LG LH-C6230 User manual

DVD/CD/VCR RECEIVER
Home Cinema System
OWNER’S MANUAL
MODEL: LH-C6230
(Main Unit: LH-C6230Y
Speakers: LHS-C6230T, LHS-C6230W)
Before connecting up, operating or repairing this product,
please read this instruction booklet carefully and completely.
CD-R/RW
PAL
LH-C6230Y NA8PLL-ENG
P/N: 3828R-D032X

2
Safety Precautions
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation mark within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the instructions accompanying the
product.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
CAUTION:
This DVD/CD/VCR receiver employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain it for future reference. Should the
unit require maintenance, contact an authorized service loca-
tion (see service procedure).
Performing controls, adjustments, or carrying out procedures
other than those specified herein may result in hazardous radi-
ation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
This product is manufactured to comply with the
radio interference requirements of EEC
DIRECTIVE 89/336/EEC, 93/68/EEC and
73/23/EEC.
OTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed by
Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection tech-
nology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is located on the back
of this unit. This number is unique to this unit and not available
to others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ___________________________________
Serial No. ___________________________________
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

3
INTRODUCTION
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 6
Display Window Indicators . . . . . . . . . . . . . . . . . . . 7
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . 9
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14
TV & Set Top Box Connections . . . . . . . . . . . . . 10
Accessory Audio/Video (A/V) Connections to . . . .
DVD/CD/VCR receiver . . . . . . . . . . . . . . . . . . . . 11
Radio Aerial Connections. . . . . . . . . . . . . . . . . . 11
Speaker System Connection . . . . . . . . . . . . . . . 12
Speaker Positioning . . . . . . . . . . . . . . . . . . . . . . 13
Mini Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Before Operation - VCR part . . . . . . . . . . . . . . 15-19
Video channel Set . . . . . . . . . . . . . . . . . . . . . . . 15
Using your receiver for the very first time . . . . . . 15
How to use the main menu. . . . . . . . . . . . . . . . . 16
Tuning in TV stations Automatically . . . . . . . . . . 16
Tuning in TV stations Manually . . . . . . . . . . . . . . 17
Changing the order of TV stations . . . . . . . . . . . 18
Deleting TV stations . . . . . . . . . . . . . . . . . . . . . . 18
Setting the clock Manually . . . . . . . . . . . . . . . . . 19
To set the colour system . . . . . . . . . . . . . . . . . . 19
Before Operation - DVD part . . . . . . . . . . . . . . 20-23
General Explanation. . . . . . . . . . . . . . . . . . . . . . 20
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 20
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 21-23
General Operation . . . . . . . . . . . . . . . . . . . . 21
Language . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Speaker setup . . . . . . . . . . . . . . . . . . . . . . . 22
Others (DRC/Vocal/PBC/Auto play) . . . . . . . 22
Parental Control. . . . . . . . . . . . . . . . . . . . . . 23
Operation
Operation with Tape . . . . . . . . . . . . . . . . . . . . . 24-27
Playing a tape . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CM (Commercial Message) SKIP. . . . . . . . . 24
OPR (Optimum Picture Response). . . . . . . . 24
Instant Timer Recording (ITR) . . . . . . . . . . . . . . 25
Timer recording using On Screen Display . . . 26-27
Operation with DVD and Video CD . . . . . . . . . . 28-30
Playing a DVD and Video CD . . . . . . . . . . . . . . . 28
General Features . . . . . . . . . . . . . . . . . . . . . . . . 28
Moving to another TITLE . . . . . . . . . . . . . . . 28
Moving to another CHAPTER/TRACK . . . . . 28
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Still Picture and Frame-by-Frame Playback . 29
Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 29
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 29
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 29
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 29
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Marker Search. . . . . . . . . . . . . . . . . . . . . . . 30
Special DVD Features . . . . . . . . . . . . . . . . . . . . . . . 30
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the Audio Language . . . . . . . . . . . 30
Changing the Audio Channel . . . . . . . . . . . . 30
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Operation with Audio CD and MP3/WMA Discs . . . 31-32
Playing an Audio CD and MP3/WMA Discs . . . . . . . 31
Notes on MP3/WMARecordings. . . . . . . . . . . . . . . . 31
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Moving to another Track. . . . . . . . . . . . . . . . 32
Repeat Track/All/Off . . . . . . . . . . . . . . . . . . . 32
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 32
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 32
Changing the Audio Channel . . . . . . . . . . . . 32
Operation with JPEG Disc . . . . . . . . . . . . . . . . . . 33
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 34
Programmed Playback with Audio CD
and MP3/WMADiscs . . . . . . . . . . . . . . . . . . . . . . . . 34
Programmed Playback with Video CD . . . . . . . . . . . 34
Repeat Programmed Tracks. . . . . . . . . . . . . 34
Erasing a Track from Programme list . . . . . . 34
Erasing the Complete Programme list . . . . . 34
Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Additional Information . . . . . . . . . . . . . . . . . . . . . 35
Additional Operation - VCR part . . . . . . . . . . . 36-37
On Screen Display . . . . . . . . . . . . . . . . . . . . . . . 36
Tape Counter Memory Stop . . . . . . . . . . . . . . . . 36
Friendly User Guide (Video Doctor) . . . . . . . . . . 36
ez (easy) Repeat . . . . . . . . . . . . . . . . . . . . . . . . 36
Hi-Fi Stereo Sound System . . . . . . . . . . . . . . . . 37
Widescreen Compatibility 16:9 . . . . . . . . . . . . . . 37
Special Recording . . . . . . . . . . . . . . . . . . . . . . . . . 38
Copying from DVD to VCR . . . . . . . . . . . . . . . . . 38
Recording from another video recorder . . . . . . . 38
Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 39-40
Presetting the Radio Stations . . . . . . . . . . . . . . . 39
Listening to the Radio . . . . . . . . . . . . . . . . . . . . 39
To Clear the Stored Radio Stations. . . . . . . . . . . 39
Tuning into a Station Manually . . . . . . . . . . . . . . 40
Tuning into a Station Automatically . . . . . . . . . . . 40
RDS Operation . . . . . . . . . . . . . . . . . . . . . . . . . 40
Reference
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 41
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 42
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 43-44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 45-46
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.

