LG LRESO25ST User manual

Life’s Good
aes
A pe YN A Ae /,
ALLATION MANUAI
a Oram # % & 1O o Como
ELECTRIC RANGE
Please read these instructions thoroughly before
installing and operating the range.
LRESO25ST LRESO235ST
LRESO25SB LRESO235B
LRESO2Z25SW LRESO2Z3SW
Ml | Printed on 100% Recycled Paper
MFL57205804
www.lg.com

ce TABLE OF CONTENTS
TABLE OF CONTENTS
3 SAFETY
Ww Before You Begin
Ww Important Safety Instructions
oO Prepare to Install the Range
PREPARE TO INSTALL RANGE
an
|
aA
Installation Drawings
wel ELECTRICAL CONNECTIONS
Electrical Connection Requirements
Connect Range Cord
3-Wire Connection With a Power Supply Cord
4-Wire Connection With a Power Supply Cord
3-Wire Connection: Conduit
4-Wire Connection: Conduit O
0
0
MO
NAN
WN
17 INSTALL THE RANGE
11. Anti-Tip Device Installation
11. Final Installation

SAFETY 3
BEFORE YOU BEGIN
Remove all tape and packing materials before using the range.
Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials.
You can download the installation and owner’s manual at: http://www.lg.com.
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all instructions before using your oven to prevent the risk of fire, electric shock, personal injury, or
damage when using the range. This guide does not cover all possible conditions that may occur. For further assistance
contact your service agent or manufacturer.
you and others. All safety messages will follow the safety alert symbol with either the word “WARNING” or
' This is the safety alert symbol. This symbol alerts you to potential hazards that can cause personal injury to
“CAUTION.”
4. WARNING
This symbol will alert you to hazards or unsafe practices which could cause serious bodily harm or death.
J\CAUTION
This symbol will alert you to hazards or unsafe practices which could cause bodily injury or property damage.
- 4. WARNING
¢ The information in this manual should be followed exactly.
- A fire or electrical shock may result causing property damage, personal injury or death.
« Do not step or sit on the oven door. Install the Anti-Tip Brackets supplied with the range.
- The range could be tipped and injury might result from spilled hot liquid, food, or the range itself.
- If the range is pulled away from the wall for cleaning, service, or any other reason, ensure that the Anti-Tip de-
vice is properly reengaged when the range is pushed back against the wall.
- Install the Anti-Tip Brackets.
- Achild or adult can be killed when the range is tipped.
- 1) According to the Anti-Tip Bracket Template, install 2 Anti-Tip Brackets to the floor and wall.
- Anti-Tips will fasten the range by holding the range’s 2 legs of the rear side and the Anti-Tip Bracket Template
lets you know proper locations of Anti-Tip Brackets easily.
- 2) Engage the range to the Anti-Tip Brackets by putting the range’s 2 legs into each Anti-Tip Bracket.
- 3) Re-engage the Anti-Tip Brackets if you can move the range except for range’s front direction.
- 4) See installation instructions for details (refer to the page 11).
- Failure to do so can result in death or serious burns to children or adults.
You should use two or more people to move and install range. (Excessive Weight Hazard)
- Failure to do so can result in back or other injury.
You never pull or push any handles of door to move and install range.
- Failure to do so can result in serious damage to the door of the range.
New branch-circuit installations (1996 NEC) for mobile homes, recreational vehicles, and installations
where local codes do not allow grounding through the neutral wire require a 4-conductor UL listed range
cord or 4 wire conduit connection.
e e e

4 SAFETY
7 4. WARNING
« Power supply cord and plug should not be modified. If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
Using an extension cord to connect the power is prohibited. The way to connect the power cord and plug
directly is strongly recommended.
Electrical ground is required on this appliance.
You should make sure that the power cord is not pinched by the range or heavy objects.
- Failure to do so can result in serious burns or electrical shock.
You never remove the protection cover covering the rear of oven.
- Failure to do so can result in serious damage to power cord. The damage causes serious burns and electric
shock.
The middie (neutral or ground) wire of a 3 wire power cord or a 3 wire conduit has to be connected to the
middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be
connected to the outside posts of the main terminal connection block.
- Failure to do so can result in electrical shock, severe personal injury or death.
Only a 4-conductor power-supply cord kit rated 120/240 volts, 50 amperes and marked for use with
ranges with closed-loop connectors or open-end spade lugs with upturned ends shall be used. The
middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of
the main terminal block. The other two wires of the power cord or conduit have to be connected to the
outside posts of the main terminal connection block. The 4th ground wire must be connected to the
frame of the range with the ground screw.
- Failure to do so can result in electrical shock, severe personal injury or death.
e e e e e e
J.CAUTION
« You should put on gloves during the installation procedure.
- Failure to do so can result in bodily injury.
« You should make sure that the wall covering, countertop and cabinets around the range can withstand
the heat (up to 194°F) generated by the range.
- Discoloration, delamination or melting may occur.
- This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194°F.
« Cabinet storage space located above the surface units should be avoided.
¢ You should install a range hood that projects horizontally a minimum of 5 inches beyond the bottom of
the cabinets. If cabinet Storage is to be provided.
- The risk of burns or fire by reaching over the heated surface elements can be reduced.
« You should not install the range in the humid place. Splashing the range with water or any electrolyte can
result in electrical shock.
¢ You should not let cooking grease or flammable material accumulate in or near the range.
- Failure to do so can result in serious burns.

