONENT(480i/480p)(DVD INPUT) / S-VIDEO

/ VIDEO INPUT / AUDIO INPUT SOCKETS

EURO SCART SOCKET

Note : The interface board(AP-42EA40/41) is not equipped

on MT/MZ-42PZ42/43 series models. Contact your dealer

for buying this optional item.

6. POWER CORD SOCKET

This Monitor operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to operate

the Monitor on DC power.

- 6 -

-When using the remote control aim it at the remote control sensor of the Monitor.

- There's maybe a defect in consecutive operation of remote control in specified brightness according to this monitor

feature.

¥Open the battery compartment cover on the back side and

insert the batteries with correct polarity.

¥ Install two 1.5V alkaline batteries of AAA type. DonÕt mix used

batteries with new batteries.

Installing Batteries

1 2 3

4 5 6

7 8

0

9

POWER

SLEEP INPUT SELECT

PSM SSM

ARC

AUTO CONFIG.

ZOOM -

ZOOM +

SPLIT ZOOM

MENU MUTE

OK

VOL

POWER STOP

PLAY FF

REC

REW

P/STILL

PIP

TWIN PICTURE

PIP POSITION

PIP STILL

SOUND SELECT

PIP INPUT

VOL

CHILD LOCK

POWER

Switches the Monitor on from stand-

by or off to standby.

SLEEP

Sets the sleep timer.

PSM

Adjusts the factory preset picture

according to the room.

ARC

Changes the picture format.

ZOOM-

Reduces the main picture size.

SPLIT ZOOM

Enlarge the screen with regular

MENU

Displays on screen menus one by one.

Exits the current menu.

Memorizes menu changes.

NUMBER buttons

PIP

Switches the sub picture on

TWIN PICTURE

PIP INPUT

Selects the input mode for the

sub picture.

SOUND SELECT

Select main picture sound or

sub picture sound for PIP.

PIP POSITION

change the sub picture position.

PIP STILL

Freeze sub picture motion.

VCR BUTTONS

Controls a LG video cassette

recorder.

OK

DD/ EE

Selects a menu option.

FF/ GG(Volume button)

Increases/decreases sound level.

Adjusts menu settings.

INPUT SELECT

SSM

To select the sound appropriate to

your viewing program character:

Flat,Speech,Movie,Music, or

User

AUTO CONFIG.

CHILD LOCK

To operate the monitor with remote

control only.

MUTE

Switches the sound on or off.

ZOOM+

Enlarges the main picture size.

- 7 -

SPECIFICATIONS

NOTE : Specifications and others are subject to change without notice for improvement

.

FScope

This specification can be applied to all model of 42ÓPDP

MONITOR related to RF-02RA Chassis.

FTest Condition

1) Temperature : 20¡5¡C

2) Relative Humidity: 65¡10%

3) Power Voltage:Standard Input Voltage

(AC 100V-260V,~50/60Hz)

Rated Voltage(AC 100V-260V,~50/60Hz)

But Standard input voltage mark value is marked by model.

4) Follow each drawing or spec for spec and performance of

parts,based upon P/N of B.O.M

5)

Warm up set for more than 15min before the

measurement.

FTest and Inspection Method

1) Performance:Follow the Standard of LG TV test

2) Standards of Etc requirement

Safety: Follow the standard of UL1950,CSA1950

EMC: FCC PART 15 CLASS A/B(40: ClassB; 41,43: ClassA)

Appliance

OK

TEST,Not Applied

OK

Remark

Safety: IEC950,EN60590

EMC:

Safety: EN60590

EMC: CE

Model Name

MT-42PZ40/41

/42/43

MZ-42PZ42/43

Market

N-EU,China

EU

Chassis

RF-02RA

Brand

LG

Model Name

MT-42PZ40/41/42/43

MZ-42PZ42/43

Market Place

N-EU, China

EU

Remark

Industry/Home use

- 8 -

FFeature and Function

No Item Specification Remark

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Remote controller Code

External Control

RGB1 Input

RGB2 Input

RGB Audio input

RGB1 Output

Component input

Component Audio input

AV Input

S-video input

External Speaker Output

Auto Picture mode

User control

DASP

AVL

PIP(Picture In Picture)Mode

DW Mode

NEC Code

RS-232C

RGB-DTV,RGB-PC(Analog)