4
Before Use
Playable Discs
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play a SVCD, DVD-RW,
DVD+RW, Kodak PICTURE CD and CD-R or CD-RW
that contains audio titles, MP3, WMA or JPEG files.
otes
–Depending on the conditions of the recording equip-
ment or the CD-R/RW (or DVD-RW, DVD+RW) disc
itself, some CD-R/RW (or DVD-RW, DVD+RW) discs
cannot be played on the unit.
–Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
–
Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
otes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs may
be intentionally fixed by software manufacturers. As this
unit plays DVDs and Video CDs according to disc con-
tent designed by the software manufacturer, some play-
back features of the unit may not be available or other
functions may be added.
Make sure to also refer to the instructions supplied with
the DVDs and Video CDs. Some DVDs made for busi-
ness purposes may not be able to be played on the unit.
Regional code of the DVD/CD/VCR receiver and
DVDs
This DVD/CD/VCR receiver is designed and manufac-
tured for playback of region “2” encoded DVD
software. The region code on the labels of some
DVDs indicates which type of player can play
those discs. This unit can only play DVDs labeled
“2” or “ALL”. If you try to play any other discs, the mes-
sage “Check Regional Code” will appear on the TV
screen. Some DVDs that have no region code label may
still be subject to area restrictions and therefore not
playable.
Disc-related terms
Title (DVD only)
The main film content or accompanying feature content
or additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chap-
ters. Each chapter is assigned a chapter number,
enabling you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD
or an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into sec-
tions called “Scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Types of video CDs
There are two types of video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in
the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
2

INTRODUCTION
5
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials may
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be disturbed during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
To keep the exterior surfaces clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzene, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The
DVD/CD/VCR receiver
is a high-tech, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Disc Handling
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sun-
light, as there may be a considerable temperature
increase inside the car.
Cleaning discs
Fingerprints and dust on the disc can distort the picture
or reduce sound quality. Before playing, clean the disc
with a clean cloth. Wipe the disc from the centre out-
wards.
Do not use strong solvents such as alcohol, benzene,
thinner, commercially available cleaners, or anti-static
spray intended for vinyl records.
About Symbols
About the symbol display
“ ” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbol is
applicable only to the disc represented by the symbol.
DVD
Video CDs with the PBC (playback control)
function
Video CDs without the PBC (playback control)
function
Audio CDs.
MP3 disc
WMA disc
JPEG disc
JPEG
WMA
MP3
CD
VCD1.1
VCD2.0
DVD
Setting the Output Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
•If you want to view output source of DVD deck:
Press DVD on the remote or DVD/VCR on the front panel
until DVD indicator on the front panel lights and output
source of DVD deck is viewed on the TV screen.
•If you want to view output source of VCR deck:
Press VCR on the remote or DVD/VCR on the front panel
until VCR indicator on the front panel lights and output
source of VCR deck is viewed on the TV screen.

6
Front Panel Controls
PAUSE/STEP(XX/CC)
Pause playback of a tape or a disc in the DVD or
VCR deck temporarily.
Press repeatedly for frame-by-frame playback.
OPEN/CLOSE (ZZ)
Opens or closes the disc tray.
Remote Sensor
Point the DVD/CD/VCR receiver
remote control here.
Display window
Disc Tray (DVD deck)
Insert a disc here.
STANDBY/ON indicator
Switches the DVD/CD/VCR receiver ON and OFF.
DVD/VCR (output select)
Select one of your output sources to view
on the TV screen between DVD and VCR.
REC/ITR (zz)
To record normally or to activate Instant Timer Recording.
STOP (xx)
Stops playback of a disc or
tape.
AV3((VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external source (Audio system,
TV/Monitor, Another VCR).
Cassette Compartment
(VCR deck)
Insert a video cassette here.
EJECT(ZZ)
Ejects the tape in the VCR deck.
PLAY (B)
To play back a recorded tape or disc.
Forward SKIP/SCAN (
RR
/
TT
)
DVD: Go to NEXT chapter/track. Press and hold for two seconds for a fast
forward search.
VCR: Advances the tape during the STOP mode or for fast
forward picture search.
Reverse SKIP/SCAN (
SS
/
QQ
)
DVD: Go to beginning of current chapter/track or to previous
chapter/track. Press and hold for two seconds for a fast reverse
search.
VCR:
Rewinds the tape during the STOP mode or for fast reverse picture
search.
PROG/TUNING (44/33)
To scan up or down through memorized channels or
to control tracking during playing back a tape (VCR mode).
To tune in the desired station (Radio Mode).
DVD/VCR indicator
Indicates the active deck.
COPY/MEMORY
Press to copy a DVD in the DVD
deck to a VHS tape in the VCR
deck.
Enter a radio stations frequency
into the tuner.
FM/AM
To change between AM and
FM bands.
VOLUME Control
Turn the knob clockwise to increase volume,
counterclockwise to decrease the volume.