SAFETY 5
4 WARNING
° The information in this manual should be
followed exactly.
- A fire or electrical shock may result causing
property damage, personal injury or death.
74. WARNING
e Any person should not step or
sit on the oven door. You should
LK install the Anti-Tip Brackets
aS ¢ ¢,
supplied with the range.
- The range could be tipped and
injury might result from spilled hot
liquid, food, or the range itself.
oe - Ifthe range is pulled away from the
wall for cleaning, service, or any
other reason, ensure that the Anti-
Tip Device is properly reengaged
when the range is pushed back
against the wall. Broiling beyond
recommended cooking times.
-~\CAUTION
« You should put on gloves during the installation
procedure.
- Failure to do so can result in bodily injury.
f PARTS PROVIDED
—-@ NOTE
+ Read all instructions contained in these installation
instructions before installing range.
« Remove all packing materials from the oven
compartments before connecting the electrical
supply to the range.
« Observe all governing codes and ordinances.
+ Be sure to leave these instructions with the
consumer.
@ NOTE
Keep these instructions with your owner's manual for
future reference.
» As when using any appliance generating heat, there
are certain safety precautions you should follow.
» Be sure your range is installed and grounded properly
by a qualified installer or service technician.
» Make sure the wall coverings around the range can
withstand the heat generated by the range.
* To eliminate the need to reach over the surface
elements, cabinet storage space above the elements
should be avoided.
PREPARE TO INSTALL THE RANGE
TOOLS NEEDED
(es
Phillips Screwdriver
Co3a—$—
Flat-blade
Screwdriver
va Nut D river
Tape Measure
—— a
Pencil Gloves
Template (1)
RoLECg
Anchor Sleeves (1
Anti-Tip Brackets (2)
WY
Lag Bolts (12)
(For Anti-Tip Bracket Mounted
on Concrete Floors and Walls)
PARTS NOT PROVIDED
(UL Approved 40 or 50 AMP) Strain Relief
(For Conduit
Installations Only) 4-Wire Cord OR 3-Wire Cord

6 PREPARE TO INSTALL THE RANGE
INSTALLATION DRAWINGS
® NOTE
"save FORTHE USE OF THE LOCAL ELECTRICAL INSPECTOR
CLEARANCES AND DIMENSIONS (Figure 1)
To install range refer to the following Figure 1.
For installation in CANADA, a Free-standing range is not to be installed closer than 15/32 (12mm) from any adjacent
surface.
“CAUTION ——
e Make sure that the wall covering, countertop
and cabinets around the range can with-
stand the heat (up to 194°F) generated by
the range.
- Discoloration, delamination or melting may
occur.
- This range has been designed to comply with
the maximum allowable wood cabinet tem-
peratures of 194°F,
3” (7.6cm) 24"
(60.9cm)
3" (7,.6cm)
| a5" Ay
' ormal
~™ (63.5em) counter
Acceptable
electrical
top depth
outlet
area
<=
Counter
15.2em a
(91.4em) top height
LL)
36” 1, |
(91.4cm) | Kv
30"
(762m)
A= 30 (76.2 cm) For U.S.A
= 30 (76.2 cm) ~ 31 (78.7 cm) For CANADA
FIgURE 1
“CAUTION —
e Cabinet storage space located above the
surface units should be avoided.
« Install a range hood that projects horizontally
a minimum of 5 inches beyond the bottom
of the cabinets if cabinet storage is to be
provided.
- The risk of burns or fire by reaching over the
heated surface elements can be reduced.
5
| 0
(76.2crn)
*30" (76.2cm)}
Minimum |
OQ
Oo
FIgURE 2
MINIMUM DIMENSIONS (Figure 2)
* 30" (76.2 cm) minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or
metal cabinet; or 24" (60.9 cm) minimum when bottom of wood or metal cabinet is protected by not less than 1/4"(6.4
cm) flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" (0.381 mm) stainless steel,
0.024" (0.610 mm) aluminum or 0.020" (0.508 mm) copper.
** 15" (38.1 cm) minimum between countertop and adjacent cabinet bottom.

