LG 50PA4500 User manual

User Guide
This is a 「User Guide」 installed on the TV.
The contents of this guide are subject to change without prior notice for quality
improvement.

GP2

 
 
 

 
 

 




GP2
eng
❐Automatically Setting Up Programme
SETTINGS ➾ SETUP ➙Auto Tuning
Automatically tunes the programmes.
1 Select Country where the TV is used. Programme settings change depending
on the country you choose.
2 Initiate Auto Tuning.
3 Select Input Source of your choice.
4 Set Auto Tuning following screen instructions.
✎If Input Source is not connected properly, programme registration may not
work.
✎Auto Tuning only finds programmes that are currently broadcasting.
✎If Lock System is turned on, a pop-up window will appear asking for
password.

GP2
eng
❓Cable DTV Setting option
When searching for programmes using FULL setting it can take a long time. The
following values are needed in order to search all available programmes quickly
and correctly. The commonly used values are provided as “default”.
• Frequency : Enter a user-defined frequency.
• Symbol rate : Enter a user-defined symbol rate (Symbol rate: Speed at which
a device such as modem sends symbols to a programme).
• Modulation : Enter a user-defined modulation. (Modulation: Loading of audio
or video signals onto carrier).
• Network ID : Unique identifier allocated for each user.
• Start Frequency : Enter a user-defined start frequency range.
• End Frequency : Enter a user-defined end frequency range.

GP2
eng
❐Cable DTV Setting
SETTINGS ➾ SETUP ➙ Cable DTV Setting
[In Cable mode only]
When Channel Auto Update is On, you can update information for all the
programmes that can be updated, including the programme currently being
watched. When Channel Auto Update is Off, you can only update information for
the programme currently being watched.
✎The range that a user can select from the Service Operator menu differs
depending on number of Service Operator supported by each country.
✎If number of supported Service Operator for each country is 1, corresponding
function becomes inactive.
✎You can not select the Cable DTV Setting when the service operator is set to
“Ziggo”.

GP2
eng
❐To use Manual Tuning
SETTINGS ➾ SETUP ➙ Manual Tuning
Adjusts programmes manually and saves the results.
For digital broadcasting, signal strength and signal quality can be checked.
For analogue broadcasting, you can set up station names and use fine tuning.
Normally fine tuning is only necessary if reception is poor.

GP2
eng
❐To edit programmes
SETTINGS ➾ SETUP ➙ Programme Edit
Edits the saved programmes.
Set as favourite programme, block/unblock programme, skip programme etc. of
the selected programme.

GP2
eng
Press TEXT button.
[depending on the country]
Teletext is a free service provided by the TV station that offers text-based
information about TV programmes, news and weather.
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT
systems.
• Colour button: To select the preceding or following page.
• Number button: Enters the desired page number.
• ꔵ: To select the preceding or following page.

GP2
eng
❐Special Teletext Function
Press T. OPT button.
Select the Text Option menu.
• ꔻIndex : Select each index page.
• ꔾTime : When viewing a TV programme, select this menu to display the
time at the top right hand corner of the screen.
• ꕀHold : Stops the automatic page change which will occur if a teletext
page consists of 2 or more sub pages.

GP2
eng
• ꔽReveal : Select this menu to display concealed information, such as
solutions to riddles or puzzles.
• ꔼUpdate : Displays the TV picture on the screen while waiting for a new
teletext page.
• Language [In Digital Mode Only] : Sets Teletext language.

GP2
eng
Press the TEXT button.
[In UK/Ireland only]
The TV gives you access to digital teletext which gives much better text,graphics
etc. than older analogue teletext. This digital teletext can access special digital
teletext services and speci󷷆c services which broadcast digital teletext.

GP2
eng
❓Teletext within digital service
1 Press the numeric or ꔵbutton to select a certain service which
broadcasts digital teletext.
2 Follow the indications on digital teletext and move onto the next step by
pressing TEXT, OK, Navigation, Red, Green, Yellow, Blue or NUMBER buttons
etc..
3 Press the number or ꔵ button to use a di󷷅erent digital teletext service.

GP2
eng
❓Teletext in digital service
1 Press the numeric or ꔵbutton to select a certain service which
broadcasts digital teletext.
2 Press the TEXT or colour button to switch on teletext.
3 Follow the indications on digital teletext and move onto the next step by
pressing OK, Navigation, Red, Green, Yellow, Blue or NUMBER buttons etc..
4 Press the TEXT or colour button to switch o󷷅 digital teletext and return to TV
viewing.

GP2
eng
SETTINGS ➾ OPTION ➙ Data Service
[Depending on country]
This function allows users to choose between MHEG (Digital Teletext) and Teletext
if both exist at the same time.
If only one of them exists, either MHEG or Teletext is enabled regardless of
which option you selected.

GP2
eng
SETTINGS ➾ SETUP ➙ CI Information
• This function enables you to watch some encrypted services (pay
services).
• If you remove the CI Module, you cannot watch pay services.
• CI (Common Interface) functions may not be possible depending upon the
country broadcasting circumstances.
• When the module is inserted into the CI slot, you can access the module
menu.
• To purchase a module and smart card, contact your dealer.

GP2
eng
• When the TV is turned on after inserting a CI Module, you may not have any
sound output. The Smart Card may not be compatible with the CI module.
• When using a CAM(Conditional Access Module), please make sure it
meets fully the requirements of either DVB-CI or CI plus.
• An abnormal process of CAM(Conditional Access Module) may cause a bad
picture.

GP2
eng
SETTINGS ➾ PICTURE ➙ Aspect Ratio
Selects the screen aspect ratio.
• 16:9: Resizes images to fit the screen width.
• Just Scan: Displays video images in the original size without removing parts
of the edge of the image.
✎In DTV, Component, HDMI, and DVI (over 720p) mode, Just Scan is
available.
• Original: When your TV receives a wide screen signal it will automatically
change to the picture format broadcasted.

GP2
eng
• Full Wide: When TV receives the wide screen signal, it will let you adjust
the picture horizontally or vertically, in a linear proportion,to fill the entire
screen fully. 4:3 and 14:9 video is supported in full screen without any video
distortion through DTV input.
✎In Analogue/DTV/AV/Scart mode, Full Wide is available.
• 4:3: Resizes images to the previous standard 4:3.
• 14:9: You can view a picture format of 14:9 or a general TV programme in the
14:9 mode. The 14:9 screen is viewed in the same way as in 4:3, but is moved
up or down.
• Zoom: Resizes images to fit the screen width. The top and bottom parts of the
image may be cut off.

GP2
eng
• Cinema Zoom: Choose Cinema Zoom when you want to enlarge the picture in
correct proportion.
✎While viewing an external device, these cases may result in image burn:
- a video with stationary caption (such as network name)
- 4 : 3 aspect ratio mode for an extended period
Take caution when using these functions.
✎Available picture size may differ depending on the input signal.
✎The screen aspect ratios on HDMI/RGB-PC input are available in 4:3 and 16:9
only. (Only for models supporting PC connection)

GP2
eng
❐To adjust picture in PC input mode
SETTINGS ➾ PICTURE ➙ Screen
Adjusts picture in RGB-PC mode.
• Auto Config.:Optimizes picture.
• Position / Size / Phase:If screen size or location is distorted, user can directly
adjust the screen size and position.
• Reset:Resets all changes on picture settings on PC input mode.