INTRODUCTION
7
Display Window Indicators
MUTERECCOPY
CHP/TRKPROG
RADIO
dts
VCD
RPT ALL
A B
MP3 TV
DVD RDS
PROLOGIC II
DIGITAL
PCM WMA
PHOTO
ST
Hi-Fi
MUTE indicator
MP3 disc inserted.
Indicates current chapter,
track number or
channel number.
Indicates current
audio stream.
Indicates current
surround mode.
Repeat playback
mode indicators.
Total playing time/Elapsed time/
Frequency/remaining time/ Current
deck status/Surround mode/Volume
etc. indicators.
A cassette
is loaded
in the VCR
deck.
Indicates the unit is
radio mode.
JPEG disc inserted.
Lights up when a stereo broadcast
is being received in radio mode.
Lights up when the FM
station tuned is trans-
mitting RDS data.
A disc is loaded in the DVD deck. (Lights when a disc is
loaded in the DVD deck.)
DVD/CD/VCR receiver is in VCR timer recording
mode or a VCR timer recording is programmed.
DVD to VCR copy is in progress.
DVD/CD/VCR receiver is Recording a tape.
Indicates the unit is
playing back a tape
recorded in Hi-Fi.
DVD disc inserted.
WMA disc inserted
VCD disc inserted.
Indicates the unit is TV mode.
Programmed
playback active

8
Remote Control Buttons
FM/AM AV SELECT
OPEN/CLOSE
EJECT
MUTE
SOUND MODE
AUDIO
TITLESUBTITLE
AV
ENTER
MEMORY
OK
RETURN
CM SKIP
STOP
PAUSE/STEP
PLAY
BACKWARD FORWARD
REC/ITR
REPEAT
A-B
SPEED
REPEAT TV/VCR
DISC MENU
DISPLAY
CLK/CNT
PR/TRK/PRESET
PR/TRK/PRESET
SETUP/
i
TUN
-ING
TUN
-ING
VOLUME
MARKER
SEARCH
ANGLEZOOM
PROGRAM CLEAR
CD/DVD VCR
POWER
RDS
FM/AM Tuner select button
Select the DVD/CD/VCR receiver’s tuner as the
listening choice. (FM and AM bands)
OPEN/CLOSE, EJECT (ZZ)
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
CD/DVD/VCR select buttons
Select the output source (CD/DVD or
VCR) to view on the TV screen.
RDS
To check the RDS service programme (PS).
0-9 numerical buttons
Selects numbered options in a menu.
ANGLE
Selects a DVD camera angle if
available.
PROGRAM
Accesses or removes Program menu.
ZOOM
Enlarges DVD video image.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
DISPLAY, CLK/CNT
Accesses On-Screen display.
Switches among the clock, tape counter
and tape remaining modes on the display.
b/B/v/V(left/right/up/down)
- Selects an option in the menu.
- PR/TRK/PRESET(v/V):
Select programme of VCR or Tuner
Adjusts manually the tape’s picture
onscreen.
- TUNING (b/B):
To tune in the desired radio
station.
RETURN
Removes the setup menu.
CM SKIP
Fast forwards picture search through 30
seconds of recording.
STOP (xx)
Stops playback.
REC/ITR (zz)
Records normally or activates Instant
Timer Recording.
REPEAT A-B/SPEED/REPEAT
-Repeat chapter, track, title, all.
- ez (easy) repeat (see page 36.)
- Repeats sequence.
- Selects recording speed.
TV/VCR
To view channels selected by the VCR
tuner or by the TV tuner.
POWER
Switches DVD/CD/VCR receiver ON and
OFF.
AV SELECT
Select input source.
MUTE
Momentarily silence the speaker of the
DVD/CD/VCR receiver.
SOUND MODE
Selects sound mode between BYPASS,
PRO LOGIC, PRO LOGICII (MOVIE,
MUSIC, MATRIX) and 3D SURROUND.
CLEAR
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
Press to clear preset stations from the
tuner memory.
AUDIO
Selects an audio language (DVD) or an
audio channel (CD).
SUBTITLE
Selects a subtitle language.
TITLE
Displays the disc’s Title menu, if
available.
AV
Selects the VCR deck’s source
(Tuner, AV1, AV2 or AV3).
VOLUME (+/-)
Adjusts speaker volume.
SETUP/i
Accesses or removes DVD setup menu
and VCR menu.
MEMORY/OK/ENTER
-Enter a radio stations frequency into
the tuner.
-Displays functions on the TV screen.
-Acknowledges menu selection.
DISC MENU
Accesses menu on a DVD disc.
PAUSE/STEP (XX/CC)
Pause playback or recording
temporarily/press repeatedly for
frame-by-frame playback.
PLAY (NN)
Starts playback.
BACKWARD (..)
DVD: Search backward*/go to begin-
ning of current chapter or track or go to
previous chapter or track.
VCR: Rewinds the tape in STOP mode
or for fast reverse picture search.
*Press and hold button for about two
seconds.
FORWARD (>>)
DVD: Search forward*/go to next
chapter or track.
VCR: Advances the tape in STOP
mode or for fast forward picture search.
*Press and hold button for about two
seconds.
ote
This remote control use the same buttons for VCR and DVD functions (ex. PLAY).
To use the VCR, first press the VCR button.
To use the DVD, first press the CD/DVD button.

