LG Ipsolute LW130W-D User manual

Please read this manual carefully before operating your set and retain it for future reference.
OWNER’S MANUAL
HD Compact Network Camera
MODEL
LW130W
1302(V1.4)

2
Safety Instructions
The following instructions and guidance are for your safe and proper use of the products to prevent damages on
properties and injuries.
Handling of the Product
• Makesureanywaterorotherfluiddoesnotenterthedevice,aswellasmetallicobjectsoranyotherconductivesubstances.
- Fireorelectricshockisfearedifanyfluidsormetallicobjectsenterthedevice.
• Whencleaningthedustsorotherforeignobjectsoffthedevice,usedryclothestowipeoutthesurfacegently.Whenthe
contaminationisheavy,useclothessoakedinneutraldetergents.Donotusethinner,alcohol,benzene,insecticideorother
volatilesubstancesonthesurface.
- Thesurfaceoftheproductortheoperationofthedevicemaynegativelybeaffected.
• Whencleaningthesurfaceofthedevice,alwaysusedryclothes.Donotusewater,chemicals,orcleansingdetergentsas
electricshocksordamagesonthedevicesmayoccur.
• Donotattempttodisassemble,repair,oradjustthedevice.AnydisassemblyattemptsnotbyaqualifiedtechniciansfromLG
Electronicsmaycausefire,electricshocks,orinjuries.
• Donotplaceheavyobjectsontopofthedevice.

3
Safety Instructions
Installation and Storage
• Pleasereadandfollowtheinstructionsbelowcarefullyasyoupreparefortheinstallationofthedevice.
• Shutdownthepowerofthemaindevice
• Reserveenoughspaceforthewiringofthedevicewheninstallingtheproduct.
• Donotinstallinaplacewithhighmoisture,dusts,orsoot.
• Donotinstallunderdirectsunlightorclosetoaheater.
• Donotinstallinaplacewherethereisdangerofelectricshocksorclosetomagneticobjects.
• Installthedeviceinaplacewithappropriatetemperatureandmoisture.(therecommendedtemperaturerangeofoperation
isbetween0°Cand40°C.)
• Makesurethedeviceisinstalledinawell-ventilatedplace.Donotplacethedevicewheretheventilationisbad,under
excessivevibration,orclosetoastrongelectro-magneticwavesource.
• Checkforanysourceofdanger(moisture,possibledamagesonthewires,orinstabilityoftheplacewherethedeviceis
located).Whenyoufindone,pleasecontacttheclosetcustomerservicecenter.

4
Safety Instructions
EU Conformity Notice
LGElectronicsherebydeclaresthatthis/theseproduct(s)is/areincompliancewiththeessentialrequirementsandotherrelevant
provisionsofDirective1999/5/EC,2004/108/EC,2006/95/ECand2009/125/EC
PleasecontacttothefollowingaddressforobtainingacopyoftheDoC(DeclarationofConformity).
EuropeanStandardsCentre:
Krijgsman1,1186DMAmstelveenTheNetherlands
Indooruseonly.
RF Radiation Exposure Statement
Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiatorandyourbody.

5
Safety Instructions
France Notice
Pour la France métropolitaine
2.400-2.4835GHz(Canaux1à13)autoriséenusageintérieur
2.400-2.454GHz(canaux1à7)autoriséenusageextérieur
Pour la Guyane et la Réunion
2.400-2.4835GHz(Canaux1à13)autoriséenusageintérieur
2.420-2.4835GHz(canaux5à13)autoriséenusageextérieur
Italy Notice
AgeneralauthorizationisrequestedforoutdooruseinItaly.
Theuseoftheseequipmentsisregulatedby:
1. D.L.gs1.8.2003,n.259,article104(activitysubjecttogeneralauthorization)
foroutdooruseandarticle105(freeuse)forindooruse,inbothcasesforprivateuse.
2. D.M.28.5.03,forsupplytopublicofRLANaccesstonetworksandtelecomservices.
L’usodegliapparatièregolamentatoda:
1. D.L.gs1.8.2003,n.259,articoli104(attivitàsoggetteadautorizzazionegenerale)seutilizzatialdifuoridelpropriofondoe
105(liberouso)seutilizzatientroilpropriofondo,inentrambiicasiperusoprivate.
2. D.M.28.5.03,perlafornituraalpubblicodell’accessoR-LANalleretieaiserviziditelecomunicazioni.