RGB-DTV(DVI),RGB-PC(Digital)

L/R

RGB-DTV,RGB-PC Throughout

Y,CB/PB,CR/PR

L/R

Video/L/R

Y/C

L/R

Clear/ Soft/ User

Contrast/ Brightness/ Color/ Tint/

Sharpness/ Color Temperature

Flat/ Sports/ Cinema/ Music/ User

On/ Off

O

D-Sub 9 pin

D-Sub 15 pin

Earphone Jack

D-Sub 15pin

Video:BNC Jack,SCART1/2(MZ-42PZ43)

Spk terminal

Tint: Only NTSC-M

1)Main screen:RGB_PC/DVI

2)Sub screen: COMPONENT/AV/

S-VIDEO(480i),RGB-DTV(480P,720P,1080I)

Feature

Picture

Sound

1

2

FGeneral Specification

No Item Specification Remark

Video input

applicable system

Input Voltage

Screen Size

Aspect Ratio

PDP Module

Screen Filter

Operating Environment

Storage Environment

1

2

3

4

5

6

7

8

NTSC-M/PAL/SECAM/NTSC4.43(MT,MZ)

MT-42PZ40/41/42/43: 110V -240V 50Hz

MZ-42PZ42/43: 200V -240V 50Hz

42 inch

16:9 (wide)

PDP42WVSN4

Transmissivity: 45%

1)Temp: 0 ~ 40 deg

2)Humidity: 80% under

1)Temp: -20 ~ 60 deg

2)Humidity: 85% under

PDP

LGE

Maker: NBK

O

16:9, 4:3, Zoom

Noise Reduction(YNR)

Film Mode

Motion detection

Sleep Timer

Orbiter

White Wash

Display Mode

- 9 -

No Item Specification Remark

17

18

19

20

21

22

23

AV,Component 480i

Afterimage Prevention

(left,bottom,right,top,top,right,bottom,left)

Afterimage Remove

480i/p,720p,1080i

: 16:9, 4:3, Zoom

PC(Analog/Digital)

: 4:3, 16:9

FSafety and Regulation

No Item Remark

1

2

Power Consumption,Max

Power Consumption,Stand by

300

Min Typ UnitMax

350 400

6

W

IEC950

FExternal Interface

No Item Remark

1

2

3

4

5

6

7

8

9

10

11

12

Video Input Level

Video Input Frequency Response

Video Input S/N

S Video Input Level(Y)

S Video Input Level(C-BURST)

Audio Input Level

Audio Input Frequency Response

Audio Input S/N

Audio Input Distortion

Audio Input Dynamic Range

Component Video Input Level

(Y,CB/PB,CR/PR)

R/G/B Video Input Level

0.9

5

40

0.85

0.143

0.3

0.08

40

2

0.6

Min Typ UnitMax

1

0.4

0.7

1.1

1.15

0.286

0.5

7

2

0.8

Vpp

MHz

dB

Vpp

Vrms

kHz

dB

%

V

Vpp

Video Valuation

NTSC/PAL

Video Valuation, 75 ohm

(480i,480p,720p,1080i)

75ohm

1. Application Object

These instructions are applied to all of the PDP monitor, RF-

02RA.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.

(3) The adjustment must be performed in the circumstance of

25±5¡C of temperature and 65±10% of relative humidity if

there is no specific designation.

(4) The input voltage of the receiver must keep 110~240V,

50/60Hz in adjusting.

(5) The receiver must be operated for about 15 minutes prior

to the adjustment.

¤After receiving 100% white pattern, the receiver must be

operate prior to adjustment.(Or white condition in HEAT-

RUN mode)

¤ŁEnter into HEAT-RUN mode

- Select the HEAT-RUN OFF by pressing ADJ Key on

Remote Control for adjustment.

- Press the VOL + Key in HEAT-RUN OFF.

(OSD display HEAT-RUN WHITE and screen display

100% FULL WHITE PATTERN)

[Set is activated HEAT-RUN without signal generator in

this mode.

[Single color pattern of HEAT-RUN mode uses to check

PANEL.(RED/BLUE/GREEN)

[Caution] If you turn on a still screen more than 20 minutes, a

afterimage may be occur in the black level part of the

screen.