PREPARATION
9
Rear Panel Connections
ANTENNA
GND
AM S-VIDEO OUT
DVD/VCR
OUT
AERIAL
FM SPEAKER
FRONT
(R 4 )
(R 4 )
REAR CENTER
( 4 )
REAR
(L 4 )
FRONT
(L 4 )
SUB
WOOFER
( 8 )
VCR IN+OUT/DVD OUT
EURO AV2
AUDIO/VIDEO
EURO AV1
AUDIO/VIDEO
RF . OUT
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
AERIAL
Connect the aerial using this jack.
AC Power Cord
Plug into the power source.
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV.
FOR DVD VIEWING ONLY.
RF. OUT
Connect to a TV with RF cable.
SPEAKER CONNECTORS
Connect the six supplied speakers to
these terminals.
FM ANTENNA CONNECTOR
Connect the FM antenna to this terminal.
AM ANTENNA CONNECTORS
Connect the AM antenna to this terminal.
EURO AV1 AUDIO/VIDEO (VCR IN+OUT/DVD OUT)
Connect to your TV set or another video recorder.
EURO AV2 AUDIO/VIDEO (VCR IN+OUT/DVD OUT)
Connect to Set Top Box or another video recorder.
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
Distance: About 6m (20ft) from the front of the
remote sensor
Angle: About 30° in each direction of the front of the
remote sensor
Remote control battery installation
Detach the battery cover on the rear of
the remote control, and insert two R03
(size AAA) batteries with and
aligned correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
AAA
AAA

10
Connections
ANTENNA
GND
AM S-VIDEO OUT
DVD/VCR
OUT
AERIAL
FM SPEAKER
FRONT
(R 4 )
(R 4 )
REAR CENTER
( 4 )
REAR
(L 4 )
FRONT
(L 4 )
SUB
WOOFER
( 8 )
VHS IN+OUT/DVD OUT
EURO AV1
AUDIO/VIDEO
EURO AV2
AUDIO/VIDEO
RF . OUT
S-VIDEO
INPUT
AERIAL
Rear of TV
S
A
D
E
R
SCART INPUT
Set Top Box(or another VCR)
Make one of the following connections, depending on
the capabilities of your existing equipment.
ips
Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the
DVD/CD/VCR receiver
.Use one of the connec-
tions described below.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
Caution
–
Make sure the DVD/CD/VCR receiver is connected
directly to the TV. Select the correct AV input on your
TV.
–Do not connect your DVD/CD/VCR receiver to TV via
your VCR. The DVD image could be distorted by the
copy protection system.
Basic connections (AV)
11
Connect the EURO AV1 AUDIO/VIDEO on the rear
panel of the DVD/CD/VCR receiver to the scart input
socket on the TV using a SCART lead (E).
22
You can connect such a Set Top Box (or another
VCR) to the DVD/CD/VCR receiver (D).
Basic connections (RF)
11
Connect the aerial cable (A) from your indoor/ out-
door aerial to AERIAL jack on the rear panel of
DVD/CD/VCR receiver .
22
Connect the supplied RF cable (R) from the
RF. OUT jack on the rear panel of DVD/CD/VCR
receiver to your television’s Aerial Input.
S-Video connection
Connect the S-VIDEO OUT jack on the DVD/CD/VCR
receiver
to the S-VIDEO IN jack on the TV using the S-
Video cable (S).
otes
The signal of S-VIDEO OUT jack will output only
when the function mode is selected to CD/DVD.
When you connect the
DVD/CD/VCR receiver to your
TV, be sure to turn off the power and unplug both
units from the wall outlet before making any connec-
tions.
TV & Set Top Box (or another VCR Connections)

11
PREPARATION
Connections (Continued)
ANTENNA
GND
AM S-VIDEO OUT
DVD/VCR
OUT
AERIAL
FM SPEAKER
FRONT
(R 4 )
(R 4 )
REAR CENTER
( 4 )
REAR
(L 4 )
FRONT
(L 4 )
SUB
WOOFER
( 8 )
VCR IN+OUT/DVD OUT
EURO AV1
AUDIO/VIDEO
EURO AV2
AUDIO/VIDEO
RF . OUT
FM Wire aerial (supplied) AM Loop aerial (supplied)
Radio Aerial Connections
Connect the supplied FM/AM aerial for listening to the radio.
Connect the AM loop aerial to the AM aerial connector.
Connect he FM wire aerial to the FM aerial connector.
otes
To prevent noise pickup, keep the AM loop aerial away from the DVD/CD/VCR receiver and other components.
Be sure to fully extend the FM wire aerial.
After connecting the FM wire aerial, keep it as horizontal as possible.
Accessory Audio/Video (A/V) Connections to DVD/CD/VCR receiver
Connect the AV3 jacks on the
DVD/CD/VCR receiver to the audio/video out jacks on your accessory component,
using the optional audio/video cables.

