LG LNU3210R User manual

MODEL
LNU3210R series
Please read this manual carefully before operating
your set and retain it for future reference.
Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.
Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.
Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.
Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.
Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.
Warning: Install the camera on a ceiling or wall
where can withstand the weight of 5 times of
the camera including mounting bracket.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.
Caution: Make sure the power supply voltage
is correct before using the camera.
Caution: Do not drop the camera or subject it
to physical shock.
Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.
Caution: While shipping, the camera should be
packed in its original packing.
Note:
Please make sure the product is installed
appropriate places where secured from flood,
such as under the eaves, to operate properly.
This product is certified as IP66 standard.
However, if there is any flood concerns, it
is highly recommended to use an outdoor
Housing. When you install the camera inside
an outdoor Housing, please use one of the
following methods:
1. Remove the front glass of Housing before
installing the camera.
2. To keep the front glass of Housing, remove
the front cover, and then put the camera
close to the front glass.
The Power Plug is the disconnecting device.
In case of an emergency, the Power Plug
must remain readily accessible.
LG Electronics hereby declares
that this/these product(s)
is/are in compliance with the
essential requirements and
other relevant provisions of
Directive 2004/108/EC and
2011/65/EU.
Contact office for compliance of this
product:
LG Electronics Inc.
EU Representative, Krijgsman 1,1186 DM
Amstelveen, The Netherlands
• Please note that this is NOT a Customer
Service contact point. For Customer
Service Information, see Warranty Card
or contact the dealer that you purchased
this product.
Disposal of your old appliance
1. When this crossed-out
wheeled bin symbol is
attached to a product
it means the product is
covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.
• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
3. The correct disposal of your old appliance
will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased
the product.
EEE Compliance with Directive.
(for Turkey only)
Important Safety
Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Handling of the unit
Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.
• Remove dust or dirt on the surface of the
lens with a blower.
• Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
• This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.
Operating and storage
location
Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
• Extremely hot or cold places (operating
temperature -10 °C to 55 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful
electromagnetic radiation such as radio or
TV transmitters.
• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.
Specication
Item LNU3210R
Camera
Image Device 6.4 mm (1/2.8 Type) CMOS
Lens Type 4 mm F2.0
Day/Night ICR (Auto / Day / Night)
Minimum
Illumination
Color: 0.07 lx @ F2.0 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
IR Distance 30 m
WDR Digital (Dynamic Range Enhancer)
Image
Enhancement
Backlight Compensation, DNR, Exposure Control, AGC,
White Balance, Privacy Masking, Sharpness
Video
Compression H.264_HIGH, H.264, MJPEG
Resolution 1920 x 1080 / 1280 x 720 / D1 (704 x 480) / CIF (352 x 240)
Maximum Frame
Rate 30 fps @ 1920 x 1080
Multi-Streaming Up to 7
ROI (Region of
Interest) Up to 4
Video Analytics Motion detection, Tampering alarm
Event
Event
Notication Email, FTP
Pre Event
Buering Support
Network
Ethernet RJ-45 10 / 100 BASE-T
Security Password Protection, HTTPS(SSL, TLS), IP ltering, IEEE 802.1X
Open Protocol ONVIF 2.2 Prole S, PSIA 1.1
Protocol
IPv4 and IPv6: TCP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,
QoS, UPnP
IPv4: FTP, SMTP, NTP, ARP, SNMPv1/v2c/v3, DDNS(LG)
Connections Up to 10
Integrated
Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)
General
Power Source DC 12 V
Maximum Power
Consumption 6.1 W
Maximum Input
Current 510 mA
Operation
Temperature/
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Protection IP66
Dimension
(W x H x D) 89 mm x 83 mm x 280 mm
Weight 406 g
Note that design and specication of this unit may change from the manual as quality and
improvement without prior notice.
Components
Camera, Installation Manual, Screws (3 EA), Anchor (3 EA), Installation sticker
Символ «не для пищевой продукции»
применяется в соответствие с техническим
регламентом Таможенного союза «О
безопасности упаковки» 005/2011 и указывает
на то, что упаковка данного продукта не
предназначена для повторного использования
и подлежит утилизации. Упаковку данного
продукта запрещается использовать для
хранения пищевой продукции.