Each PCB Assy must be checked by the Check JIG Set before

whole assembly. (Be careful the POWER PCB Assy not to

damage to PDP Module)

3. POWER PCB Assy Voltage Adjustment

(Va, Vs, -Vy, Vsetup Voltage Adjustment)

3-1. Test Equipment

D.M.M 1EA

3-2. Connection Diagram for Measuring

Refer to Fig 1.

3-3. Adjustment Method(POWERWELL)

(1) Va Adjustment

¤Connect pin 1 of CN205 to (+) jack of D.M.M.

¤ŁAfter turning the VR3(Va ADJ), voltage of D.M.M

adjustment as same as Va voltage which on label of

panel right/top.(Deviation : ±0.5V)

(2) Vs Adjustment

¤Connect pin 1 of CN207 to (+) jack of D.M.M.

¤ŁAfter turning the VR6(Vs ADJ), voltage of D.M.M adjust

as same as Vs voltage which indicated on label of panel

right/top.(Deviation : ±0.5V)

(3) -Vy Adjustment

¤Connect pin 1 of CN208 to (+) jack of D.M.M.

¤ŁAfter turning the VR5(-Vy ADJ), voltage of D.M.M adjust

as same as -Vy voltage which indicated on label of

panel right/top.(Deviation : ±0.5V)

(4) Vsetup Adjustment

¤Connect pin 5 of CN208 to (+) jack of D.M.M.

¤ŁAfter turning the VR4(Vsetup ADJ), voltage of D.M.M

adjust as same as Vsetup voltage which indicated on

label of panel right/top.(Deviation : ±0.5V)

[Refer to Typical Voltage

1. Va : 35 ~ 45V

2. Vs : 170 ~ 185V

3. -Vy : -60 ~ -90V

4. Vsetup : 210 ~ 240V

[Replace PDP Module or Power Board, adjust certainly Power

PCB Assy Voltage.

- 10 -

ADJUSTMENT INSTRUCTIONS

<Fig 1> Connection Diagram of POWERWEL Power Adj. for

Measuring

3-4. Adjustment Method(SONY)

(1) Va Adjusment

¤Connect pin 1 of CN209 to (+) jack of D.M.M.

¤ŁAfter turning the VR402(Va ADJ), voltage of D.M.M

adjustment as same as Va voltage which on label of

panel right/top.(Deviation : ±0.5V)

(2) Vs Adjustment

¤Connect pin 8 of CN207 to (+) jack of D.M.M.

¤ŁAfter turning the VR401(Vs ADJ), voltage of D.M.M

adjust as same as Vs voltage which indicated on label

of panel right/top.(Deviation : ±0.5V)

(3) -Vy Adjustment

¤Connect pin 5 of CN208 to (+) jack of D.M.M.

¤ŁAfter turning the VR403(-Vy ADJ), voltage of D.M.M

adjust as same as -Vy voltage which indicated on label

of panel right/top.(Deviation : ±0.5V)

(4) Vsetup Adjustment

¤Connect pin 1 of CN208 to (+) jack of D.M.M.

¤ŁAfter turning the VR404(Vsetup ADJ), voltage of D.M.M

adjust as same as Vsetup voltage which indicated on

label of panel right/top.(Deviation : ±0.5V)

[Refer to Typical Voltage

1. Va : 30 ~ 50V

2. Vs : 170 ~ 185V

3. -Vy : -60 ~ -90V

4. Vsetup : 210 ~ 240V

[Replace PDP Module or Power Board, adjust certainly Power

PCB Assy Voltage.

4. Adjustment of AUTO RGB

4-1. Outline

AUTO RGB adjustment is the function to set the optimum

black-level and Gain automatically in Analog --> Digital

converter and to correct RGB deviation.

4-2. Required Equipment

PC Pattern Generator

(It can be possible to output 16Gray Scale Pattern and RGB

output level is corrected to 0.7±0.1Vp-p)

4-3. Adjustment Method

(1) It can be possible to RGB input 16Gray Scale Pattern

signal of PC Mode and select RGB.

(2) Press the ADJ Key on R/C to enter adjustment mode and

select 2.W/B and then press the VOL + Key.

(3) Turn the HEATRUN OFF and select AUTO RGB and then

press the VOL + Key.