ELECTRICAL CONNECTIONS 7
ELECTRICAL CONNECTION
REQUIREMENTS
This appliance must be installed and grounded ona
branch circuit by a qualified technician in accordance
with the National Electrical code ANSI/NFPA NO. 70 -
latest edition.
All wiring should conform to Local and NEC. This range
requires a single-phase, 3 wire, A.C 120/208V or 120/240V
60Hz electrical system. Use only a 3-conductor ora
4-conductor UL-listed range cord with closed-loop
terminals, open-end spade lugs with upturned ends
or similar termination. DO NOT install the power cord
without a strain relief.
A range cord rated at 40 amps with 120/240 minimum
volt range is required. If a 50 amp range cord is used, it
should be marked for use with 138” diameter connection
openings. This appliance may be connected by means
of conduit or power cord. If conduit is being used, go to
page 7 for 3 wire conduit connections or page 8 for 4
wire conduit connections.
4, WARNING
« New branch-circuit installations (1996 NEC)
for mobile homes, recreational vehicles, and
installations where local codes do not allow
grounding through the neutral wire require
a 4-conductor UL listed range cord or 4 wire
conduit connection.
« Power supply cord and plug should not be
modified. if it will not fit the outlet, have a
proper outlet Installed by a qualified electrician.
« Using an extension cord to connect the power is
prohibited. The way to connect the power cord
and plug directly is strongly recommended.
« Electrical ground is required on this appliance.
« You should make sure that the power cord is
not pinched by the range or heavy objects.
- Failure to do so can result in serious burns or
electrical shock.
Specified power-supply-cord kit rating
Range rating, watts Specified Diameter (inches) of Range
rating of power connection Opening
120/240 volts | 120/208 volts | supply-cord kit,| Power cord Conduit
3-wire 3-wire amperes
8,750- 16,500 | 7,801- 12,500 | 40 or50A 13/3” 11/3"
16,501 - 22,500) 12,501 - 18,500 50 13/4" 13/3”
3, 4- Wire electrical wall Receptacle
4 Wire receptacle (14-50R) |
| Q 3 Wire receptacle (10-50R) |
Flg URE 3
CONNECT RANGE CORD
The Rear Access cover must be removed. Loosen the
three screws with a screwdriver. The terminal block will
then be accessible.
Cord/Conduit Access
connection cover
Drawer body plate
FIgURE 4
The Cord/Conduit connection plate is used for the
installation of power cord or conduit. For power cord,
install it with the connection plate as INSTALLED. For
conduit, remove the connection plate located below the
rear of the drawer body and use the conduit hole (1 1/3”)
instead of power cord hole (1 3/8”). (Refer to Figure 5 and 6.)
V/s"
ck 8cm)
——== P/s"
P/s"(Cord) — 1'/e" (Conduit) (3.5em)
Remove the Conduit connection plate
FIgURE 5
Cord/conduit
connection
Strain relief
Conduit
Assemble the
strain relief hole
Cord Strain “4
relief ~
Reinstall the Cord/Conduit connection plate
FIgURE 6

8&8 ELECTRICAL CONNECTIONS
3-WIRE CONNECTION WITH
A POWER SUPPLY CORD
4. WARNING
¢ The middle (neutral or ground) wire of a 3
wire power cord or a 3 wire conduit has to
be connected to the middle post of the main
terminal block. The remaining two wires of the
power cord or conduit have to be connected
to the outside posts of the main terminal
connection block.
- Failure to do so can result in electrical shock,
severe personal injury or death.
Install the power cord as follows:
For power cord installations, Hook the strain relief over
the power cord hole (17/s”) located below the rear of
lower oven. Insert the power cord through the strain
relief and tighten it. (Refer to Figure 7.)
DO NOT install the power cord without a strain relief.
1.Remove the lower 3 screws from the terminal block
and retain them. (Refer to Figure 8.)
2. Insert the 3 screws through each power cord terminal
ring and into the lower terminals of the terminal block.
Make sure that the center wire (white/neutral) is
connected to the center lower position of the terminal
block.
3. Tighten 3 screws securely into the terminal block. Do
not remove the ground strap connections.
4, Refer to page 11.
Separate Strain Relief
before installation
Assemble the strain relief SN Power cord
to the 17/." opening in “ss -
‘ ‘
‘. x ?
Conduit connection plate
Fig URE7
3-wire connection
Black White Red
Hy if
Conduit
S=
connection
plate
|
Fig URE 8