12
otes
Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are
reversed, the sound will be distorted and will lack base.
If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers.
Do not remove the front cover of supplied speaker.
Connections (Continued)
ANTENNA
GND
AM S-VIDEO OUT
DVD/VCR
OUT
AERIAL
FM SPEAKER
FRONT
(R 4 )
(R 4 )
REAR CENTER
( 4 )
REAR
(L 4 )
FRONT
(L 4 )
SUB
WOOFER
( 8 )
VCR IN+OUT/DVD OUT
EURO AV1
AUDIO/VIDEO
EURO AV2
AUDIO/VIDEO
RF . OUT
Front Speaker
(Right)
Front Speaker
(Left)
Centre Speaker
Rear Speaker
(Right Surround)
Subwoofer
Rear Speaker
(Left Surround)
Speaker System Connection
Connect the speakers using the supplied speaker cords.
To obtain the best possible surround sound, adjust the speaker parameters; distance, level, etc..

PREPARATION
13
Connections (Continued)
Centre Speaker
Front Speaker
(Left)
Speaker Positioning Example
Rear Speaker
(Left)
Rear Speaker
(Right)
Front Speaker
(Right)
Subwoofer
Speaker Positioning
In the case of normal position use the 6 speakers (2 front speakers, centre speaker, 2 rear speakers and
subwoofer).
If you want to play the excellent bass sound, DTS digital surround or Dolby Digital surround, you should connect a
subwoofer.
•Front speakers
According to your listening position set up the speakers for equal distance. And by hearing position set up the
interval between speakers to 45 degree.
•Centre speaker
The centre speakers and front speakers are ideally the same height. But normally place it above or below the
television.
•Rear speakers
Place left and right behind the listening area. These speakers recreate sound motion and atmosphere required for
surround sound playback. For best results, do not install the rear speakers too far behind the listening position
and install them at or above the level of the listener’s ears. It is also effective to direct the rear speakers towards a
wall or ceiling to further disperse the sound.
In the case of a smaller room size, if the audience is near to the rear wall set the rear speakers opposite each
other, and set the rear speakers above 60 - 90 cm than the listener’s ears.
•Subwoofer
This can be placed in any front position.

14
Mini Glossary
Mini Glossary for Audio Stream &
Surround mode
Allows you to enjoy 5.1(or 6) discrete channels of high quality
digital audio from DTS program sources such as discs, DVD
and compact discs, etc.bearing the trademark. DTS Digital
Surround delivers up to 6 channels of transparent audio(which
means identical to the original masters) and results in excep-
tional clarity throughout a true 360 degree sound field. The
term DTS is a trademark of DTS Technology, LLC.
Manufactured under license from DTS Technology, LLC.
The Dolby Digital surround format lets you enjoy up to 5.1
channels of digital surround sound from a Dolby Digital pro-
gram source. If you play DVDs with “ ” mark, you can enjoy
even better sound quality, greater spatial accuracy, and
improved dynamic range.
Use this mode when playing movie or Dolby Digital 2 channel
which carries the “ ” mark. This mode provides the effect
of being in a movie theatre or live concert house-an effect with
an intensity which can only be obtained through DOLBY PRO
LOGIC SURROUND. The effect of the front/back/left/right
movement of the sound image, as well as the sense of fixed
position in the sound image, is much clearer and more dynam-
ic than before.
(II)
Dolby Pro Logic II creates five full-bandwidth output channels
from two-channel sources. This is done using an advanced,
high-purity matrix surround decoder that extracts the spatial
properties of the original recording without adding any new
sounds or tonal colorations.
MOVIE mode:
The Movie mode is for use with stereo television shows and all
programs encoded in Dolby Surround. The result is enhanced
soundfield directionality that approaches the quality of discrete
5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music recordings,
and provides a wide and deep sound space. The Music mode
includes controls that allow the sound to be tailored to individual
listening tastes.
MATRIX mode:
The Matrix mode is the same as the Music mode except that the
directional enhancement logic is turned off. It may be used to
enhance mono signals by making them seem “larger.” The Matrix
mode may also find use in auto systems, where the fluctuations
from poor FM stereo reception can otherwise cause disturbing
surround signals from a logic decoder. The ultimate “cure” for
poor FM stereo reception may be simply to force the audio to
mono.
3D SURROUND
This unit can produce a 3D Surround effect, using 3D Surround
Sound technology, which simulates multi-channel audio play-
back from two conventional stereo speakers instead of the five
or more speakers normally required to listen to multi-channel
audio from a home theatre. This feature works with DVD discs
encoded with Dolby Pro Logic and Dolby Digital audio tracks.
BYPASS
Software with multichannel surround audio signals is played
according to the way it was recorded.
Sound Mode
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
program you want to listen to.
Press SOUND MODE repeatedly until the sound mode
you want appears in the display window as below.
Each time you press SOUND MODE button, the sound
mode is changed in the following order;
PRO LOGIC →PL2 MOVIE → PL2 MUSIC →PL2 MATRIX →
3D SURROUND →BYPASS
When DVD is inserted.
You can change the stream of DVD (Dolby Digital, DTS, PCM,
etc) by pressing the AUDIO button on the remote during play-
back.
Although the DVD contents differ from disc to disc, the follow-
ing explains the basic operation when this feature is used.
Each time you press AUDIO button, the sound mode of DVD is
changed as the following order;
→→→
For your reference
• The DVD/CD/VCR Receiver memorizes the last
mode
settings for each source individually.
•
You can identify the encoding format of program
software by looking at its packaging.
-Dolby Digital discs are labeled with the logo.
-Dolby Surround encoded programs are labeled with
the logo.
-DTS Digital Surround discs are marked with DTS.
ote
When you play sound tracks with 96kHz sampling frequen-
cy, the output signals will be converted to 48kHz (sampling
frequency).