5. Adjustment of White Balance

5-1. Required Equipment

(1) Color analyzer(CA-100 or same production)

(2) Auto Regulator(Required while auto adjustment, and

possible to communicate with RS-232C)

(3) AV Pattern Generator

5-2. Connection Diagram of Equipment for

Measuring

[After stop the Micom by pressing IN-START Key on Remote

Control, insert the P102 with automatic adjustment of

connector.

After remove connector, move the Micom by pressing ENTER

Key.

- 11 -

<Fig 1> Connection Diagram of SONY Power Adj. for

Measuring

COLOR

ANALYZER

TYPE; CA-100

CVBS Signal Input

PDP MONITOR

85IRE Full White

85IRE



Full White

MSPG-2100 or

MSTG-5200

<Fig 2> Connection Diagram of Automatic Adjustment

- 12 -

5-3. Adjustment of White Balance

¥ Operate the Zero-calibration of the CAÑ100, then stick

sensor to PDP module surface when you adjust.

¥ For manual adjustment, it is also possible by the following

sequence.

(1) Select WHITE PATTERN of HEAT RUN mode by pressing

ADJ button on Remote Control for adjustment then operate

HEAT RUN more than 15 minute.

(2) Supply Full White signal(signal output level : 85IRE) in AV

Pattern Generator.

(3) Select image regulation status to ÔClear ImageÕ.

(4) Stick sensor to the center of screen and press the ADJ Key

on R/C to select W/B and then press the VOL + Key to

enter the adjustment mode.

After selecting R ADJ and B ADJ, press the VOL +/- Key

and adjust it until color coordination becomes(B GAIN

fixation)

color coordination : X=0.280±0.003, Y=0.290±0.003

color temperature : 10,000cK ± 500cK

(5) Exit adjustment mode using Enter button.

- 13 -

BLOCK DIAGRAM

1. MODULE of <a> part and PLATE A/V unite two things.

2. Unite after put on BACK COVER INNER of <b> part .

3. Disassembly is opposite to Assembly.

NOTE> Working sequence of <a> Part is different from <b> Part.

- 14 -

ASSEMBLY METHOD

MEMO

- 15 -

- 16 -

EXPLODED VIEW

200

203

201

202

205

204

207

208

209

206

540

401

550

310

551

520

560

570

400

410

530

580

210

301

302

300

305

- 17 -

EXPLODED VIEW PARTS LIST

200 6348Q-E034A PDP,42 16:9 852*480 LOW VOLTAGE DRIVING, FOR DOMESTIC

201 6871QTH025A PWB(PCB) ASSEMBLY,DISPLAY ZCNT ASSY HAND INSERT 42SD4

202 6871QZH023A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42SD4

203 6871QTH026A PWB(PCB) ASSEMBLY,DISPLAY ZCNT ASSY HAND INSERT 42SD4

204 6871QRH021A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42SD4

205 6871QLH021A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42SD4

206 6871QYH022A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42SD4

207 6871QDH061A PWB(PCB) ASSEMBLY,DISPLAY DRV ASSY HAND INSERT 42SD4

208 6871QDH060A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42SD4

209 6871QCH024A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY CTRL B/D (4011/4021)

210 4980V00460A SUPPORTER,VERTICAL MN-42PZ40 .

300 3091V00B01C CABINET ASSEMBLY,MU-42PZ41 3090V00347A LG NO .