Символ Кедендік одақтың 005/2011
техникалық регламентіне сәйкес
қолданылады және осы өнімнің қаптамасын
екінші рет пайдалануға арналмағанын және
жоюға жататынын көрсетеді. Осы өнімнің
қаптамасын азық-түлік өнімдерін сақтау үшін
пайдалануға тыйым салынады.
Символ «петля Мебиуса» указывает на
возможность утилизации упаковки. Символ
может быть дополнен обозначением материала
упаковки в виде цифрового и/или буквенного
обозначения.
Символ қаптаманы жою мүмкіндігін көрсетеді.
Символ сандық код және/немесе әріп
белгілері түріндегі қаптама материалының
белгісімен толықтырылуы мүмкін.
OWNER’S MANUAL
High
Denition
Network
Camera
To view the instructions of advanced features,
visit http://www.lgecommercial.com and then download Owner’s Manual / Software.
Импортер ООО “ЛГ Электроникс Рус”
Адрес импортера: 143160 Российская Федерация, Московская область, Рузский район, сельское поселение Дороховское,
86 км. Минского шоссе, д.9
Адрес производителя: ЛГ ЭЛЕКТРОНИКС (ХУЖОУ) ИНК., ЗАВОД ХАТАИ
ЛГ Электроникс (Хужоу) Инк., завод Хатаи
516006, Китай, пров. ГуанДонг, г. Хужоу, Промышленная зона
Жонгкай, Индустриальный парк Хутаи, ХуФенг Донг Уи Роуд, 13.
Российская Федерация
Сделано в Китае
Reference
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained
in this product, please visit http://opensource.lge.com. In addition to the source code, all referred
license terms, warranty disclaimers and copyright notices are available for download. LG Electronics
will also provide open source code to you on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping and handling) upon email request to
[email protected]. This oer is valid for three (3) years from the date on which you purchased the
product.

Part Names and Functions
ETHERNET
POWER IN
DC - 12 V
a
b
c
d
e
g
h
i
f
aETHERNET
Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached RJ-45
connector.
bPower input terminal
Connects to a DC 12 V power supply using proper cables. This camera must always be operated
a DC 12 V. Certied/Listed Adaptor which comply with LPS.
cPan adjuster
Adjust the pan position.
dTilt adjuster
Adjust the tilt position.
eAngle adjuster
Adjust the camera angle.
fLens Cover
gRESET button
Push the button more than 3 seconds, this would restore the factory default network related
settings.
hIR LED
iIR Sensor
Installation
Mounting the camera
Follow the instructions below to ceiling or wall mount the camera.
1. Use the installation guide template to check the mounting location. Face the front of the label
toward the area of interest. Using the template as a guide, make a hole through the ceiling.
2. Connect the cables to the cable jacks of the camera body.
CABLE
3. Install the camera by using M4 Tapping screws to x it on the ceiling.
CABLE
Connecting Waterproof processing of cable
Surely use the Butyl tape.
1. Connect the cables.
2. Bind the cables together with Butyl tape.
• The cables are not waterproofed completely. So seal the tube ends and the portions
between cable cores as well as connecting portions with Butyl tape.
• If not using the Butyl tape, it may cause water absorption from a gap and nally
condensation and water leakage.
,
Adjust the camera position
You should adjust the camera angle position as shown below illustration. Adjust the camera angle
position by following step aand b.
1. Adjust the Pan.
CABLE
2. Adjust the Tilt.
CABLE
3. Adjust the Angle.
CABLE
• Camera can be damaged if you adjust the Pan /Tilt / Angle when the screw is
xed.
• Be careful not to rotate the Pan and Angle more than 360°, it may damage the internal
cable.
,
Connection
Precautions
• Be sure to switch o the unit before installation and
connection.
• The installation should be made by qualied service
personnel or system installers.
• Do not expose the power and connection cables to moisture,
which may cause damage to the unit.
Connecting Network
You can control and monitor the system via network. With the
remote control (monitoring), you can change the system
conguration or monitor the image via network. After the
installation, check the network settings for the remote control
and monitoring work.
Connect the IP camera to your network using a standard RJ-45
network cable as shown below.
Broadband
Service
Broadband
Service
Ethernet device
(IEEE802.3af )
Router
Connecting Power Source
Connect a DC 12 V power source to the power input terminal as
shown below.
(Recommended power adapter is DC 12 V / 1.5 A or above)
ETHERNET
With PoE
ETHERNET
With PoE
When the connecting power adapter, tighten the screws
as shown above.
,