PREPARATION
15
Before Operation - VCR part
Video channel Set
Video channel (RF output channel) is the channel on
which your TV receives picture and sound signals from
the DVD/CD/VCR receiver through the RF cable.
If you have used a SCART lead you will not have to tune
your TV, simply select the AV channel. The AV channel
is already pre-tuned for optimum video playback on your
TV.
Perform the following steps only if interference appears
in the TV picture after you have moved to a different
area or a new station has started broadcasting in your
area, or if you change the connection from RF connec-
tion to AV connection, or vise versa.
11
Turn on DVD/CD/VCR receiver and TV.
22
Set the vacant position 36 on your TV.
33
Press POWER on the remote control to enter
the standby mode (the clock indicator will be
dimmed).
44
Press and hold PROG DDor EEon the
DVD/CD/VCR receiver for more than 4 secs.
RF 36 will appear in the DVD/CD/VCR receiver display.
The following picture will be displayed on the TV
screen.
If the picture is snowy, move to step 5. If the picture
is clean, press POWER on the DVD/CD/VCR
receiver to finish.
55
Press PROG DDor EEon the DVD/CD/VCR receiv-
er to set the video channel to a vacant position
between 22 and 68 which is not occupied by
any local station in your area.
ote
The RF channel will not change until step 6 has been
executed.
66
Press POWER on the DVD/CD/VCR receiver to
store the new RF video channel into the
DVD/CD/VCR receiver memory.
Now tune your TV set to the new DVD+VCR RF
channel.
ote
If the TV picture was clear in step 4, do not retune your
TV.
Using your Receiver for the very first time
For the following steps we assume that you have just
connected your Receiver for the very first time.
To make tuning TV stations an easy task your Receiver
incorporates the Automatic Channel Memory System
(ACMS).This system will automatically tune and store
TV channels in your Receiver.
11
Make sure that you have correctly installed your
DVD/CD/VCR receiver.
22
Press POWER to turn on your DVD/CD/VCR
receiver.
If the initial Menu Screen doesn’t appear on screen,
make sure that you have tuned your TV to a video
channel. Or if this is correct it may mean that your
DVD/CD/VCR receiver is already tuned.
33
Press OK to start the automatic tuning process.
44
Press i to remove the menus from the TV
screen.
i
RF CHANNEL 36
SET
P
R
01 C02 00 PR-01
02 C03 00 PR-02
03 C04 00 PR-03
ES
i
Pr-12
ACMS
OK i
Pr-12
ACMS
ACMS

16
Before Operation - VCR part
How to use the main menu
This DVD/CD/VCR receiver can easily be programmed
by using the menus displayed on screen.
The menus are controlled from the Remote Control
Handset.
11
Switch on your TV set and DVD/CD/VCR recei-
ver by pressing the POWER.
22
Press i.
The main menu will appear on the TV screen.
REC
Timer recording setting (see p. 26-27).
PR SET
Manual tuning setting (see p. 17).
ACMS
ACMS (Automatic Channel Memory System) (see
right column).
TIME DATE
Date & clock setting (see p. 19).
OSYSTEM
To set the Colour TV System (see p. 19).
OABC OSD
To change the language setting for OSD.
You can select the language from English, Russian,
German, Polish, Czech and Hungarian.
ODr.
To check a problem with your DVD/CD/VCR receiver
(see p. 36).
OfOSD ON/OFF
To display the operational mode of your
DVD/CD/VCR receiver (see p. 36).
O16:9/4:3
To select the aspect ratio of your TV (see p. 37).
OOPR
To improve the playback picture (see p. 24).
ONIC
To activate or deactivate the NICAM digital sound
(see p. 37).
33
Press 11or 22to select the desired menu.
44
Press OK and press 33or 44to select.
55
Press ito return to a TV picture.
Tuning in TV Stations Automatically
Should you wish to perform the Automatic Channel
Memory System (ACMS) again please follow the guid-
ance given on this page. You may tune up to 88 TV sta-
tions into your DVD/CD/VCR receiver.
11
Press POWER to turn on your DVD/CD/VCR
receiver.
22
Press i.
The main menu will appear on the TV screen.
33
Press FFor GGto select ACMS and press OK.
44
Press OK again to start the automatic tuning
process.
55
Press i to remove the menus from the TV
screen.
REC REC
OK i
SYS-
TEM
AB
C
OSD
PSET
R
Dr.
VCR
Pr-12
ACMS
OSD
ON
OFF
OSD
f
12
TIME
DATE
16:9
4:3
OPR
NIC
02 C03 00 PR-02
03 C04 00 PR-03
04 C05 00 PR-04
05 C06 00 PR-05
06 C07 00 PR-06
07 C08 00 PR-07
08 C09 00 PR-08
01 C02 00 PR-01
P
RSET
OK i
,DELETE :
MOVE :
01 C02 00 PR-01
02 C03 00 PR-02
03 C04 00 PR-03
ES
i
Pr-12
ACMS
OK i
Pr-12
ACMS
ACMS