3091V00B01J CABINET ASSEMBLY,MZ-42PZ43S NON - SILVER

301 4980V00457A SUPPORTER,FILTER NON MN-42PZ40

302 4980V00458A SUPPORTER,FILTER NON MN-42PZ40

305 3790V00281D WINDOW,1142G02D MN42PZ10 ETCHING MESH 3790V00218C CHANGE

310 5020V00667A BUTTON,CONTROL MN-42PZ40 NON NON NON

400 3809V00A47A BACK COVER ASSEMBLY,MN-42PZ40 NON INNER

401 3301V00010D PLATE ASSEMBLY,A/V 3300V00205A MZ-42PZ43

3301V00010E PLATE ASSEMBLY,A/V 3300V00205A MT-42PZ43

410 3809V00A58A BACK COVER ASSEMBLY,OUTER NON MN-42PZ40

520 6871VMMD03A PWB(PCB) ASSEMBLY,MAIN RF-02RA SAGE2 MT-42PZ41

6871VMMD04A PWB(PCB) ASSEMBLY,MAIN RF-02RA SAGE2 MZ-42PZ43

530 6871VSMD84A PWB(PCB) ASSEMBLY,SUB A/V RF02RA SAGE2

540 6871VSMD92A PWB(PCB) ASSEMBLY,SUB CONT RF02RA MU-42PZ41

550 6871VSMD94A PWB(PCB) ASSEMBLY,SUB PSW RF02RA MU-42PZ41

551 5020V00666A BUTTON,POWER MN-42PZ40 SET

560 6871VSMD93A PWB(PCB) ASSEMBLY,SUB SPK RF02RA MU-42PZ41

570 3501V00115A BOARD ASSEMBLY,POWER BOARD MJ42PZ40 NF01DC SONY 40/42 PDP

580 6871VSMD85A PWB(PCB) ASSEMBLY,SUB INTER RF02RA SAGE2 FIX BD

No. Part No. Description

- 18 -

REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

IC904

IC905

IC906

IC907

IC106

IC107

Q001

Q002

Q101

Q102

Q103

Q104

Q105

Q106

Q107

Q108

Q109

Q110

Q1101

Q1102

Q1103

Q1104

Q1105

Q1106

Q1107

Q1108

Q1109

Q111

Q112

Q201

Q202

Q203

Q204

Q205

Q206

Q301

Q302

Q303

Q413

Q414

Q415

Q601

Q602

Q603

D011

D100

D101

D102

D103

0IAL241610A

0IPH740400G

0IPH743200A

0TR830009BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR104009AF

0TR387500AA

0TR102009AG

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0DD226239AA

IC,AT24C16N-10SI 8P SOIC ST EEPROM

IC,74HC04D HEX INVERTER 14P,SOP TP .

IC,74HC32D 14SOP TP QUAD 2-INPUT OR

TR,BSS83 TP PHILIPS NON N-CHANNEL S/W

TR,CHIP 2SC3875S(ALY) KEC

TR,CHIP 2SA1504S(ASY) KEC

TR,CHIP 2SC3875S(ALY) KEC

TR,CHIP 2SA1504S(ASY) KEC

TR,CHIP 2SC3875S(ALY) KEC

TR,BIPOLARSCHIP KRC104S SOT-23 TP KEC -

TR,CHIP 2SC3875S(ALY) KEC

TR,BIPOLARSCHIP KRC102S KEC TP SOT-23

TR,CHIP 2SC3875S(ALY) KEC

TR,CHIP 2SA1504S(ASY) KEC

TR,CHIP 2SC3875S(ALY) KEC

TR,CHIP 2SA1504S(ASY) KEC

DIODE,SWITCHING CHIP KDS226 SOT-23

DIODE,SWITCHINGCHIP KDS226 SOT-23

LOCA. NO PART NO DESCRIPTION

IC001

IC002

IC101

IC102

IC103

IC104

IC105

IC108

IC1101

IC1102

IC1700

IC1701

IC1801

IC1802

IC1803

IC1804

IC1805

IC1806

IC1807

IC1809

IC1810

IC201

IC202

IC203

IC204

IC205

IC206

IC301

IC302

IC303

IC304

IC402

IC501

IC502

IC601

IC602

IC603

IC604

IC700

IC701

IC801

IC802

IC803

IC804

IC805

IC806

IC807

IC901

IC902

IC903

0ISO208900A

0IMCRFA010A

0IBB368200A

0IAL242110A

0IFA741230A

0IAL242110A

0IPH740800M

0IKE704200J

0IMCRSO008A

0IMCRAD002A

0IMCRG2004B

0ISS464323A

0IMCRRH001A

0IPRPML001A

0IMCRSJ001A

0IMCRSH001A

0IMCRRH001A

0IDS232000A

0IMCRS5003A

0IMCRTI021A

0ISA715100D

0IIT323000E

0IKE704200J

0IMCRTI001A

0IS5160000A

0IMCRGN001A

0IMMRHY033A

0IMCRMN014A

0IKE704200J

0IKE780800J

0ISH052100C

0IMCRG2004B

0ISS464323A

0IPRPML001A

0IMCRRH001A

0ISA428200A

0IMCRFA010A

0ISH122100A

0IPRPML001A

0IMCRFA010A

0IPH743200A

0ICTMMI038A

0IMMRMR009A

0IKE704200J

IC,CXA2089Q 48QFP BK A/V SWITCH

IC,KA7809R, FAIRCHILD 2P D-PAK, R/TP

IC,OPA3682E 16P SOP ST BUFFER AMP

IC,AT24C21-10SI-2.5 8P,SOP TP 1K EEPROM

IC,DM74LS123MX 16SOP TP DUAL RETRIG.