6
Safety Instructions
FCC Compliance Statement
Thisdevicecomplieswithpart15oftheFCCrules.
Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
NOTE: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15ofthe
FCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.
Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnot
occurinaparticularinstallation.
Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningthe
equipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

7
Safety Instructions
CAUTION : Anychangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’s
authoritytooperatethisequipment.
FCC RF Radiation Exposure Statement :ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforan
uncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator
andyourbody.EndusersmustfollowthespecificoperatinginstructionsforsatisfyingRFexposurecompliance.
Thistransmittermustnotbeco-locatedoroperatinginconjunctionwithanyotherantennaortransmitter.
CAUTION:RegulationsoftheFCCandFAAprohibitairborneoperationofradio-frequencywirelessdevicesbecausetheirsignals
couldinterferewithcriticalaircraftinstruments.
Responsible Party:
LGElectronicsUSA,Inc.
1000SylvanAvenue
EnglewoodCliffs,NJ07632
TEL.:[phone]

8
Contents
Product Characteristics ................................................... 9
Device Overview & Features .......................................... 10
Connecting the Device....................................................13
Cautions.....................................................................13
Connection Scheme .............................................13
Network Connections ........................................... 14
Power Supply........................................................... 15
Connecting Alarming Devices .......................... 16
Using the micro SD Card.................................... 18
Installing the Camera .......................................... 20
Initial Configuration and Operation..............................22
Before Using the System ................................... 22
Recommended PC Requirements................. 23
Connecting LG IP Device................................... 23
Overview of LG Smart Web Viewer ................ 25
Configuration of LG Network Camera........... 28
Things to Check before Reporting a Malfunction...... 60
Open Source Software Disclaimer................................63
Product Specification ....................................................64

9
LGNetworkCameraisamoreconvenient,easy-to-use
network-basedsurveillancesystem.Asyouestablishanetwork
basedsurveillanceenvironmentusingLG’sNetworkCameras,
youcaneasilyperformvarioussurveillancetaskssuchas
thevideomonitoring,recording,configurationsandevent
management.
Withthismanual,youcanlearnhowtoinstallandoperateLG
NetworkCamerainanetworkedenvironmentindetails.Any
priorknowledgeorfamiliaritywiththenetworkenvironment
willbeofassistanceasyoutrytounderstandthismanual.
Ifyouneedfurthertechnicalassistance,contactourcustomer
servicecenters.
• MultiCodecStreaming(H.264_HIGH,H.264,MJPEG)
• Audiosupported(G.711/G.726FullDuplex)
• Ethernet100Mbps
• WirelessLan802.11b/g/n
• DigitalInput/Output:Input1port,Output1port
• ExntendedmemoryusingamicroSDcard(upto32GB)
• Pre/PostAlarmingfeatureandrecording
• HumanMotionDetection
• NightFlashLED(5meterradious)
• AW,AE,Sharpness
Note:
APIRsensorcandetecthumanmotionswithin5mradius.
Product Characteristics

10
Device Overview & Features

11
Device Overview & Features
aStand Connecting Hole
Youcanconnectthecameraontoastandusingthis
hole.
b I/O Terminals
IN(SensorInput)Terminal:Connectasensorhere.
OUT(Relayoutput)Terminal:Connectanalarm(relay)
devicehere.
cPower Socket
ConnectaDC5Vpowersupply.
dEthernet Terminal
Usea10BASE-T/100BAST-TXnetworkcabletoconnect
toaPCoranetworkhub.
eREBOOT
Pushthisbuttontorestartthedevice.
fWPS, Factory Setting
PresstouseWPSorreturnthedevicetofactorydefault
setting.Holdthebuttondownforlessthan4secondsto
activateWPSfeature.
Holdthebuttondownforlongerthan10secondsto
activatethefactorydefaultmode.Oncethepowerlamp
startstoblinkinyellowandgreen,releasethebuttonto
runinfactorydefaultmodel.
WhenaWPSconnectionisestablished,theWirelessLAN
Connectionlampwillblinkinredandgreencolors.Once
thelampturnsgreenandstopsblinking,theconnection
establishmentiscomplete.Redcoloroftheconnection
lampmeansaconnectionfailure.
Note:
Refertothemanualofthenetworkhubortheinternet
servicemanualtofindouthowtouseWPS.Ifthehubis
settoSharedmode,connectiontothehubusingWPS
cannotbeestablished.
gmicro SD Card Slot Cover

12
Device Overview & Features
hmicro SD Card Slot
InsertamicroSDCardhere.
iSpeaker
ItdeliversthesoundfromthemicrophoneofthePCto
thecamera,tobeplayedbythespeakeronthedevice.
jMotion Detector
Detectsmotionsoccurringinvicinityofthedevice.
kFlash LED
TheLEDlampcanbeturnedon/offthroughthe
configurationmode.
lMicrophone
Thesoundscomingfromthevicinityofthedeviceis
deliveredthroughthismicrophonetoaconnectedPC.
mPower Lamp
Turnsoningreencolorwhenthepowersupplyison
andthedeviceisrunning.
nEthernet Connection Lamp
Turnsoningreencolorwhentheethernetconnection
tothenetworkisestablished.
oWireless LAN Connection Lamp
GreenlightmeansthattheWirelessLANconnectionis
successfullyestablished.