PREPARATION
17
Before Operation - VCR part
Tuning in TV Stations Manually
In certain areas of the country broadcast signals may
be too weak for your DVD/CD/VCR receiver’s automatic
tuning process to find or assign TV stations correctly.
You must tune in these weaker broadcast stations man-
ually in order for your DVD/CD/VCR receiver to store
them.
11
Press i.
The main menu will appear on the TV screen.
22
Press FFor GGto select PR SET and press OK.
33
Press iand press DDor EEto select the pro-
gramme number that you want to tune (for
example, PR 07). Press OK.
44
Press AV to select C (Standard stations) or S
(Cable stations): C02 - C70, S01 - S41.
Enter the channel number of station that you want
to tune with the numerical buttons.
55
Searching will stop when it locates a station.
Control the fine tuning of the station by pressing D
or E.
66
Press GGto select STATION and press OK.
77
Press DDor EEto select letters and numbers for
the new station name.
Press FFor GGto move back and forth between
characters. Press OK.
88
Press i,confirm the station placement.
99
Press ito remove the menus from the TV
screen.
Your new TV station has now been tuned into your
DVD/CD/VCR receiver.
If you wish to manually tune other stations repeat
stages 1 - 8.
PR CH STATION
01 00 PR-01
i
C 02
MFT
CHANNEL/CABLE : AV
SET
P
R
02 C03 00 PR-02
03 C04 00 PR-03
04 C05 00 PR-04
05 C06 00 PR-05
06 S07 00 PR-06
- - - - - - - - -
- - - - - - - - -
07
08
01 C02 00 PR-01
OK i
,DELETE :
MOVE :
P
RSET
PR CH STATION
07 00
C40
MFT
i
P
RSET
CHANNEL/CABLE : AV
PR CH STATION
07 +04
C 02
MFT
CHANNEL/CABLE : AV
OK
i
P
RSET
PR CH MFT STATION
07 +04
C02 TV2
i
OK
P
RSET
02 C03 00 PR-02
03 C04 00 PR-03
04 C05 00 PR-04
05 C06 00 PR-05
06 S07 00 PR-06
C02 +04 TV2
- - - - - - - - -
07
08
01 C02 00 PR-01
P
RSET
OK i
PR CH STATION
07 - - - - - - -
C - -
MFT
CHANNEL/CABLE : AV
i
P
RSET
PR CH STATION
07 +04
C 02
MFT
OK
i
P
RSET
OK

18
Before Operation - VCR part
Changing the order of TV Stations
After tuning TV stations into your DVD/CD/VCR receiver
you may wish to change the order in which they are
stored without having to retune them. The instructions
given on this page will show you how you can simply
move them into your desired order
11
Press i.
The main menu will appear on the TV screen.
Press FFor GGto select PR SET and press OK.
22
Press i.
Press DDor EEto select the programme number
you want to move (for example, PR 03).
Press GG.
33
Press DDor EEto select the programme number
you want to move to (for example, PR 05).
44
Press OK.
The selected programme will be moved to the new
programme number.
55
Press i to remove the menus from the TV
screen.
If you wish to move other TV stations repeat stages
1 - 4.
Deleting TV Stations
After tuning TV stations into your DVD/CD/VCR receiver
you may wish to delete a station.
The instructions given on this page will show you how to
easily delete any unwanted TV stations.
11
Press i.
The main menu will appear on the TV screen.
Press FFor GGto select PR SET and press OK.
22
Press i.
Press DDor EEto select the programme number
you want to delete (for example, PR 03).
33
Press FF.
After a short while, the selected station will be
deleted.
44
Press i to remove the menus from the TV
screen.
If you wish to delete other TV stations repeat stages
1 - 3.
How to select Stored TV stations:
Stored TV stations can be selected in either of two
ways.
Press Dor Eto select different stations that are
tuned into your DVD/CD/VCR receiver.
You may also directly select stations using the
numerical buttons on the remote control.
PR CH MFT STATION
01 00 PR-01
CHANNEL/CABLE : AV
C 02
i
P
RSET
C04 00
02
C02 00 PR-01
C03 00 PR-02
04 C05 00 PR-04
05 C06 00 PR-05
06 C07 00 PR-06
07 C08 00 PR-07
08 C09 00 PR-08
01
OK i
03
P
RSET
PR-03
C04 00 PR-03
02
C02 00 PR-01
C03 00 PR-02
04
C05 00 PR-04
05
C06 00 PR-05
06 C07 00 PR-06
07 C08 00 PR-07
08 C09 00 PR-08
01
OK i
03
P
RSET
C04 00 PR-03
02
C02 00 PR-01
C03 00 PR-02
04
C05 00 PR-04
05
C06 00 PR-05
06 C07 00 PR-06
07 C08 00 PR-07
08 C09 00 PR-08
01
03
P
RSET
OK i
,DELETE :
MOVE :
PR CH MFT STATION
01 00
CHANNEL/CABLE : AV
C 02
i
P
RSET
C04 00 PR-05
02
C02 00 PR-01
C03 00 PR-02
04
C05 00 PR-03
05
C06 00 PR-04
06 C07 00 PR-06
07 C08 00 PR-07
08 C09 00 PR-08
01
03
OK i
,
DELETE :
P
RSET
MOVE:
C04 00 PR-04
02
C02 00 PR-01
C03 00 PR-02
04
05
C06 00 PR-03
06
C07 00 PR-05
07
C08 00 PR-06
08
C09 00 PR-07
- - - - - - - - -
01
03
OK i
,
DELETE :
MOVE:
P
RSET