IC,AT24C21-10SI-2.5 8P,SOP TP 1K EEPROM

IC,74F08D 14P SOIC R/TP QUAD 2-INPUT AND

IC,KIA7042AF SOT-89 TP 4.2V DETECTOR

IC,CXA2151Q SONY 48P QFP TRAY 60LCD

IC,AD9883A 80P TQFP R/TP CONVERTER

IC,JAGASM A4 SAGE 352BALL FLEXIBLE

IC,86P-TSOP(II) TRAY 2M*32BIT,64SDRAM

IC,BA033FP ROHM 3P-SOP,TO252-3 R/TP 3.3V

IC,R/TP LDO TYPE 2.5V REGULATOR

IC,SC1565IST-1.8 3P SOT223 TP REGULATOR

IC,PQ05DZ1U SHARP 5, SMD TYPE R/TP

IC,PQ05DZ1U 5, SMD TYPE R/TP REGULATOR

IC,BA033FP ROHM 3P-SOP,TO252-3 R/TP 3.3V

IC,DS232AS 16P,SOP TP RS-232

IC,SIL169 CL100 100P LQFP TRAY TMDS RX

IC,20P TSSOP R/TP BUFFERS/DRIVERS WTH 3

IC,LA7151M 10SOP R/TP AUDIO SW FD-60X3R

IC,VPC3230D C5 80P QFP PROCESSOR PDP50

IC,SOT-89 TP 4.2V VOLTAGE DETECTOR

IC,SN74HCT157D 16P R/TP RL-JA10

IC,SII160 100 TQFP ST DIGITAL TRANSMITTER

IC,S2310 GENESIS 208P PQFP CONVERTER

IC,86P TSOP TRAY 64M FLASH MEMORY

IC,MSP3440G QA B8 V3 80 QFP SOUND IC

IC,KIA7042AF SOT-89 TP 4.2V DETECTOR

IC,KIA7808API 3 ST REGULATOR .