13
Cautions
• ShutdownthepowerofthePCbeforeconnectingthedevice.
• Thefollowinginstallationworksandconnectionsshouldbemadebyaqualifiedtechnicianorsystemengineer.Allrelevant
rulesandregulationsshouldbeobserved.
• Donothavethepowercableorconnectioncableexposedtomoisture,whichcancausedamagesonthedevice.
Connection Scheme
Connecting the Device

14
Connecting the Device
Network Connections
Theproductsupportsremotecontrol,adjustmentofthesettings,orrealtimemonitoringoftheimageryvianetworks.
Afterinstallingthedevice,checkyournetworkenvironment.
UseanRJ-45cabletoconnectyourLGNetworkCameratothenetwork.

15
Connecting the Device
Power Supply
ConnectthedevicetoaDC5Vpowersupplyfromtheadapter
asshowninthefigure.
(Therecommendedpowerspecificationoftheadaptoris
DC5V/1.5Aorabove.)
[Adaptor Specication]
Manufacturer AsianPowerDevicesInc.
Type/Model DA-15F05
Rating
Input:100-240V,50-60Hz,0.5A
Output:5Vdc3A

16
Connecting the Device
Connecting Alarming Devices
TheAlarmTerminalsareusedtoconnectthedevicewitha
buzzer,alarmlamp,doorswitchesorotherexternalalarming
devicesorrelays.
ThespecificationoftheAlarmTerminalisasfollows;
1234
OUT IN GND VCC
A
1234
[Alarm Terminal Specication]
Minimum Typical Maximum Remarks
DCOutput 2.9V 3.1V 3.3V
LoadCurrent -50mA 100mA
DigitalInput 2.3V 3.3V 4.3V
DigitalOutput 2.3V 3.3V
CableSpec.
AWG24 AWG16 UL
Standard
0.20mm21.5mm2IEC
Standard
• AbsoluteMaximumRatings
- DigitalInput:-24Vto+24VDC
- DigitalOuput:+3Vto+24VDC/100mAMax
UsethecompatiblecablestoconnecttotheAlarmTerminal.
Pressdownforengagement,andpress“A”Buttontodisengage.

17
Connecting the Device
IN (Sesor Input)
ConnectaSensortotheSensorInputTerminal.
Sensor
Output (Relay Output)
Connectanalarmingdevice(orarelay)totheRelayOutput
Terminalofthedevice.Alarmingsignalswillbegivenincase
ofanevent.
Alarm(Relay)
Device
Note:
ForaPhotoMOSrelay,use
regularvoltagesof
AC28V,100mAor
DC20V,100mA.

18
Connecting the Device
Using the micro SD Card
YoucanuseamicroSDcardtopreventinterruptionof
recordingormonitoringevenwhenthereisanetworkfailure.
Inserting a micro SD Card
1. OpenthemicroSDCardSlotCover.
2. Asillustratedbelow,insertthemicroSDcardwhile
makingsurethedirectionoftheterminalsonthecard
isproperlyaligned.Slideinthecardslowly,andgivea
littlepressureattheendtocompletetheinsertionofthe
card.
Note:
• Donotuseexcessiveforceasyouslideinthecardto
preventdamages.
• Insertingthecardwiththeterminalsfacingthewrong
dirctionmayresultinthedamagesofthecardofthecard
slotonthedevice.
• Keepthemetallicterminalonthecardclearofanyforeign
objectsorcontamination.
• TheSDcardisaconsumableitem.Afteracertainnumber
ofreading/writingoperationsthecardmayexpireandthe
datamaynotbesaved.Inthiscase,replacetheexpired
cardwithanewone.

19
Connecting the Device
Removal of the micro SD Card from the
Device
1. PressdownthemicroSDcardgentlytounlockthecard
fromtheslot.
2. Pullouttoremovethecardwithcare.Ifyouuseexces-
siveforcetopulloutthecardfromtheslotwithoutfirst
unlocking,itmayresultinthedamagesonthecardof
thecardslotonthedevice.
Caution:
• Whenyouremovethecardfromthedeviceasthedevice
isstillrunning,makesurethecardisunmountedfrom
thesystemfirst,byaccessingthe[Unmount]commandin
[SDCard>Settings>DiskManagement]menu.Ifthecard
isremovedwithoutunmountingit,thedatastoredwithin
thecardmaybecompromisedorthedevicewouldnot
workproperly.
• LGElectronicsisnotresponsibleforthedamagesorthe
lostdataduetotheimproperinsertionorremovalofthe
SDcardbytheusers.
Recommended Card Specication
Maker Capacity BlockSize
(FAT32) Others
LG
32GBorless 32kbyte
Read/Write
speed10MB/
Secorabove
(Class6)
Sandisk
Transcend

20
Connecting the Device
Installing the Camera
Ensurethecameraisplacedonasafeandstableposition
wheretheweightofthecameracansecurelybesupported
sustainably.
1. Disconnectthestandfromthebody.
- Turnthenut-covercounterclockwisetoremovethe
coverfromthebody.
2. Fixthestand.
- Detachthestandcoverandfixthestandusingtwo
screwsprovidedwithit.