ELECTRICAL CONNECTIONS 9
4-WIRE CONNECTION WITH
A POWER SUPPLY CORD
4, WARNING
e Only a 4-conductor power-supply cord kit rated
120/240 volts, 50 amperes and marked for use
with ranges with closed-loop connectors or
open-end spade lugs with upturned ends shall
be used. The middle (neutral) wire of the power
cord or 4-wire conduit has to be connected to
the middle post of the main terminal block.
The other two wires of the power cord or
conduit have to be connected to the outside
posts of the main terminal connection block.
The 4th ground wire must be connected to the
frame of the range with the ground screw.
- Failure to do so can result in electrical shock,
severe personal injury or death.
Install the power cord as follows:
For power cord installations, Hook the strain relief over
the power cord hole (17/s”) located below the rear of
lower oven. Insert the power cord through the strain
relief and tighten it. (Refer to Figure 7.}
DO NOT install the power cord without a strain relief.
1.Remove the lower 3 screws from the terminal block
and retain them. (Refer to Figure 9.)
2.Remove ground strap and discard as show in in
Figure 9,
3. Insert the ground screw into the power cord ground
wire terminal ring and secure it to the range frame.
4, Insert the 3 screws through each power cord terminal ring
and into the lower terminals of the terminal block. Make
sure that the center wire (white/neutral) is connected to
the center lower position of the terminal block.
5. Tighten 3 screws securely into the terminal block.
3-WIRE CONNECTION: CONDUIT
Install the conduit as follows:
Remove the Conduit connection plate from the rear of
lower oven and rotate it as shown in Figure 5. The
conduit hole (1'/s") must be used.
First, prepare the conduit wires as shown in Figure 10.
3 wire
Y" 3/s"
(25cm) — (0.9 cm)
: et
Conduit ~~”
connection
plate
or
FIgURE 10
Second, install conduit as shown in Figure 6.
For conduit installations, after purchasing a strain relief,
insert it in the conduit hole (1'/s”). Then install the
conduit through the body of strain relief and fasten the
strain relief with its ring. Reinstall the bracket.
For conduit connections :
If the wire in the conduit is copper it must be 8 or 10
AWG wiring.
If the wire in the conduit is aluminum it must be 6 or 8
AWG wiring.
1. Loosen the lower 3 screws from the terminal block.
Refer to Figure 11.)
2. Insert the bare wire (white/neutral) end through the
center terminal block opening. Do not remove ground
strap connections.
3. Insert the two side bare wire ends into the lower left
and the lower right terminal block opening. Tighten
the 3 screws securely into the terminal block.
(approximately 35 - 50 IN-LB)
4, Refer to page 11.
4-wire connection
Black White Red
Terminal
E ae block
hag Bey ite Ground
al
ia
strap
Remove ground
strap and discard
Conduit
connection plate
Ground screw
3-wire connection
Black White Red
Terminal
i a block
Wire ends
S¢,
connection plate
Fig URE 9
FIgURE 11

10 ELECTRICAL CONNECTIONS
4-WIRE CONNECTION: CONDUIT
1. Follow the instructions under “Install the conduit as
follows” on page 8 to correctly install the strain relief.
DO NOT install the conduit without a strain relief.
. Loosen the 2 lower left and right screws from the
terminal block. (Refer to Figure 12.) Remove the lower
2 center screws.
. Remove ground strap and discard as shown in Figure
12. Do not discard any screws.
. Attach the ground bare wire end to range frame and
secure it in place with the ground screw (Refer to
figure 12.)
. Insert the bare wire (white/neutral) end through the
center terminal block opening.
. Insert the two side bare wire ends into the left and the
right terminal block opening. Tighten the 3 screws
securely into the terminal block. (approximately
35 - 50 IN-LB)
. Refer to page 11.
4-wire connection
Black White Red
Terminal
block
Ground
strap
Remove
ground
strap and
discard
Conduit
connection plate
/ ©) ono
. Ground
‘
\ Screw
’
FIgURE 12