IC,PQ05RD21 4SIP ST REGULATOR

IC,A4 SAGE 352BALL TRAY HIGHLY FLEXIBLE

IC,86P-TSOP(II) TRAY 2M*32BIT,64SDRAM

IC,MIC39100 3P SOT223 R/TP LDO TYPE 2.5V

IC,BA033FP ROHM 3P-SOP,TO252-3 R/TP 3.3V

IC,LA4282 12S 2CHX10W AUDIO AMP

IC,2P D-PAK, R/TP REGULATOR IC

IC,PQ12RF21 4P(TO-220) 12V S/W RE - - - -

IC,MIC39100 3P SOT223 R/TP LDO TYPE 2.5V

IC,KA7809R, FAIRCHILD 2P D-PAK, R/TP

IC,14SOP TP QUAD 2-INPUT OR GATE

IC,00P QFP TRAY SINGLE 16BIT CMOS CHIP

IC,90 4MBIT 48P TSOP ST FLASH MEMORY

IC,SOT-89 TP 4.2V VOLTAGE DETECTOR

IC

TRANSISTOR

DIODE

- 19 -

LOCA. NO PART NO DESCRIPTION

D104

D105

D106

D107

D108

D109

D110

D111

D112

D113

D114

D115

D1801

D1802

D1803

D1804

D1805

D1806

D1809

D1810

D601

D602

D603

D604

D605

D606

D801

D802

D803

D805

D806

LD001

LD401

LD801

LD802

LD803

ZD101

ZD103

ZD104

ZD105

ZD301

ZD302

ZD902

C002

C013

C014

C015

C019

C020

C022

0DD226239AA

0DD184009AA

0DD226239AA

0DD184009AA

0DD226239AA

0DL200000CA

0DL233309AC

0DZRM00178A

0DR050008AA

0DZRM00178A

0CE4763F618

0CE476SF6DC

0CE105SK6DC

DIODE,SWITCHINGCHIP KDS226 SOT-23

DIODE,SWITCHINGKDS184S CHIP 85V 300MA

DIODE,SWITCHINGCHIP KDS226 SOT-23

DIODE,SWITCHINGKDS184S CHIP 85V 300MA

DIODE,SWITCHINGCHIP KDS226 SOT-23

LED,SAM5670(DL-2LRG) BK Y-GREEN -

LED,SAM2333 TP GREEN:10MCD, RED:6MCD

DIODE,R/TP SMD 0.2W 5.1V 5MA -PF

DIODE,TC R/TP SEMTECH SOD323 5V 5A 15A -

DIODE,R/TP SEMTECH SOD323 5V 5A 15A - -

DIODE,1B ROHM R/TP SMD 0.2W 5.1V 5MA -PF

47UF SRE 16V M FL TP5

47UF MVG 16V M SMD R/TP

1UF MVG 50V M SMD R/TP

LOCA. NO PART NO DESCRIPTION

C023

C025

C026

C030

C031

C034

C035

C038

C042

C043

C044

C045

C1110

C1119

C1131

C1132

C1133

C1135

C1147

C1148

C1149

C115

C1154

C116

C1160

C1165

C117

C118

C129

C132

C134

C135

C136

C137

C138

C139

C140

C141

C145

C147

C149

C1792

C1807

C1809

C1812

C1815

C1818

C1821

C1823

C1825

C1839

C1841

0CE105SK6DC

0CE476SF6DC

0CE105SK6DC

0CE476SF6DC

0CH3104K566

0CE476SF6DC

0CE105VK6DC

0CE107VF6DC

0CE106SF6DC

0CE226VF6DC

0CE106SF6DC

0CE476SF6DC

0CE226VF6DC

0CE476SF6DC

0CK823DK56A

0CE226VF6DC

0CE476SF6DC

0CE105CK636

0CE106SF6DC

0CE476SF6DC

0CE107VF6DC

0CE477WF6DC

0CE227WF6DC

0CE476SF6DC

0CE477WF6DC

0CE107VF6DC

0CE476SF6DC

0CE477WF6DC

0CE476SF6DC

0CE477WF6DC

1UF MVG 50V M SMD R/TP

47UF MVG 16V M SMD R/TP

1UF MVG 50V M SMD R/TP

47UF MVG 16V M SMD R/TP

0.1UF 50V 10% X7R 2012 R/TP

47UF MVG 16V M SMD R/TP

1UF MV 50V 20% R/TP(SMD) SMD

100UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

22UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

AL.ELECTROLYTIC47UF MVG 16V M SMD R/TP

22UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

82000PF 2012 50V 10% R/TP X7R

22UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

1UF SHL,SD 50V M FM5 BP(D) TP

10UF MVG 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

100UF MV 16V 20% R/TP(SMD) SMD

470UF MVK 16V 20% SMD R/TP(SMD)

220UF MVK 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

470UF MVK 16V 20% SMD R/TP(SMD)

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

470UF MVK 16V 20% SMD R/TP(SMD)

47UF MVG 16V M SMD R/TP

470UF MVK 16V 20% SMD R/TP(SMD)

CAPACITOR

For Capacitor & Resistors,

the charactors at 2nd and 3rd

digit in the P/No. means as

follows;