PREPARATION
19
Before Operation - VCR part
Setting the Clock Manually
11
Press i.
Press FFor GGto select TIME DATE and press
OK.
22
Use the numerical buttons or press ▲/▼or FF/GG
on the remote control to alter the HOURS, MIN-
UTES, DAY, MONTH and YEAR.
Please note your DVD/CD/VCR receiver uses a 24-
hour clock. e.g. 1pm will be displayed as 13:00.
The day of the week will appear automatically when
you enter the year.
33
If you make a mistake, press FFor GGand enter
the correct details.
44
Press ito remove the menus from the TV
screen.
Your new clock settings are stored and will appear
on your DVD/CD/VCR receiver’s Display.
To set the colour system
Your DVD/CD/VCR receiver is equipped with dual colour
standard, you can play back a tape in PAL and MESE-
CAM.
During playback your DVD/CD/VCR receiver detects the
colour system automatically.
If there is any colour problem please select the colour
system manually.
11
Press i.
The main menu will appear on the TV screen.
22
Press FFor GGto select the SYSTEM.
33
Press OK and press DDor EEto select according
to the COLOUR system used.
AUTO:
Allows PAL or MESECAM signals to be distinguished
automatically.
PAL:
Use when receiving PAL signals or use when playing
back a tape recorded in PAL system.
MESECAM:
Use when receiving MESECAM signals or use when
playing back a tape recorded in MESECAM system.
44
Press FFor GGto select the RF AUDIO and press
DDor EEto select according to the RF AUDIO
used.
55
Press ito remove the menus from the TV
screen.
HH MM DD MM YY
:..- -
- - - - - - - - - - -
i
12
TIME
DATE
HH MM DD MM YY
:..45 1 01 03 WED
i
12
TIME
DATE
11
REC
OK i
PR
Pr-12
ACMS
12
TIME
DATE
SYS-
TEM SYS-
TEM
OPR
OSD
ON
OFF
OSD
f
16:9
4:3
NIC
RF I/I
RF B/G
RF D/K
AB
C
OSD
Dr.
VCR
REC
OK i
AB
C
OSD
Dr.
SET
P
R
VCR
Pr-12
ACMS
12
TIME
DATE
SYS-
TEM SYS-
TEM
OSD
ON
OFF
OSD
f
16:9
4:3
OPR
NIC
REC
OK i
PR
Pr-12
ACMS
12
TIME
DATE
SYS-
TEM SYS-
TEM
OPR
OSD
ON
OFF
OSD
f
16:9
4:3
NIC
AUTO
PAL
MESECAM
AB
C
OSD
Dr.
VCR

20
Before Operation - DVD part
General Explanation
This manual gives basic instructions for operating the
DVD/CD/VCR receiver. Some DVDs require specific
operation or allow only limited operation during play-
back. When this occurs, the symbol appears on the
TV screen, indicating that the operation is not permitted
by the DVD/CD/VCR receiver or is not available on the
disc.
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
11
Press DISPLAY during playback.
22
Press 33/44to select an item.
The selected item will be highlighted.
33
Press 11/22to change the setting of an item.
The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press ENTER to execute the setting.
Temporary Feedback Field Icons
Repeat Title
Repeat Chapter
Repeat Track (non-PBC Video CDs only)
Repeat All Tracks (non-PBC Video CDs only)
Repeat A-B
Repeat Off
Resume play from this point
Action prohibited or not available
otes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
OFF
A B
ALL
TRACK
CHAPT
TITLE
Items
Title Number
Chapter Number
Time search
Audio language
and Digital Audio
Output mode
Subtitle language
Angle
Sound
Function (Press 33/44to select desired item)
Shows the current title number and total number of
titles, and skips to the desired title number.
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
Shows the elapsed playing time, and
searches the point directly from the elapsed time.
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and
changes the setting.
Selection Method
11
/
22
,or
Numbers, ENTER
11
/
22
,or
Numbers, ENTER
Numbers, ENTER
11
/
22
,or
AUDIO
11
/
22
,or
SUBTITLE
11
/
22
,or
ANGLE
11
/
22
,or
SOUND MODE
1 /3
1 /12
0:20:09
1 ENG
D
5.1 CH
OFF
1 /1
BYPASS
ABC
Items
Track Number
Time
Audio Channel
Sound
Function (Press 33/44to select desired item)
Shows the current track number, total number of tracks
and PBC On mode, and skips to the desired track number.
Shows the elapsed playing time (Display only)
Shows the audio channel, and
changes the audio channel.
Shows the current sound mode, and
changes the setting.
Selection Method
11
/
22
,or
Numbers, ENTER
–
11
/
22
,or
AUDIO
11
/
22
,or
SOUND MODE
1 /4
0:20:09
STER.
BYPASS
VCD2.0 VCD1.1
DVD