CC, CX, CK, CN : Ceramic

CQ : Polyestor

CE : Electrolytic

RD : Carbon Film

RS : Metal Oxide Film

RN : Metal Film

RF : Fusible

- 20 -

LOCA. NO PART NO DESCRIPTION

C1844

C1847

C1849

C1852

C1855

C1858

C1860

C1862

C1865

C1868

C1871

C1874

C1877

C1880

C1882

C1884

C1887

C1890

C1893

C1898

C1900

C214

C223

C224

C225

C301

C302

C303

C304

C307

C322

C333

C334

C335

C338

C352

C356

C360

C437

C527

C532

C601

C602

C604

C605

C606

C607

C608

C609

C610

C611

C612

0CE107VF6DC

0CE476SF6DC

0CE477WF6DC

0CE107VF6DC

0CE476SF6DC

0CE477WF6DC

0CE107VF6DC

0CE476SF6DC

0CE477WF6DC

0CE227WF6DC

0CE476SF6DC

0CE107VF6DC

0CE476SF6DC

0CE106SF6DC

0CE107VF6DC

0CE106SF6DC

0CK224DF56A

0CE106SF6DC

0CK224DF56A

0CE107VF6DC

0CE476SF6DC

0CE107VF6DC

0CE477DK618

0CE227WF6DC

0CE105VK6DC

0CE107DH618

0CE106SF6DC

0CE107DH618

0CE106SF6DC

0CE107DH618

0CE106SF6DC

0CQ1041N509

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

470UF MVK 16V 20% SMD R/TP(SMD)

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

470UF MVK 16V 20% SMD R/TP(SMD)

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

470UF MVK 16V 20% SMD R/TP(SMD)

220UF MVK 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

220000PF 2012 16V 10% R/TP X7R

10UF MVG 16V 20% R/TP(SMD) SMD

220000PF 2012 16V 10% R/TP X7R

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

100UF MV 16V 20% R/TP(SMD) SMD

470UF STD 50V 20% FL TP 5

220UF MVK 16V 20% R/TP(SMD) SMD

1UF MV 50V 20% R/TP(SMD) SMD

100UF STD 25V M FL TP5

10UF MVG 16V 20% R/TP(SMD) SMD

100UF STD 25V M FL TP5

10UF MVG 16V 20% R/TP(SMD) SMD

100UF STD 25V M FL TP5

10UF MVG 16V 20% R/TP(SMD) SMD

0.1U 100V K POLY TP

LOCA. NO PART NO DESCRIPTION

C613

C614

C615

C616

C618

C621

C624

C625

C627

C628

C629

C630

C631

C633

C634

C635

C637

C647

C648

C650

C652

C653

C671

C672

C673

C674

C675

C676

C792

C801

C806

C807

C809

C813

C814

C817

C820

C821

C824

C825

C827

C829

C832

C835

C837

C839

C842

C845

C847

C849

C852

C855

0CQ1231N419

0CQ1041N509

0CE227WF6DC

0CE107VF6DC

0CE106SF6DC

0CE335SK6DC

0CE474SK6DC

0CE106SF6DC

0CE107VF6DC

0CE476SF6DC

0CE106SF6DC

0CE474SK6DC

0CE477DK618

181-120K

0CE227WF6DC

0CE477WF6DC

0CE105VK6DC

0CE227WF6DC

0CE477WF6DC

0CE227WF6DC

0CE477WF6DC

0CE476SF6DC

0CE107VF6DC

0CE476SF6DC

0CE107VF6DC

0CE476SF6DC

0.0120UF 100V J PE NI TP

0.1U 100V K POLY TP

220UF MVK 16V 20% R/TP(SMD) SMD

100UF MV 16V 20% R/TP(SMD) SMD

10UF MVG 16V 20% R/TP(SMD) SMD

3.3UF MVG 50V 20% SMD R/TP

0.47UF MVG 50V M SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

10UF MVG 16V 20% R/TP(SMD) SMD

0.47UF MVG 50V M SMD R/TP

470UF STD 50V 20% FL TP 5

2200PF 4KV M E FMTW LEAD 4.5

220UF MVK 16V 20% R/TP(SMD) SMD

470UF MVK 16V 20% SMD R/TP(SMD)

1UF MV 50V 20% R/TP(SMD) SMD

220UF MVK 16V 20% R/TP(SMD) SMD

470UF MVK 16V 20% SMD R/TP(SMD)

220UF MVK 16V 20% R/TP(SMD) SMD

470UF MVK 16V 20% SMD R/TP(SMD)

47UF MVG 16V M SMD R/TP

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

100UF MV 16V 20% R/TP(SMD) SMD

47UF MVG 16V M SMD R/TP

For Capacitor & Resistors,

the charactors at 2nd and 3rd

digit in the P/No. means as

follows;

CC, CX, CK, CN : Ceramic

CQ : Polyestor

CE : Electrolytic

RD : Carbon Film

RS : Metal Oxide Film

RN : Metal Film

RF : Fusible

LG MT-42PZ40/V/B/R/S User manual

Popular Monitor manuals by other brands